ProtoMachines LED8 Assembly instructions

Operating / Safety Instructions
ProtoMachines
www.ProtoMachines.com
[email protected]
Thank you for choosing the ProtoMachines LED8 full color
LED light. It is the result of years of research and
development and represents the cutting edge of full color
LED technology. Please review these instructions carefully
to familiarize yourself with the design and operation of this
device.
SPECIFICATIONS:
Model number: LED8
Input voltage: 7.4VDC
Input power: 10 watts
Ambient temperature: 32F - 122F
(1)
(0C - 50C)
Humidity: 85% or less
Weight: 0.85lb (390g)
Dimensions: 8” x 4” x 2.5” LWH
(203 x 102 x 64mm)
Power source: 2x 18650 li-ion
(protected PCB cells only)
oSpecifications subject to change without notice.
oDesignated trademarks and brands are the property of their respective owners.
1. Duty cycle may be reduced while operating in hot environments.
© 2017 ProtoMachines LLC All rights reserved.
IMPORTANT SAFETY
INSTRUCTIONS:
WARNING:
When using any battery operated device, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and personal
injury. Please read this instruction manual carefully and
understand it fully before use.
1. Keep out of reach of children. This is not a toy.
2. Do not expose device to impacts or strong vibration.
Do not crush. The device may malfunction if damaged.
Remove batteries and discontinue use.
3. Keep dry. Do not immerse or expose to water. If water
gets inside the device, promptly remove the batteries.
4. Keep dust and debris away from the controls.
5. Do not disassemble or modify this device. There are no
user serviceable parts inside.
6. The device may become hot during usage. Avoid
contact with the heatsink. Maintain adequate airflow
around the heatsink at all times.
7. Not intended for use as the sole source of illumination
in critical survival or hazardous environments. Always
carry a backup light source.
8. To prevent accidents or excessive battery drain, always
remove the batteries after use, before storage or
transport.
9. Observe all safety rules and regulations regarding the
handling and transport of lithium ion batteries.
10. If any problem develops, consult your reseller or
ProtoMachines for assistance.
WARNING:
This is powerful LED light source. Always use
common sense when operating this product.
Do not stare directly into the beam.
Do not aim at your eyes, the eyes of other people or
animals. Prolonged exposure may result in injury or
blindness.
Please do not use this product if you do not fully understand
these instructions and warnings.
LIMITED WARRANTY
Before using this product, please read this warranty
carefully. By using your LED8, you agree to the terms and
conditions of this warranty. If you do not accept this
warranty, do not use your LED8. ProtoMachines will not be
liable for any indirect, incidental, or punitive damages arising
from use of this product.
The LED8 is warranted to the original purchaser to be free
from manufacturing and component defects for one (1) year
from the date of purchase. This limited warranty is the sole
and exclusive remedy, offered in lieu of all other warranties,
expressed or implied. ProtoMachines LLC has sole
discretion to determine manufacturer’s defects and will (at its
option) repair or replace it, or refund the purchase price.
Repair may use new or refurbished parts. Replacement may
be with a new or refurbished unit.
This warranty does not cover normal wear and tear, damage
caused by accident, abuse, misuse, modification of the
product, external causes such as acts of nature, or damage
to or from any non-ProtoMachines product used in
conjunction with this product. This warranty is void if the
product is disassembled or used for commercial and/or
rental purposes.
OPERATION
Installing the batteries
The LED8 requires by two (2) 18650 Li-ion PCB protected
batteries capable of at least 3A discharge rate. If unsure,
please consult website or tech support for assistance.
Always use cells of equal capacity and charge level.
Always switch the light off before inserting or removing the
batteries.
1. Slide latch towards the rear and open battery door.
2. Insert two (2) 18650 Li-ion batteries with polarities as
shown.
3. Close the battery door while holding the latch in the open
position. DO NOT use excessive force. Latch should
spring back to full-forward position after the door is closed.
Removing the batteries
1. Press and hold the front edge of the battery door to
release the battery latch.
2. Slide battery latch towards the rear to open door.
3. Remove batteries and re-close battery door.

User controls
Switching device On/Off
Make sure batteries with adequate charge are installed.
To switch OFF, press and hold the POWER/BACKLIGHT
button for 3-4 seconds until the device switches off.
To switch ON, press and hold the POWER/BACKLIGHT
button for 3-4 seconds until the device switches on.
Sleep mode
The LED8 will automatically enter Sleep Mode after being
inactive for a few minutes. Pressing the TRIGGER switch
will wake the LED8 out of Sleep Mode.
Switching LED output On/Off
Make sure batteries with adequate charge are installed.
Press TRIGGER switch once to turn the LED output on.
Press TRIGGER switch again to turn the LED output off.
Home Screen
The Home Screen displays a snapshot of the LED8’s current
settings and status.
Adjusting the active settings
To change the active color settings, press the OK/Menu
button from the Home screen. This will cycle through the
menus available for the current color mode. You may use
the THUMBSTICK to adjust the current setting, or the
OK/Menu button to accept the setting.
Adjust hue over 0-359° range in
HSB color space.
Adjust saturation over 0-100%
range in HSB color space.
Set output power over 1.0 - 8.0
range in 1/10
th
stop increments.
Adjust simulated white balance
from 2500K to 9500K.
Adjust hue cycling rate during
auto hue cycle mode.
Sets exposure timer in 1 second
increments or ‘---‘ to disable.
NOTE - the new timer value will not become active until the next time the output
is switched on using the POWER switch.
Color mode
Press and hold the OK/Menu button until color mode
selection menu is displayed. Use the THUMBSTICK and
OK/Menu buttons to make your selection.
HSB – Adjust hue over 360° range and saturation over a
0-100% range.
Hue cycle – Hue cycled automatically at a tunable rate
whenever LED output is switched on.
HSB (RAW) – Maximize light output for general
illumination. Not balanced for photo/video use.
White – Simulated white balance output, adjustable from
2500K to 9500K.
Recalling presets
The PRESET buttons can be used to recall a combination of
hue, saturation, power level and exposure duration. The
PRESET buttons operate in a similar fashion to presets on a
car radio.
Presets 1 - 4 may be retrieved by a single press to their
numbered buttons, while presets 5 - 8 may be retrieved with
a double-press to buttons 1- 4respectively. For example,
button 1will retrieve preset 1 if single pressed and preset 5 if
double-pressed.
Storing presets
Once you have tuned your desired color/power/timer
settings, press and hold the appropriate 1 - 4 PRESET
button until the preset save menu is displayed. The display
will alternate between “SINGLE press” and “DOUBLE press”.
Release the PRESET button when the desired setting is
displayed.
Backlight operation
The backlight may be temporarily disabled by pressing the
BACKLIGHT button. Pressing it again toggles it back on.
The backlight will turn off automatically when the LED8
enters Sleep mode. Manually toggling the backlight will not
trigger sleep mode nor extend battery life noticeably.
Battery level indicator
The battery level icon will give an estimation of remaining
battery life. If the level meter is low or blinking, replace
depleted batteries with freshly charged ones.
Temperature warning indicator
The temperature warning indicator may be displayed if the
ambient temperature is too high or if the LED8 has been
operated continuously for long periods of time. If the
temperature limit is exceeded, the LED8 will enter shutdown
mode to prevent further damage. This is indicated by a
blinking temperature warning icon.
Please wait for the LED8 to cool before resuming use. To
prevent overheating, make sure the heatsink is clear of all
obstructions and always maintain adequate airflow around
the LED8. Using a slightly lower power setting with a longer
exposure time may also help.
Restore to factory defaults
To reset settings to factory defaults, remove the battery and
then re-install it while holding down the OK/Menu button
until the “Reset settings” option is displayed. Use the
THUMBSTICK and OK/Menu buttons to make your
selection.
CARE AND STORAGE:
Cleaning
Wipe the body of the LED8 gently with a soft dry cloth to
remove most dust and fingerprints. For persistent dirt, clean
the surface with a soft cloth slightly moistened with water,
then wipe the surface with a dry cloth.
To clean the LCD screen or front lens, wipe the surface
lightly with a soft dry cloth only. Do not apply pressure.
Do not expose to organic solvents, oils or corrosive
chemicals.
Storage
When the LED8 will not be used for an extended period of
time, remove the batteries and store it in a cool, dry area
away from direct sunlight. Do not store your LED8 near
flammable or corrosive chemicals, near strong
electromagnetic fields, or in temperatures above 122°F
(50°C) or below 32°F (0°C).
LED8 - Rev 1.20