Prorack K776 Operation and installation manual

K776
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 2 x 2 x 1 x 1
Revision No: 1A 1

Fitting Kit K776
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
x 1 x 1
2

Fitting Kit K776
MAX kgs (lbs)
W/P WHD
Peugeot
508, 4dr Sedan 11-+ EU 70 kgs (154 lbs) 70 kgs (154 lbs)
508, 4dr Sedan 11-+ ZA 70 kgs (154 lbs) 70 kgs (154 lbs)
508, 4dr Sedan 11-+ AU 70 kgs (154 lbs) 70 kgs (154 lbs)
508, 4dr Sedan 11-+ NZ 70 kgs (154 lbs) 70 kgs (154 lbs)
3

Fitting Kit K776
X
A B C 1 2 3
508, 4dr Sedan 11-+ (EU) -310mm 400mm - 903mm 875mm -
-12 -3/16ths" 15 3/4ths" - 35 9/16ths" 34 7/16ths" -
508, 4dr Sedan 11-+ (ZA) -310mm 400mm - 903mm 875mm -
-12 -3/16ths" 15 3/4ths" - 35 9/16ths" 34 7/16ths" -
508, 4dr Sedan 11-+ (AU) -310mm 400mm - 890mm 870mm -
-12 -3/16ths" 15 3/4ths" - 35 1/16ths" 34 1/4ths" -
508, 4dr Sedan 11-+ (NZ) -310mm 400mm - 890mm 870mm -
-12 -3/16ths" 15 3/4ths" - 35 1/16ths" 34 1/4ths" -
4

Fitting Kit EN
K776
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
5

Fitting Kit EN
K776
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
6

Fitting Kit EN
K776
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 229A
B = 230A
C = 231A
D = 232A
7

Fitting Kit EN
K776
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
8

Fitting Kit EN
K776
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 261
B = 262
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
9

Fitting Kit EN
K776
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
10