Prorack PR3715 User manual

Page 1 of 8
6100015541_PR3715-Rev6
Utility Mount
First Time Installation
• Please read instructions carefully before installation.
• Check the contents of kit. Contact your Prorack dealer if any parts appear to be missing or damaged.
• Clean your roof racks/Aero Deck prior to fitting the Utility Mount kit.
• Place these instructions in the vehicle’s glove box after installation in complete.
Important Warning
• It is critical that all Prorack racks and accessories be properly and securely attached to your vehicle. Improper
attachment could result in an automobile accident, and could cause serious bodily injury or death to you or to others.
• You are responsible for securing the racks and accessories to your car, checking the attachments prior to use, and
periodically inspecting the products for adjustment, wear, and damage.
• If you do not understand all of the instructions and cautions, or if you have no mechanical experience and are not
thoroughly familiar with the installation procedures, you should have the product installed by a professional installer
such as a roof rack specialist.
Kit Contents
Item Component Qty
1 Shovel Holder Assembly 2
2 16 mm Socket Head Capscrew 2
3 20 mm Socket Head Capscrew 2
4 25 mm Socket Head Capscrew 2
5 Star Washer 2
6 Thin Slot Nut 2
7 Thick Slot Nut 2
8 Allen Key 1
9 Key Set 2
CROSSBARS AND SHOVEL SOLD SEPARATELY
1
2
87
6
5
9
4
3
MAX LOAD RATING: 4 KG

Page 2 of 8
6100015541_PR3715-Rev6
Installation
POSITION NUTS IN CHANNEL
Determine the best spacing for the Utility Mounts based on the tool you will be
carrying. For crossbars, it is recommended to position Nuts close to the end of
crossbars and ensure they are equally spaced as shown. The Allen Key can be
used to assist Nut movement within the channel.
=
20 mm
==
25 mm
=
25 mm
1a 1b 1c 1d
16 mm
x2
INSTALLATION ONTO
RECOVERY TRACKS
OR ACCESSORY
MOUNTING BRACKETS
The Slot Nuts can be
used to install the
Utility Mount onto the
Recovery Track Mounts
or Accessory Mounting
Brackets as shown and
following the Aero Bar
installation steps.
AB
A = B

Page 3 of 8
6100015541_PR3715-Rev6
INSERT CAPSCREWS INTO UTILITY MOUNT
Assemble 1 x Star Washer onto each Capscrew.
Insert Capscrew assemblies through hole in
the base of each Utility Mount as shown.
1
x2
Installation to Aero Bars
POSITION AND SECURE UTILITY MOUNTS
Line up Capscrews in the base of each Utility Mount into the nuts in Bar channel.
Tighten all Capscrews to 4 Nm with Allen Key provided.
Your Utility Mounts are ready to use.
2
x2

Page 4 of 8
6100015541_PR3715-Rev6
1
Installation to Aero Deck and HD Bars
2
x2
INSERT CAPSCREWS INTO UTILITY MOUNT
Assemble 1 x Star Washer onto each Capscrew.
Insert Capscrew assemblies through hole
in the base of each Utility Mount.
ADD SLOT NUT TO HOLDER
Add Slot Nut to Capscrew with 1.5 turns until flush.
x2

Page 5 of 8
6100015541_PR3715-Rev6
3
x2
x2
SECURE UTILITY MOUNT TO AERO DECK AND HD BARS
For Aero Deck installation insert Slot Nut
into the Aero Deck as shown.
Slide to location. Tighten to 4 Nm.
Ensure the Slot Nut is fully turned inside the channel.
For HD Bar installation turn slot nut to be parrallel
with slot on HD Bar. When conveniently located
turn the slot nut 90 Degrees. Tighten to 4 Nm.
90 °

Page 6 of 8
6100015541_PR3715-Rev6
1a
INSERT TOOL
Insert tool or paddle down into Utility Mounts.
Ensure any blades are orientated towards the rear of the vehicle and facing up or away from you. The Utility
Mounts can accommodate long handled items with a 30-55 mm shaft diameter including axes, rakes, brooms
and oars to a maximum weight of 4 kg.
1b
Vehicle Rear
Usage
Prorack Aero Deck
Prorack Bars
x2
Unlocked Locked
SECURE TOOL
Secure tool within the Utility Mount by closing the top claw down over tool handle and pushing it down
as far as it can go. The Rubber pads should be compressed to ensure a firm hold. If desired, lock Utility
Holders with keys provided.
2

Page 7 of 8
6100015541_PR3715-Rev6
WHEN NOT IN USE
When not carrying an item, close both
holders completely to
secure rubber pads in place.
If rubber pads are lost, order item
SP209 for a replacement kit.
4
TOOL REMOVAL
To release, unlock the unit
using the keys provided (if
needed), and then squeeze
the side tabs while pulling
the top claw upwards.
3

Page 8 of 8
6100015541_PR3715-Rev6
Caution
• The Utility Mounts can carry up to 4 kg of equipment per pair. Ensure all items are securely attached.
• Ensure that all loads are distributed evenly and are fastened securely.
• A loaded roof rack system can alter the performance of your vehicle. Be especially aware of the effects of side winds,
changing of direction, and braking performance. Avoid rapid acceleration and deceleration. Drive Carefully.
• Never drive into a car wash with the roof rack system or accessories fitted.
• Do not exceed the vehicle manufacturer’s roof load rating. Total load equals weight of roof racks + accessories + cargo/
equipment.
Maintenance
• Check accessory is securely attached whenever you refit it to the vehicle. If the unit feels loose, refer to the fitting
instructions and readjust.
• Regularly check all fasteners. This includes all attached accessories and roof racks.
• Clean with hot soapy water and sponge as required.
ALL CONTENT SUBJECT TO YAKIMA AUSTRALIA PTY LTD COPYRIGHT © 2023
Prorack
17 Hinkler Court, Brendale
QLD 4500, Australia
Freephone
AU: 1800 143 548 www.prorack.com.au
NZ: 0800 4776 722 www.prorack.co.nz