Pulsar PS701205 User manual

1
Enclosed switch-mode power supplies
PS401203, PS701205,
PS1001207, PS1501210
EN
Edition: 2nd from 15.11.2010
Supercedes edition: 1st from 17.07.2010
1. Technic l description.
1.1 Gener l ch r cteristics.
The power supply units are intended for the feeding of alarm system equipment which requires uninterruptible
supply of 12VDC voltage provided by 230VAC mains. Their design enables simple switching of the output voltage within
the range of 12÷15VDC using a potentiometer. The power supply units are protected against short-circuit overload and
overvoltage. The PS1501210 power supply unit is additionally equipped with thermal protection.
1.2 Technic l p r meters.
PS401203 PS701205 PS1001207 PS1501210
Dimensions (L x W x H) 129 x 98 x 40mm 160 x 98 x 39mm 199 x 98 x 39mm 199 x 99 x 50mm
Net/Gross weight
375g / 395g 475g / 500g 640g / 670g 730g/775g
Input volt ge 85 ÷ 264 V AC
120 ÷ 370 V DC
170 ÷ 264 V AC 170 ÷ 264 V AC 85 ÷ 264 V AC
120 ÷ 370 V DC
Le k ge current <0 7mA / 230 VAC <0 7mA / 230 VAC <0 7mA / 230 VAC <0 7mA / 230 VAC
Output volt ge 12 V ÷ 15V DC (12V factory settings)
Output power
40W 70W 100W 150W
Output current
for t
AMB
< 30°C
3 0 A* 5 0 A* 7 0 A* 10 0 A*
Output current
for t
AMB
= 40°C
2 1 A* 3 5 A* 4 9 A* 7 0 A*
Output ripple <100mV <100mV <100mV <100mV
Short circuit protection YES YES YES YES
Overlo d protection 110% - 150%
output power
110% - 150%
output power
110% - 130%
output power
110% - 130%
output power
Overvolt ge protection YES YES YES YES
Over temper ture
protection
NO NO NO YES
Oper tion conditions
0
o
C ÷ 40
o
C RH 20 ÷ 90 % no condensation
REMARKS - - - PFC
REMARKS:
Output current (*):
Maximum continuous output current depends of the ambient temperature – refer to graph 1.

2
Graph 1. Relation between ambient temperature and maximum continuous output current of the PSU.
2. Inst ll tion.
2.1 Requirements.
The power supply shall be mounted by the qualified installer having appropriate (required and necessary for a
given country) permissions and qualifications for connecting (operating) low-voltage installations. The unit shall be
mounted in closed rooms according to the environment class II of the normal air humidity (RH=90% max. without
condensation) and the temperature within the range from 0°C to +40°C.
The power supply shall be mounted in a close casing (a cubicle a terminal device) and in order to fulfill LVD and
EMC requirements the rules for power-supply encasing and shielding shall be observed according to application.
Due to the power supply design, the PE wire h s to be connected to the corresponding connector of the
supply unit. Oper tion without proper grounding of the power supply is not llowed!
2.2 Inst ll tion procedure.
1. Prior to inst ll tion of the power supply unit, m ke sure th t power le ds h ve been disconnected from the
230VAC m ins.
2. Install the unit in the previously selected place.
3. Connect the 230VAC power leads. Connect the PE cable (yellow-green) to an appropriate terminal on the power
supply unit (marked with ).
The circuit of the shock protection sh ll be performed with p rticul r c re, i.e. the yellow nd green
protection wire of the power c ble sh ll be connected from one side to the termin l m rked by the
symbol of in the c sing of the power-supply. Oper tion of the power-supply without the properly
m de nd fully oper tion l circuit of the shock protection is
UNACCEPTABLE!
It c n result in f ilure of devices nd electric shock.
4. Connect load/loads to proper output junctions of the power supply unit (positive end is marked as V+ negative end as
V-).
5. Upon the completion of tests and trial activation close the housing cabinet etc.

3
2.3 Connectors description.
PS401203 / PS701205 PS1001205 PSB1501210
Connectors/elements description:
Elements/termin ls Description
L, N, PE L-N - input voltage conectors 230 V AC
PE – protective conductor connector
V- Output ground (0V)
V+ Power supply output (+12V)
LED D1 Diode signals the presence of voltage at the unit’s output
P1 Potentiometer - output voltage adjust
2.4 L yout of ssembly openings.
The symbol of a threaded opening as presented in the figures below means that the opening in the unit's housing is of
the threaded type. The threaded openings are not of the pass-through type.
Fig. 1 L yout of ssembly openings for the PS401203 power supply unit.

4
Fig. 2 L yout of ssembly openings for the PS701205 power supply unit.
Fig. 3 L yout of ssembly openings for the PS1001207 power supply unit.

5
Rys. 5 L yout of ssembly openings for the PS1501210 power supply unit.
3. M inten nce.
All maintenance operations can be carried out only if the unit has been disconnected from the power network.
The unit does not require any particular maintenance. However clean with compressed air if heavily dusted.

6
WEEE designation
The waste electric and electronic equipment worn out may not be disposed of together
with standard household waste. According to the WEEE directive, applicable in the EU, the
separate neutralization methods should be used for electric and electronic equipment.
Puls r K.Bogusz Sp.j.
Siedlec 150 32-744 Łapczyca Poland
Tel. [phone] Fax. [phone]
e-mail: [email protected] [e-mail]
http:// www.pulsar.pl
THE GENERAL WARRANTY CONDITIONS
1. Pulsar K. Bogusz Particular Partnership (the manufacturer) provides a one-year quality warranty for devices as from the
purchase date placed on a purchase proof.
2. The warranty includes free repair or replace for a functional equivalent (the selection is performed by the manufacturer) of a
non-operational device due to reasons dependent on the manufacturer including production and material defects as far as
defects are notified within the warranty period (item 1 and 2).
3. The equipment subject to warranty shall be provided to the point where it has been purchased or directly to the place of
business.
4. The complete devices are subject to warranty and the sort of defect shall be described in written in a correctly fulfilled claim
notification.
5. If a claim is accepted the manufacturer is obliged to perform warranty repairs as soon as possible but no later than 14 working
days since the device is provided to the service of the manufacturer.
6. The repair period specified in item 5 can be extended if there are no technical opportunities to perform the repair or the
equipment is conditionally accepted by the service due to non-compliance of the warranty conditions by the person lodging a
claim.
7. All service actions related to warranty are performed exclusively at the service of the manufacturer.
8. The warranty does not include the following defects of the device due to:
- manufacturer-independent reasons
- mechanical defects
- improper storage and transport
- operation contrary to the instruction manual or purpose of the device
- emergencies including atmospheric discharges failures of the power network fire flood effect of high temperature and
chemical agents
- improper installation and configuration (contrary to the instruction manual)
9. The loss of rights resulting from the warranty always occurs if it is confirmed that construction changes have been performed or
repairs have not been performed at the service of the manufacturer or if serial numbers or warranty labels of the device are
somehow replaced or damaged.
10. The responsibility of the manufacturer towards the purchaser is limited to the value of the device determined according to the
wholesale price from the purchase day suggested by the manufacturer.
11. The manufacturer does not bear any responsibility for damages resulting from failure faulty operation or inability to use the
device particularly if it results from non-compliance with advices and requirements included in the instruction manual or contrary to
purpose of the device.
.