Prudential Bionic 4 User manual

Page 1 of 4, April14
Flush Regressed
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
INSTALLATION INSTRUCTIONS
Bionic™4 — PERIMETER, CONTINUOUS RUN X1, X2, X6
5-1
/2˝6-1
/2˝
6˝
6˝
PARTS SHIPPED SEPARATELY
Wall Rail Trim & Wall Trim Lens
8-32 x 3/8˝ Self-tapping
Machine Screws
Overhead Mounting
Bracket
END VIEW
SCALE 1 : 1 FRONT VIEW
SCALE 1 : 1
PICTORIAL VIEW
SCALE 1 : 1
Part Number
Rev
Description
Finish
Material
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Check
Appr Date
Date
Sheet
Drawing Size Drawn By Date Project
Scale
Prudential LTG
82484
R. CORTEZ
1
Galvanized Steel
9/4/2012
NOTED
NOTED
LENS REMOVER TOOL
BIONIC/P40 SERIES
A
2.562
.437
75°
1.000
.250
.187 X .375 SLOT
GENERAL NOTES: UNLESS SPECIFIED 1- MATERIAL : 2- ALL ROUNDS AND FILLETS TO BE .030 RAD. 3- TOLERANCE : .X = ±.03, .XX = ±.010, .XXX = ±.005 4- ALL ANGLES TO BE ±.5° 5- FINISH : AS SPECIFIED
#24 GA. GALVANIZED
R.125 (TYP.)
Adjustable Hanger
Brackets
Lens Removal Tool
Notes:
1. Housing ships separated from gear tray, reectors and lens.
for easy installation (gear tray for STG only).
2. Remove specular reector protective coating (if required).
3. Install lamps (by others).
Aligner Splines
WALL RAIL
INSTALL L-SHAPED END TRIM (LP INSTALLS ONLY)
T-bar Brackets
1) Identify housing:
Start/End units are capped on one end.
Intermediate units are not capped.
Individual units are capped on both ends.
X3/X7 Start/End Unit
Intermediate Unit
X1/X2/X6
Start/End Unit
Part Number
Rev
Description
Finish
Material
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Check
Appr
Date
Date
Of
Drawing Size Drawn By Date Project
Scale
Sheet
Prudential LTG.
BVAULT
REVISION HISTORY
REV DESCRIPTION DATE REV. BY
X3/X7 Start/End Unit
Intermediate Unit
X1/X2/X6
Start/End Unit
Part Number
Rev
Description
Finish
Material
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Check
Appr
Date
Date
Of
Drawing Size Drawn By Date Project
Scale
Sheet
Prudential LTG.
BVAULT
REVISION HISTORY
REV DESCRIPTION DATE REV. BY
X1/X2/X6 Start/
End/Individual
Intermediate
1˝

5"
4) Remove Shipping Strap.
Secure housing to structure
(multiple options). X
Y Y
Top view of Option A Installation hole spacing
X= 2´ Y = 9˝ from center hole
X= 3´ Y = 15˝
X= 4´ Y = 21˝
X= 5´ Y = 27˝
X= 6´ Y = 33˝
X= 7´ Y = 39˝
X= 8´ Y = 45˝
1/4-20 all thread
can protrude into
housing no more
than 3/8˝
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
Page 2 of 4, April14
INSTALLATION INSTRUCTIONS
Bionic™4 — PERIMETER, CONTINUOUS RUN X1, X2, X6
Wall cleat
Optional perimeter overhead
bracket for mounting 1/4-20 all
threaded - see page 5 for drawings.
2) Install wall rail for entire row length. 3) Install‘L’ shaped end trim
(LP LightPocket installs only).
INSTALL L-SHAPED END TRIM (LP INSTALLS ONLY)
DETAIL A
SCALE 1 / 4
3-1 /8˝ Above Finish Ceiling - FLSH
4-1 /8˝ Above Finish Ceiling - REG1
6-1 /8˝ Above Finish Ceiling - REG3

8) Swing all Safety Brackets back
and secure.
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
Page 3of 4, April14
INSTALLATION INSTRUCTIONS
Bionic™4 — PERIMETER, CONTINUOUS RUN X1, X2, X6
5) Slide & tighten aligner splines over joint,
(2) per Seamless, Flush & 1”REG,
(3) per REG3.
6) Fasten Inside Joiner Brackets on row
mounted housings.
Part Number
Rev
Description
Finish
Material
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Check
Appr
Date
Date
Of
Drawing Size Drawn By Date Project
Scale
Sheet
Prudential LTG.
INTERNAL JOINER BRACKET ISO
BIONIC
B
VAULT
REVISION HISTORY
REV DESCRIPTION DATE REV. BY
8-32 x 3/8”
7) Snap“Gear tray”into housing
(where required).
WARNING! Failure to properly install
Safety Brackets will void warranty.
Note: Plug
Quick Connects
as you install
each Gear Tray.
5"
NOTE: Use ller reectors
at end of row if needed.
Trim to t.
10) Install lamps (by others).9) Install reflectors.
11) Install lensing, cut last piece to fit .
NOTE: Leave 1/16˝ air
gap at each end of run
Table saw or chop saw
with a 80 T blade
recommended

1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
Page 4 of 4, April14
INSTALLATION INSTRUCTIONS
Bionic™4 — PERIMETER, CONTINUOUS RUN X1, X2, X6
Overhead support bracket
5˝ – ush
6˝ – 1˝ regress
8˝ – 3˝ regress
Wall
1
/2˝ K.O. on
top cover of
housing
8 15/16˝
6 3/4˝
5 3/4˝
2 1/4˝