Pulsar SF116-B User manual

1
SF116-B
v1.2
SF116-B 16-ports switch with buffer power supply
for 16 IP cameras
Edition: 5 from 30.01.2019
Supercedes the edition: 4 from 23.11.2018 EN
Features:
Uninterruptible power supply PoE of 16 IP cameras
Switch 16 ports
16 PoE ports 10/100Mb/s, (1÷16 ports) (data and
power supply)
2 ports 10/100/1000Mb/s (ports G1/TP, G2/TP2)
2 ports 10/100/1000Mb/s SFP (port G1/SFP, G2/SFP)
30 W for each PoE port, supports devices complaint
with the IEEE802.3af/at (PoE+) standard
Approximate backup time: 2h
Supports auto-learning and auto-aging of MAC
addresses (16K size)
LED indication
Metal housing - color white RAL 9003, which
can accommodate four 7Ah/12V batteries
warranty –2 year from the production date
Example of use.
CONTENTS
1. Technical description
1.1 General description
1.2 Block diagram
1.3 Description of components and connectors
1.4 Technical parameters
2. Installation
2.1 Requirements
2.2 Installation procedure
3. LED indication of operating status
3.1 Operation indication of the switch.
4. Maintenance

2
1. Technical description.
1.1.General description.
The SF116-B switch is designed for uninterruptible power supply of 16 IP cameras (PoE).
The main elements of this system include:
- 16 ports PoE switch
- buffer power supply unit 54 V DC (PSB-3004850) which can accommodate four batteries connect in series (4x7 Ah/12 V)
In case of power decay, a battery back-up is activated immediately.
The approximate backup time is given assuming that all output ports are used (using typical devices and 7 Ah
batteries). The electricity consumption for own needs and the energy efficiency of the power intake track were taken into
account. The exact description of how to perform the calculations can be found at: "Approximate backup time - assumptions
for calculations".
Automatic detection of any devices powered in the PoE/PoE+ standard is enabled at the 1 –16 ports of the switch.
The G1/TP, G2/TP ports is used for connection of another network device via RJ45 connector. The switch is fitted with SFP
slots; the use of fiber optic module (GBIC) allows fiber optic transmission.
The LEDs at the front panel indicate the operation status (description in the table. 3).
The switch is housed in a metal enclosure (color RAL 9003) which can accommodate four 7 Ah/12 V battery
(connect in series). The enclosure features a micro switch tamper indicating door opening (front panel) - TAMPER.
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a
separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless
access point or router.
1.2. Block diagram.
Fig. 1. Block diagram.

3
1.3. Description of components and connectors.
Fig. 2. The view switch'a.
Table 1. (see Fig. 2)
Element no.
(Fig. 2)
Description
[1]
16-ports switch PoE
[2]
Switch mode buffer power supply unit 54 V DC PSB-3004850
[3]
L-N power supply connector 230 V, protective connector
[4]
B+, B- : battery output +BAT red, -BAT black
[5]
Space for four batteries (4x7 Ah/12 V)
[6]
TAMPER, terminals of tamper protectio (NC)
[7]
Green LED indicating voltage DC
Fig. 3. The view of the module switch'a.

4
Table 2. (see Fig. 3)
Component No
(Fig. 2)
Description
[1]
16 x PoE ports (1÷16) [RJ45]
[2]
2 x UPLINK ports (G1/TP, G2/TP) [RJ45]
[3]
2 x UPLINK ports (G1/SFP, G2/SFP) [SFP]
[4]
Yellow PWR LED indicating the supply voltage of the switch
[5]
LEDs:
PoE –indicating voltage at the PoE port
LINK/ACT –indicating the LAN connection status
[6]
Power socket switcha (DC INPUT)
1.4. Technical parameters
- parameters of the switch (tab.3)
- electrical parameters (tab.4)
- mechanical parameters (tab.5)
- operation safety (tab.6)
- operating parameters (tab.7)
Table 3. Parameters of the switch
Ports
16 x PoE (10/100Mb/s) (RJ-45)
2 x UPLINK (10/100/1000Mb/s) (RJ-45)
2 x UPLINK (10/100/1000Mb/s) (SFP)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802.3af/at (1÷16 ports), 54 V DC / 30 W at each port *
Used pairs 1/2 (+), 3/6 (-)
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth
14,8Gbps
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply
Link
PoE Status
*The given value of 30 W per port is the maximum value. The total power consumption should not exceed 192 W.
Table 4. Electrical parameters
Mains supply
~200-240 V; 50 Hz;
Current up to
1,3
Supply power
219 W
Output current at the PoE ports (RJ45)
16 x 0,6 A ƩI=4 A (max)
Output voltage at the PoE ports (RJ45)
44÷54 V DC
PSU current consumption
230 mA (max.)
Battery charge current
0,5A max. (+/-5%)
Approximate backup time
2h
Short-circuit protection SCP and overload
protection OLP
Electronic, automatic recovery
Battery circuit protection SCP and
reverse polarity connection
melting fuse
Deep discharge battery protection UVP
U<38V (± 5%) – disconnection of the batteries

5
Table 5. Mechanical parameters
Dimensions
W=525, H=540, D+D1=72+14 [+/- 2mm]
W1=530, H1=545 [+/- 2mm]
The dimensions of the battery
compartment
370x180x80 (WxHxD)
Gross/Net weight
10,1 / 11 kg
Enclosure
Steel plate, DC01 1,0mm color white RAL 9003
Closing
Cheese head screw x 2 (at the front)
Connectors
Power supply of the cameras: RJ45 socket
Battery output BAT: 6,3F-2,5
TAMPER output: wires
Table 6. Operation safety
Protection class PN-EN 609501:2007
I (first)
Protection grade PN-EN 60529: 2002 (U)
IP20
Electrical strength of insulation:
- between input and output circuits of the PSU
- between input circuit and PE protection circuit
- between output circuit and PE protection circuit
3000 V AC min.
1500 V AC min.
500 V AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500 V DC
Declarations, warranty
CE, 2 year from the production date
Table 7. Operating parameters
Operating temperature
-10ºC...+40ºC
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106
2. Installation.
2.1. Requirements.
The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal
relative humidity (RH=90% maximum, without condensation) and temperature from -10°C to +40°C. Ensure the free flow
of air around the unit. The PSU shall work in a vertical position that guarantees sufficient convectional air-flow through
ventilating holes of the enclosure. It is required to install an installation switch with a nominal current of min. 3 A in the
power supply circuits outside the power supply unit.
The switch load balance should be done before installation. The given value of 30 W per port is the maximum value
referring to a single output. The total power consumption should not exceed 192 W. The increased demand for power is
particularly evident in the case of cameras with heaters or infrared illuminators - when launching these features, the
power consumption increases rapidly, which may adversely affect the operation of the switch. As the device is designed for
a continuous operation and is not equipped with a power-switch, therefore an appropriate overload protection in the power
supply circuit should be provided. The electrical system shall be made in accordance with applicable standards and regulations.
2.2. Installation procedure
Before installation, cut off the voltage in the 230 V power-supply circuit.
To switch power off, use an external switch, in which the distance between the contacts of all
poles in the disconnection state is not less than 3mm.
2. Mount the PSU in a selected location and connect the wires.
3. Connect the power cables (230 V) to L-N clips of the PSU.

6
The shock protection circuit shall be performed with a particular care, i.e. the yellow
and green wire coat of the power cable shall stick of the terminal - marked with ‘ ‘
symbol on the PSU enclosure. Operation of the PSU without the properly made and
fully operational shock protection circuit is UNACCEPTABLE! It can cause a device
failure or an electric shock.
4. Connect the ground wire to the terminal marked with the symbol (power supply module connector). Connect the
ground wire to the clip marked by the earth symbol PE. Use a three-core cable (with a yellow and green protection
wire) to make the connection. Lead the cables to the appropriate clips through the insulating bushing of the connection
board.
5. Connect the power (230 V).
6. Connect the batteries in series/parallel to the BAT terminals:
- battery output (+): BAT+ cable / red,
- battery output (-): BAT –cable / GND / black.
Caution! Connect four 7Ah/12V batteries in series
7. Connect the camera cables to the RJ45 connectors
(PoE connectors –sockets RJ45 from 1 to 16).
8. Connect the remaining LAN devices to RJ45 or SFP connectors
(using a GBIC)
(G1/TP or G1/SFP and G2/TP or G2/SFP)
CAUTION! G1/TP and G1/SFP connectors can not operate simultaneously
CAUTION! G2/TP and G2/SFP connectors can not operate simultaneously
9. Connect the recorder to the switcha.
10. Check the optical indication of the switch operation.
11. After installing and checking proper working, the enclosure can be closed.
Connection schemes
3. Operation indication
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY
YELLOW LED LIGHT (Power)
Indication of the switch's power
supply
OFF –no power supply of the switch
ON –power supply on, normal operation
OPTICAL INDICATION AT THE PoE PORTS (1÷16)
YELLOW LED LIGHT (LINK/ACT)
The connection status of LAN devices,
10MB/s or 100Mb/s
and data transmission
OFF- no connection
ON - the device is connected; 10Mb/s or 100Mb/s
Blinking –data transmission
GREEN LED LIGHT (PoE)
Indication of the PoE
power supply
at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant with
the IEEE802.3af/at standard)
ON –supply
Blinking –short-circuit or output overload

7
RED LED:
on –the PSU is supplied with 230 V
off –no 230 V supply
GREEN LED:
on –DC voltage in the output of the PSU
off –no DC voltage in the output of the PSU
OPTICAL INDICATION AT THE UPLINK PORTS (G1/TP, G2/TP, G1/SFP, G2/SFP)
GREEN LED LIGHT
No light (OFF) - no connection or LAN device is not connected
ON - LAN device connected (port busy, do not connect the device)
Blinking –data transmission (do not connect the device, even if the slot is empty)
CAUTION! G1/TP and G1/SFP sockets can not operate simultaneously
CAUTION! G2TP and G2SFP sockets can not operate simultaneously
3.1. Operation indication of the switch.
The PSU is equipped with two diodes on the front panel:
Installation example of the SF116-B with batteries
(accumulators are not included)
4. Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the power
supply network. The PSU does not require performing any specific maintenance measures, however, in case of
significant dust rate, its interior is recommended to be cleaned with compressed air.

8
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment should be
disposed of separately from normal household waste.
CAUTION! The power supply unit is adapted for cooperation with the sealed lead-acid batteries (SLA). After the operation period they must not be
thrown but recycled according to the applicable law.
Pulsar sp. j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], [e-mail]
http:// www.pulsar.pl, www.zasilacze.pl