Prorack K997 User manual

K997
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 1 x 1 x 2
x 2 x 2 x 1 x 1
x 2 x 2 x 2
Revision No: 1A 1

Fitting Kit K997
MAX kgs (lbs)
W/P WHD
Jeep
Renegade Sport, 5dr SUV 15-+ AU 68 kgs (149 lbs) 68 kgs (149 lbs)
Renegade Sport, 5dr SUV 15-+ EU 68 kgs (149 lbs) 68 kgs (149 lbs)
Renegade Sport, 5dr SUV 16-+ NZ 68 kgs (149 lbs) 68 kgs (149 lbs)
2

Fitting Kit K997
X
A B C 1 2 3
Renegade Sport, 5dr SUV 15-+ (AU) 275mm 480mm - 915mm 970mm -
10 13/16ths" 18 7/8ths" - 36" 38 3/16ths" -
Renegade Sport, 5dr SUV 15-+ (EU) 275mm 480mm - 915mm 970mm -
10 13/16ths" 18 7/8ths" - 36" 38 3/16ths" -
Renegade Sport, 5dr SUV 16-+ (NZ) 275mm 480mm - 915mm 970mm -
10 13/16ths" 18 7/8ths" - 36" 38 3/16ths" -
3

Fitting Kit EN
K997
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K997
Fitment FRONT ONLY
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
5

Fitting Kit EN
K997
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
6

Fitting Kit EN
K997
●Remove as shown.
●Mark as shown.
Fitment Front Bar Only
●Use drill bit supplied, to drill holes in
marked positions.
7

Fitting Kit EN
K997
●Re-install rubber ditch mould back into roof
channel and click into place.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all items.
●Refer to the underside of the pad for the
part number.
8

Fitting Kit EN
K997
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 224
B = 225
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
9

Fitting Kit EN
K997
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat at other end.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
●If crossbars are removed, please install the
rubber plugs into the ditch moulding.
10