Pulsar PSDCB18129B User manual

PSDCB18129B
v.1.0
PSDCB 13,8V/9A/18x0,5A/7Ah
Buffer, switch mode power supply
for CCTV
EN
Edition: 4from 16.12.2014
Supercedes the edition: 3from 28.05.2014
GREENPOWERCCTV

www.pulsar.pl PSDCB18129B
2
Features:
DC 13,8V/9A* uninterruptible power supply
18 outputs, protected with 0,5A glass fuses
fitting battery: 7Ah/12V
wide range of mains supply: 176÷264V
high efficiency 83%
battery charging and maintenance control
excessive discharging (UVP) protection
battery charging current 1A/4A changed with
jumper
battery output full protection against short-circuit
and reverse polarity connection
LED indication
protections:
SCP short-circuit protection
OVP overvoltage protection
overvoltage protection
against sabotage
overload protection (OLP)
warranty –2 year from the production date
CONTENTS:
1. Technical description.
1.1 General description
1.2 Block diagram
1.3 Description of PSU components and connectors.
1.4 Specifications
2. Installation.
2.1 Requirements
2.2 Installation procedure
3. Operating status indication.
3.1 LED indication of operating status
4. Operation and use.
4.1 Overload or short circuit of the PSU output (SCP on)
4.2 Battery-assisted operation
4.3 Maintenance
1. Technical description.
1.1 General description.
A buffer PSU is intended for an uninterrupted supply to devices requiring stabilised voltage of 12V DC
(+/-15%). The PSU provides voltage of U=13,8V DC.Current efficiency:
1. Output current 18x0,5A + 1A battery charge
2. Output current 18x0,38A + 4A battery charge
Total device current + battery: 11A max*.
In case of power decay, a battery back-up is activated immediately. The PSU is constructed based on the
switch mode PSU, with high energy efficiency. The PSU is housed in a metal enclosure (colour RAL 9003) which
can accommodate a 7Ah/12V battery. A micro switch indicates door opening (front cover).
*Refer to chart 1

www.pulsar.pl PSDCB18129B
3
1.2 Block diagram (fig.1)
Fig.1. The block diagram of the PSU.
1.3 Description of PSU components
Table 1. Elements and connectors of the fuse block (tab.1, fig.2).
Element no.
[fig. 2]
Description
[1]
F1÷F9 glass fuses PTC
[2]
LED L1 ÷L9 signaling presence of output voltage DC
[3]
power supply output AUX1÷AUX9, shared terminal COM (-)
Fig.2. The view of the fuse block LB9

www.pulsar.pl PSDCB18129B
4
Table 2. Description of PSU components and connectors ( tab.2)
Element no.
[Fig. 3]
Description
[1]
PSU module
[2]
L-N power-supply connector 230V/AC, PE protection connector
[3]
green LED indicates AC power
[4]
P1 potentiometer, output voltage adjustment
[5]
BAT+/GND: battery outputs + BAT=red, - GND=black
[6]
TAMPER, contact of sabotage protection (NC)
[7]
Additional connector for LED indication
[8]
Ibat - Selection jumper for charging current:
Ibat =1A Ibat =4A
Legend: jumper installed, jumper removed.
Factory settings: Ibat =1A (jumper installed).
[9]
fuse block LB9-A
[10]
fuse block LB9-B
Fig.3. The view of the PSU.
1.4 Specifications:
- electrical parameters (tab.3)
- mechanical parameters (tab.4)
- operation safety (tab.5)
- operating parameters (tab.6)

www.pulsar.pl PSDCB18129B
5
W
H
D
Electrical parameters (tab. 3)
Mains supply
176÷264V AC
Current up to
1,4A@230VAC
Supply power
155W max.
Efficiency
83%
Output voltage
11V÷13,8V DC –buffer operation
9,5V÷13,8V DC – battery-assisted operation
Output current tAMB<30°C
18x0,5A + 1A battery charge - refer to chart 1
18x0,38A + 4A battery charge - refer to chart 1
Output current tAMB=40°C
18x0.37A + 1A battery charge - refer to chart 1
18x0.2A + 4A battery charge - refer to chart 1
Voltage adjustment range
12÷14V DC
Ripple
120mV p-p max.
Battery charge current
1A/4A max. @ 7Ah (± 5%)
Short-circuit protection SCP
LB9 STRIP (A, B)
9x F 0,5A glass fuse
Overload protection OLP
105-150% of power supply, automatic recovery
Battery circuit protection SCP and reverse
polarity connection
polymer fuse
Surge protection
varistors
Overvoltage protection OVP
>16V (automatic recovery)
Excessive discharge protection UVP
U<9,5V (± 5%) –disconnect of connection battery
Tampering protection system:
- TAMPER –indicating unwanted opening of the
PSU’s enclosure
- microswitch, NC contacts (enclosure closed),
0,5A@50V DC (max.)
LED indication:
- AC diode indicating AC power status
- AUX diode indicating DC power status at
the PSU output
- red, normal status –on, failure: off
- green, normal status –on, failure: off
F1÷F9 fuse (strips A,B)
F 0,5A/250V
Mechanical parameters (tab. 4)
Enclosure dimensions
280 x 292 x 80+8 [mm] (WxHxD)
Fixation
see figure 3
Fitting battery
7Ah/12V (SLA) max.
185x105x75mm (WxHxD) max
Net/gross weight
2.53kg / 2.73kg
Enclosure
Steel plate, DC01 0,7mm colour: RAL 9003
Closing
Cheese head screw x 2 (at the front), lock assembly possible
Connectors
Power supply: Φ0,63-2,50 (AWG 22-10)
OutputsФ0,41÷1,63 (AWG 26-14), battery output BAT: 6,3F-2,5
TAMPER output: wires
Notes
The enclosure does not adjoin the assembly surface so that cables can be led.
Operation safety (tab.5)
Protection class PN-EN 60950-1:2007
I (first)
Protection grade PN-EN 60529: 2002 (U)
IP20
Electrical strength of insulation:
- between input and output circuits of the PSU (I/P-O/P)
- between input circuit and PE protection circuit (I/P-FG)
- between output circuit and PE protection circuit (O/P-FG)
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500V/DC

www.pulsar.pl PSDCB18129B
6
Operating parameters (tab.6)
Operating temperature
-10ºC...+40ºC (see: chart 1)
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106
Chart 1. Acceptable output current from the PSU depending on ambient temperature.
2. Installation.
2.1 Requirements.
The buffer PSU shall be mounted by a qualified installer with appropriate permissions and qualifications for
230V/AC installations and low-voltage installations (required and necessary for a given country). The device shall
be mounted in confined spaces, according to the environment class II, with normal air humidity (RH=90% max.
without condensation) and the temperature from -10°C to +40°C. The PSU shall work in a vertical position that
guarantees sufficient convectional air-flow through ventilating holes of the enclosure.
Before installation, prepare a PSU load balance:
1. Output current 18x0,5A + 1A battery charge
2. Output current 18x0,38A + 4A battery charge
Total device current + battery: 11A max*.
As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an
appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be
informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The
electrical system shall follow valid standards and regulations.
2.2 Installation procedure.
1. Before installation, cut off the voltage in the 230V power-supply circuit.
2. Mount the PSU in a selected location and connect the wires.
3. Connect the power cables (~230VAC) to L-N clips of the PSU. Connect the ground wire to the clip marked by the
earth symbol PE (PSU module connector). Use a three-core cable (with a yellow and green PE protection wire) to
make the connection. Lead the cables to the appropriate clips through the insulating bushing of the connection
board.
*Refer to chart 1

www.pulsar.pl PSDCB18129B
7
RED LED:
on –the PSU is supplied with 230V AC
off –no 230V AC supply
GREEN LED:
on –DC voltage in the AUX output of the PSU
off –no DC voltage in the AUX output of the PSU
The shock protection circuit shall be performed with a particular care, i.e. the yellow and
green wire coat of the power cable shall stick to one side of the terminal - marked with
‘‘symbol on the PSU enclosure. Operation of the PSU without the properly made and
fully operational shock protection circuit is UNACCEPTABLE! It can cause a device
failure or an electric shock.
4. Connect the receivers’ cables to the AUX1…AUX9 connectors on the LB9 (A, B) strips.
5. Connect the power (~230V)
6. Connect the battery (mind the colours):
- battery output (+V): BAT+ cable / red,
- battery output (- V): BAT –cable / GND / black.
7. Check the PSU operation indicator: green LED.
8. Check the PSU output voltage:
- the PSU voltage without load should amount to U=13,8V DC.
9. After installing and checking proper working, the enclosure can be closed.
3. Operating status indication.
3.1 LED indication of operating status.
The PSU is equipped with two diodes on the front panel:
4. Operation and use.
4.1 Overload or short circuit of the PSU output (SCP on)
The AUX1 ÷ AUX9 PSU outputs of the LB9 (A and B) are protected against a short circuit by glass fuse.
In case of fuse damage, the replacement of the same parameters is required.
In case of overload, the output voltage is automatically shut off, and so is the LED indicator. The restoration of the
voltage takes place immediately after the failure (overload) is over.
4.2 Battery-assisted operation.
In case of a main power outage, the device is immediately switched into a battery-assisted operation.
The PSU is equipped with the discharged battery disconnection system. During the
battery-assisted operation, reducing voltage below 9,5V at the battery terminals will cause
battery disconnection.
4.3 Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the
power supply network. The PSU does not require performing any specific maintenance measures, however, in
case of significant dust rate, its interior is recommended to be cleaned with compressed air. In case of fuse
replacement, use a replacement of the same parameters.

www.pulsar.pl PSDCB18129B
8
WEEE MARK
According to the EU WEE Directive –It is required not to dispose of electric or
electronic waste as unsorted municipal waste and to collect such WEEE separately.
The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but recycled
according to the applicable law.
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [email protected], [e-mail]
http:// www.pulsar.pl, www.zasilacze.pl
GENERAL WARRANTY CONDITIONS
1. Pulsar (the manufacturer) grants a two-years warranty for the equipment, counted from the device’s production
date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the
manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects,
unless such defects have been reported within the warranty period (item 1).
3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main
office of the manufacturer.
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description
of the defect.
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest
convenienve, however not later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the
repairs, or if the equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.
7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer,
exclusively.
8. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment’s intended use
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical
agents,
- improper installation and configuration (in defiance with the manual),
9. The warranty is void in any of the following circumstances:
- construction changes
- repairs carried out by any unauthorized service center
- damage or removal of warranty labels
- modifications of the serial number
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined
according to the wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no reponsibility for the defects that result from:
- the damaging, malfunctioning or inability to operate the equipment
- defects that result from using the equipment outside its stated specifications and operating parameters failing to
abide by the recommendations and requirements contained in the manual, or the use of the equipment.