Protege Sppe 200 User manual

............................................................................ pg 3

.................................. pg 4

....................................... pg 5

................................................................ pg 6

...................................................... pg 7

............................................... pg 9

............................................................ pg 10

PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS PROTEGE PUMPS

Self Priming Swimming Pool Pump

anks for buying the Swimming Pool Pump, another high-quality machine from

our company.

To get the most out of your purchase, please read the manual before using the pump.

We ask you to please read this manual carefully beforehand in order to familiarise

yourself with this product and aer reading, please store this instructional manual

for future reference. Failure to follow the proper protocols listed in the manual may

cause personal injury to the operator or damage to equipment.

Self Priming Swimming Pool Pump

• e electrical supply should be single phase 220 -240VAC.

• e pump must be installed in a place where there is easy access to the terminal

box.

• e pump must only be used for swimming pools and garden ponds.

• e pump has to be mounted on a xed and rm base using bolts (not supplied).

• Electrical wiring must be carried out by a licensed electrician.

• If the supply cord is damaged, it must be replaced by the manufacturer, a service

agent or a licensed electrician

• e pump must be earthed.

• Ensure a cable of suitable capacity is used.

• Ensure installation is completed according to your local standards.

• e pump must be protected by a fuse.

• A suitable residual current circuit breaker conforming to your local electrical

standards must be used.

• e ambient temperature must not exceed 40 ° C.

• e pumps are only suitable for counter-clockwise rotation when viewing from

the pump end.

• e pump must be disconnected from all power sources before work/

maintenance is carried out.

• For hard wired applications, a licensed electrician must be used for

disconnection/reconnection.

• is appliance is not intended for use by children or by people with reduced

physical, sensory or mental capabilities.

Self Priming Swimming Pool Pump

• Locate the pump as close as possible to the pool. Provide the necessary space

around and below the pump for inspections and servicing of the unit.

• e pump suction line should not be smaller than the pressure line. All piping

must be airtight.

• When the pump unions are screwed on, the threads on the pump must be sealed

with teon tape or silicone. Tighten the pump union only as much as is required

to ensure a tight connection. Excessive torque is unnecessary and may cause

damage to the pump.

• e weight of the piping should be supported independently and not carried by

the pump.

• e pump motor must be wired for the proper voltage and rotation, in

accordance with the wiring diagram and local regulations. Voltage, phases,

ampere draw and cycles are given on the pump nameplate.

• Fill the pump tank with water before starting. is may be done through the

tank lid. Should the pump be empty or drained, it is necessary to rell it before

starting.

• High suction lis or long suction lines require additional time and reduce

performance of the pump. Should you have diculty with either of these, refer to

the troubleshooting guide.

• e pumped water cools and lubricates the seal. Running the pump dry will

damage the seal. Always keep liquid in the pump tank. No further lubrication of

the pump end is necessary.

• Aer the pump tank has been lled with water and the motor has started, allow

a few moments for the pump to start delivering water. Be sure that all suctions

and discharge valves are open when the pump is running. Operating the pump

with a closed valve in the system can cause pump damage. If ow does not start

within ten minutes, stop the motor and determine cause.

Self Priming Swimming Pool Pump

• If your pool is unused during the winter months, care must be taken to protect

the pump from damage. Drain completely by removing the drain plug at the

bottom of the pump tank. Do not replace the plug but store it in the strainer for

the winter. An alternative is to take the pump indoors and store it somewhere

warm and dry.

• If the pump has been in contact with seawater, it is necessary to ush it with

clean water.

• It is also possible to leave the wet end and piping intact and only remove and

store the motor and impeller assembly. To do this, remove the motor from the

tank screws. Store the remaining parts in a dry place away from liquid.

• When activating the pump again, reverse the above procedure. Replace the body

O-Ring between the tank and the back plate if damaged. Put the drain plug back

in. Check the pump sha for free movement. Prime the pump as above and

check the rotation of the pump sha.

• A licensed electrician is required to carry out all electrical disconnection/

reconnection work.

1. Remove the tank lid to expose the strainer basket.

2. Remove the basket and clean.

3. Inspect the O-Ring on the lid.

4. If it is damaged, replace it

5. Replace the strainer basket and reinstall the lid

6. Tighten by hand only.

Self Priming Swimming Pool Pump

Symptoms Probable Causes Recommended Action

Pump will not prime Suction air leak • Be sure the water in the pool is

high enough to ow through

the skimmer

• Make sure the lid O-Ring is

clean and properly positioned

• Hand tighten tank lid down

snugly

• Tighten all pipes and unions

on suction of pumps

• Remove and replace pump seal

No water in pump • Make sure pump tank is full of

water

Closed valves or blocked lines • Open all valves in system

• Clean skimmer and pump

strainer basket

• Open pump and check for

clogging

Motor does not turn No power to motor • Check that all power switches

are on.

• Be sure fuses and circuit

breakers are properly set

• Make sure the timer is

properly set

• Check the timer for proper

operation

Pump jammed With the power o, turn the sha-

it should spin freely. If not, consult

a licensed electrician.

Low ow Dirty lter Back wash the lter when the lter

pressure is high

Dirty skimmer basket Clean skimmer and pump strainer

baskets

Suction air leak See problem 1

Closed valves of blocked lines See problem 1

Self Priming Swimming Pool Pump

Motor runs hot ese motors will run ‘hot’

to the touch, however, this is

normal. e thermal overload

protector will turn on if

there is an overload or high

temperature issue.

Excessive heat can be caused

by:

Low or incorrect voltage • Wiring to be corrected by

licensed electrician

Installed in direct sun • Shield the motor from the

sun’s rays.

Poor ventilation • Do not cover or enclose the

motor

Noisy operation of motor Bad bearings • Have a licensed electrician

replace bearings in the motor

Noisy operation of pump Air leak in suction line • Repair leak

Bubbles in water returning to

the pool at the inlet

• Check suction pipe

• Check the O-Ring is clean

Restricted suction line due to

blockage or an undersize pipe,

indicated by a high vacuum

reading at the pump suction

• Have a service person remove

blockage or increase the suc-

tion pipe size

• Make sure the strainer basket

is clean

Foreign matter (gravel, metal

etc) in pump impeller

• Have a licensed electrician

disassemble the pump and

remove the foreign matter

from the impeller.

Cavitation • Improve suction conditions

(reduce suction li, reduce the

number of ttings, increase

pipe size)

• Increase discharge pressure

and reduce ow by throttling

discharge

Motor overload protection

‘kicks out’

Motor is improperly connected • Have a licensed electrician

check the wiring diagram on

the motor

Low voltage due to undersized

wire or low incoming voltage

• Have a licensed electrician

check using the volt meter

• Increase size of supply wire

• Report low supply voltage to

the power company

• Voltage of motor must be

within 6% of motor nameplate

voltage

Pump is leaking Seals are worn out • Change the seal

Self Priming Swimming Pool Pump

U2 V2 W2

W1V1U1

R S T~ ~

U2 V2 W2

W1V1U1

R S T~ ~

U2 V2W2

V1 W1

R S T~ ~

U2 V2

V1 W1

R S T~ ~

*For use by a licensed electrician

Self Priming Swimming Pool Pump

Model SPPE 200

Power 1200 Watts/ 1.6 HP

Volts 240 - Hz 50

Max Flow 450 L/m

IP55 INS CL.F Max 50 ° c

Amps 5.0

Head Max 18m

Capacitor 17 µ F

Model SPPE 100

Power 550 Watts/ 0.75HP

Volts 240 - Hz 50

Max Flow 240 L/m

IP55 INS CL.F Max 50 ° c

Amps 2.2

Head Max 14m

Capacitor 10 µ F

Model SPPE 250E

Power 1850 Watts/ 2.5HP

Volts 240 - Hz 50

Max Flow 560 L/m

IP55 INS CL.F Max 50 ° c

Amps 6.8

Head Max 19m

Capacitor 25 µ F

Some experts believe the incorrect or prolonged use of almost any

product could causeserious injury or death. For information that

may reduce your risk of serious injury or death consult thepoints

below and additionally, the information available at

www.datastreamserver.com/safety

- Consult all documentation, packaging and

product labelling be fore use. Note that some

products feature online documentation which

should be printed and kept with the product.

- Check product for loose / broken / damaged /

missing parts, wear or leaks (if applicable) be fore

each use. Never use a product with loose / broken

/ damaged / missing parts, wear or leaks (if

applicable).

- Products must be inspected and serviced (if

applicable) by a qualified specialist every 6

months assuming average residential use by a

person of average weight and strength, ab ove

average technical aptitude, on a property

matching average metropolitan specification.

Intended use outside these guidelines could

indicate the product is not suitable for intended

use or may require more regular inspection or

servicing.

- Ensure all possible users of the p roduct have

completed an industry recognised training course

before being given access to the product.

- The product has been supplied by a general merchandise

retailer that may not be familiar with your specific applic ation or

your description of the application. Be sure to attain third party

approval for your application from a qualified specialist before use

regardless of prior assurances by the retailer or its representatives.

- This product is not intended for use where fail-safe operation is

required. As with any product (take an automobile, aircraft,

computer or ball point pen for example) there is always a small

chance of a technical issue that needs to be repaired or may

require replacement of the product or a part. If the possibility of

such failure and the associated time it takes to rectify could in any

situation inconvenience the user, business or employee or could

financially affect the user, business or employee then the product

is not suitable for your requirements. This p roduct is not for use

where incorrect operation or a failure of any kind, including but

not limited to a condition requiring product return, replacement,

service by a technician or replacement of parts could cause a

financial loss, loss of employee time or an in convenience

requiring compensation.

- If this item has been purchased in error considering the points

above simply contact the retailer directly for details of their

returns policies if required.

This manual suits for next models

Popular Swimming Pool Pump manuals by other brands

T.I.P.

T.I.P. SPP 400 FT operating instructions

Hayward

Hayward Power-Flo Matrix Series Installation and operating instructions

Pontec

Pontec PondoMax Eco 1500 operating instructions

IML

IML AMERICA SA Series Installation and maintenance manual

Davey

Davey WHISPER Series Installation and operating instructions

Intex

Intex CS15220 owner's manual

HeatPumps4Pools

HeatPumps4Pools LCSPC-40 Installation and Maintenance

HydroPro

HydroPro + premium 7 Installation instructions manual

Blue Wave

Blue Wave TIDAL WAVE MAXI II instruction manual

APF

APF VIPOOL MJB VSD Information

Aquagem

Aquagem XFIow INVERSilence GFVS09N Installation & operation manual

Viron

Viron P320 eVo Installation and operating instructions

OEG

OEG 650 001 082 Installation and operating instructions

Harmopool

Harmopool Harmo Kubi ZVWX4015 instruction manual

T.I.P.

T.I.P. CoverOne 1500 AUT Translation of original operating instructions

onga

onga LTP400 owner's manual

Polaris

Polaris PB4-60 installation instructions

Polygroup

Polygroup SUMMER WAVES SKIMMERPLUS SFX330 owner's manual

Protege SPPE 200 User manual

Popular Swimming Pool Pump manuals by other brands