Protex PR100 User manual

DIAGRAM 1.0
DIAGRAM 2.0
Step 1 –
Opening the safe using the master code:
1. Press *, enter the master code, then press #. Factory
default code is: 7-7-7-7-7-7
2. The LED will light GREEN.
3. Open the door using the handle.
Opening the safe using the user code:
1. Press *, enter the user code, then press #. Factory default
code is: 0-0-0-0
2. Open the door using the handle.
ENROLLING:
Step 2 – Changing the master code:
1. Press #, enter the master code, then press #. Factory default
code is: 7-7-7-7-7-7
2. The LED will light ORANGE.
3. Now: (while the LED lights ORANGE)
a. Press 1 followed by the *key.
b. Enter the new master code (6 digits), then press #.
c. Enter the new master code again and press #.
d. The lock will beep twice.
Note: After changing the master code, all other codes will be
deleted.
Step 3 – Changing the user’s code:
1. Press #, enter the master code, then press #.
2. The LED will light ORANGE.
3. Now: (while the LED lights ORANGE)
a. Enter user’s ID (2 thru 7) followed by the *key.
b. Enter the new user code (4-8 digits), then press #.
c. Enter the new user code again and press #.
d. The lock will beep twice.
Step 4 – Deleting individual user code:
1. Press #, enter the master code, then press #.
2. The LED will light ORANGE.
3. Now: (while the LED lights ORANGE)
a. Enter user’s ID (2 thru 7).
b. Then press * # #.
c. The lock will beep twice.
2 3

Step 5 – Dual code setting:
Single Code Mode: (Default)
1. Press #followed by the master code, then #0 #0 #.
2. Now any user code or master code will open the safe.
Dual Code Mode:
1. Press #followed by the master code, then #2 #2 #.
2. Now in order to open the safe, you must enter the master
code and user code in any order.
Example: Press *then 7-7-7-7-7-7 (master code) followed by #,
now enter 0-0-0-0 (user code) followed by #. NOTE: You have 60
seconds between entering the first code and the second code
before the system goes back to sleep mode.
Step 6 – Time delay setting:
The time delay can be set from 1 to 99 minutes
1. Press #followed by the master code, then #01-99 #01-99 #.
(05 = 5 minutes)
2. Now in order to open the safe, press the *key to activate the
time delay, the LED will flash YELLOW every 5 seconds. In the
last 10 seconds the LED will flash faster and the lock will beep
twice when the time delay is done. Now you have 2 minutes
to enter the code and open the safe.
Example: Press #then 7-7-7-7-7-7 (master code) followed by #,
now enter 05 followed by #, then enter 05 followed by #. 05
represents 5 minutes.
Removing the time delay feature:
1. Press #followed by the master code, then #00 #00 #.
2. Now the lock as returned to normal operation mode, without
the time delay feature.
EMERGENCY OPENING:
Electronic-Key Override:
1. Please contact Protex Safe Co. @ 818-610-8030 ext. 302 to
obtain more information.
Replacing the batteries:
Hold the metal part of the keypad with your hands and turn to
the left (counterclockwise) to remove the keypad and expose
battery tray. Replace the 4 “AAA” batteries with high-quality
batteries. The lock will remember all codes and setting without
power.
User Manual
For
PR100
Electronic Safe Lock
Rev. 102907
4