1. Charge the PRYMEBLU Wireless PTT
2. Pair the PRYMEBLU Adapter with a wireless headset
3. Pair the PRYMEBLU PTT with the PRYMEBLU Adapter
4. Test and Use.
3 4
Pairing With an Audio AccessoryQUICK START
2
Controls and Connection
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure
compliance requirements, please avoid direct contact to the transmitting antenna
during transmitting.
RF Exposure Warning!
Please keep product 20cm away from your
body or bystander during the radio operation.
The typical handheld two-way radios were
certied under mobile usage condition
(i.e. keep 20cm away from the user body)
and use of such radio closer than 20cm may
exceed the US RF exposure limit
and shall be avoided.
version 1.0 December 2010
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: 714.257.0600
TOLL FREE: 800.666.2654
WWW.PRYME.COM
PRYMEBLU®PUSH-TO-TALK USER’S GUIDE
For use with PRYMEBLU wireless
Bluetooth Adapters (Sold Separately)
The PRYMEBLU BT-PTT allows you to Push-to-Talk wirelessly
over your two-way radio when using with a PRYMEBLU Adapter
and a compatible wireless headset.
PRYME® and PRYME BLU™ are trademarks owned by PRYME Radio Products,
Brea CA. All other product or service names are the property of their respective owners.
© 2010 PRYME Radio Products, Brea CA. All Rights Reserved
This manual applies to the
PRYMEBLU BT-PTT Wireless
Push-to-Talk transmitter.
The PRYMEBLU PTT works
with all PRYMEBLU BT-500
series Bluetooth Adapters.
PRYMEBLU PTT
Model No.: BT-PTT
Made in Taiwan
FCC ID N2E-BT-PTT
STEP ONE: Charging the PRYMEBLU PTT
The PRYMEBLU PTT has an internal Lithium Ion rechargeable battery pack which must be charged prior
to operation, and must be recharged regularly. A fully charged battery will provide approximately 12
hours (or more) of operation before needing to be recharged.
To charge the PRYMEBLU PTT:
* Ensure the PRYMEBLU PTT is turned o, using the switch located on the back of the device.
* Plug the supplied wall charger into an AC (110V) wall outlet.
* Plug the charger into charge jack on the bottom of the PRYMEBLU Adapter. You will need to remove
the protective rubber cover that is inserted into the charge jack. (To prevent dust and moisture from
damaging your PTT, always ensure this cover is in place when you are not charging the PRYMEBLU PTT.)
* The PRYMEBLU PTT takes approximately 4.5 hours to charge. Actual charge time will vary depending
on several factors including the battery’s charge state, condition, and age.
Charging Cautions:
- Use only the wall charger supplied by the manufacturer. Do not use any other charger.
- Do not use a wall charger that appears to be damaged. (Example: frayed wires, melted plastic, etc.)
Contact PRYME to get a new manufacturer-approved replacement charger.
- Do not tamper with or modify the PRYMEBLU PTT or charger.
-Always turn the power switch to the O position when charging the PRYMEBLU PTT.
STEP TWO: Pairing the PRYMEBLU Adapter and Wireless Headset
In order to operate, the PRYMEBLU PTT must be paired to PRYMEBLU Adapter (BT-500 series).
However, The PRYMEBLU Adapter must rst be paired to a wireless Bluetooth headset. To pair these
devices, follow this procedure:
Pairing the PRYMEBLU Adapter and Bluetooth Headset
* The PRYMEBLU Adapter must be connected to a compatible radio with a freshly charged battery.
Ensure the two-way radio, Bluetooth headset, and PRYMEBLU PTT are all powered o.
* Place the PRYMEBLU Adapter in Accessory Pairing mode. To do this, turn the two-way radio on while
holding down the Talk button on the PRYMEBLU Adapter. Continue to hold the Talk button down for
approximately three seconds. Release the Talk button when the status LED ashes two times per
second. The PRYMEBLU Adapter is now in audio accessory pairing mode.
* Activate the pairing mode on your Bluetooth headset by following the instructions provided by the
headset’s manufacturer. Once the wireless audio accessory and PRYMEBLU Adapter are paired with
each other, the status
LED on the PRYMEBLU Adapter will show a constant blue light for three seconds.
* Once the headset and PRYMEBLU Adapter have been successfully paired, turn o the two-way radio
and Bluetooth headset and wait at least three seconds.
Pairing the PRYMEBLU Adapter and PRYMEBLU PTT
* Turn on the two-way radio while holding down the Talk button on the PRYMEBLU Adapter. Continue
to hold the Talk button down for approximately three seconds. Release the Talk button when the
status LED ashes two times per second. Then, press the Talk button again. The LED should now ash
three times per second, indicating that the PRYMEBLU Adapter is now in PTT Pairing mode.
* Place the PRYMEBLU PTT in pairing mode by holding down the Push-To-Talk button while moving
the power switch to the On position. Continue to hold down the Push-To-Talk button until the LED
indicator on the PRYMEBLU PTT ashes blue continuously. You can then release the Push-to-Talk
button. The PRYMEBLU PTT is now in pairing mode.
* Once the PRYMEBLU Adapter and PRYMEBLU PTT are paired with each other, the status LED on the
PRYMEBLU Adapter will show a constant blue light for three seconds and the LED on the PTT will show
one blue ash every second.
* If the PRYMEBLU Adapter or PRYMEBLU PTT does not detect a compatible wireless accessory within
60 seconds of being put into pairing mode, the devices will exit the pairing mode and resume normal
operation.
* After pairing is successful, turn o the PRYMEBLU PTT and the two-way radio that the PRYMEBLU
Adapter is attached. Wait at least three seconds.
USING THE FRICTION PAD
The PRYMEBLU PTT is supplied with a rubber Friction Pad. This pad provides additional protection and
stability when using the Velcro Fastener on the back of the PRYMEBLU PTT to attach the device to an
automobile steering wheel, gearshift, or any other location.
To install the rubber Friction Pad do the following:
1. Open the Velcro Fastener on the back of the
PRYMEBLU PTT so that the two straps are separated.
2. Align the Friction Pad so that it is centered over the
Velcro Fastener on the back of the PRYMEBLU PTT.
3. Slide one strap of the Velcro Fastener into one
of the slots in the Friction Pad and pull the strap through.
4. Slide the other Velcro Fastener strap through the other slot in the Friction Pad.
5. Place the PRYMEBLU PTT in the position you wish to mount it and close the Velcro Fastener.
Push-To-Talk Button
When paired with a PRYMEBLU Adapter
and wireless headset, this button functions
as a Push-to-Talk, causing the two-way radio
to transmit when the switch is pressed.
LED Indicator
The LED ashes messages that let
the user know the current status of
the PRYMEBLU PTT.
Charge Jack
This jack is used to connect the
PRYMEBLU PTT to the supplied
wall charger.
Lanyard Attachment Point
Allows attachment of a wrist strap
or lanyard to the PRYMEBLU PTT.
Velcro Fastener
The Velcro strap on the back of the
PRYMEBLU PTT rotates 360° and allows
the PRYMEBLU PTT to be securely attached
in many convenient locations, such as to
the user’s clothing, around the user’s ngers,
on an automobile steering wheel, on duty
gear, and many more!
Power Switch
Turns the
PRYMEBLU PTT
on and o.
ON
ON
