Pulsar Z021 User manual

CAL. Z021
CHRONOGRAPH
ENGLISH
lAnalogue & digital time displays
l Daily alarm and hourly chime
l Stopwatch
l Selection of 12- or 24-hour format
l EL backlight
NPSC47_E.indd 1 13/06/14 9:55

English
English
32
DISPLAY AND CROWN/BUTTONS
b: Extended position
a: Normal position
Hour hand
Minute hand
Second hand
CROWN
Date
a b
Month
Day of the week
Hour Minute Second
Start/Stop
Reset
Light
Mode
ILLUMINATING LIGHT (EL BACKLIGHT)
•The electroluminescent panel loses its
luminance as the battery voltage gets lowered.
Also, its luminance level decreases gradually
with use.
•When the illuminating light becomes dim,
replace the batteries with new ones.
A
B
D
C
CWith each press, the mode in the digital display changes in the
following order.
NORMAL TIME
mode
STOPWATCH
mode
ALARM
mode
TIME SETTING
mode
DPress in any mode to turn the illuminating light on.
NPSC47_E.indd 2-3 13/06/14 9:55

English
English
54
SCREW DOWN CROWN
[for models with screw down crown]
Locking the crown
1Turn Crown counterclockwise until you no
longer feel the threads turning.
2Crown can be pulled out.
1Push Crown back in to normal position.
2Turn Crown clockwise while pressing it
lightly until tight.
Unlocking the crown
TIME/CALENDAR MODE
• Theanalogueanddigitaldisplaysareseparatelyillustratedinthefollowingsections
ofthismanual.
CROWN
Pull out when the second hand is at
the 12 o'clock position.
The second hand will stop on the spot.
Turn to set the hour and minute
hands to the correct time.
Push back simultaneously with a time
signal.
ANALOGUE TIME SETTING
NPSC47_E.indd 4-5 13/06/14 9:55

English
English
76
DIGITAL TIME/CALENDAR SETTING
CPress until the watch enters the TIME
SETTING mode.
• Tosettheseconddigits,ifyoupresstheButtonAwhiletheseconddigitscount
any number between “30” and “59,” one minute is added and the seconds digits
are immediately reset to “00.” IfyoupresstheButtonAwhiletheseconddigits
count any number between 00 and 29, the second digits will be reset to 00 and
the minute digits will be unchanged.
• Inthehoursetting,"H"appearstoindicatethe24-hourformat,"A"or"P"appears
toindicatethe12-hourformat.
Press to select the item to be
adjusted. With each press of the
button, the selected item changes in
the following order.
B
Second Hour Minute
Month
Day of week
12-/24-hour format
APress to set the ashing digits.
CPress to conrm the settings and
return to the NORMAL TIME mode.
Date
NPSC47_E.indd 6-7 13/06/14 9:55

English
English
98
ALARM
CPress until the watch enters the
ALARM mode.
BPress to show the ALARM SETTING
display.
The hour digits start flashing.
APress to set the ashing digits.
CPress to conrm the alarm settings
and return to the NORMAL TIME
display.
Press to select the item to be
adjusted.
Hour Minute
B
Engagement/disengagement of the alarm
With each press of the Button A in the ALARM setting mode, the alarm
and chime will be alternately engaged or disengaged in the following
sequence. The alarm indicator and chime indicator will appear or
disappear accordingly on the display.
How to stop the alarm manually while it is sounding
 To stop the alarm manually while it is sounding, press either Button A or
Button B.
Snooze function
Press the Button C to turn the snooze function on or off alternately.
When the snooze function is enabled, the alarm will stop sounding
temporarily and go off again 5 minutes later for 20 seconds and
automatically stop.
NPSC47_E.indd 8-9 13/06/14 9:55

English
English
1110
STOPWATCH
lThe stopwatch measures up to 23 hours 59 minutes and 59 seconds in
1/100-second increments.
Start/Stop/Restart
Split/Reset
Split time measurement
START SPLIT SPLIT RELEASE STOP RESET
A
s
s
s
s
B
A
BB
• Measurementandreleaseofthesplittimecanberepeatedasmanytimes
asnecessarybypressingthebuttonB.
Standard measurement
A
s
s
B
A
START STOP RESET
A
B
CPress until the watch enters the STOPWATCH mode.
NPSC47_E.indd 10-11 13/06/14 9:55

English
English
1312
BATTERY CHANGE
Battery life : Approx. 2 years
Battery : SEIKO SR626SW, 1 piece
(for analogue display)
SEIKO CR2025, 1 piece
(for digital display)
2
Years
lIfthestopwatchisusedformorethan60minutesaday,thebatterylifemaybeless
than the specified period.
lEven ifeither ofthe two batterieshas run down, replaceboth batteries withnew
ones.
l
Asthebatteryisinsertedatthefactorytocheck thefunctionandperformanceof
the watch, its actual life once in your possession may be less than the specied
period.
lWhen the batteries expire, replace them as soon as possible to prevent any mal-
function.
lWe recommend that you contact an AUTHORIZED PULSAR DEALER for battery
replacement.
WARNING
lDo not remove the battery from the watch.
lIf it is necessary to take out the battery, keep it out of the reach of
children. If a child swallows it, consult a doctor immediately.
lNever short-circuit, tamper with or heat the battery, and never ex-
pose it to re. The battery may burst, become very hot or catch re.
CAUTION
l The battery is not rechargeable. Never attempt to recharge it, as this
may cause battery leakage or damage to the battery.
NPSC47_E.indd 12-13 13/06/14 9:55

English
English
1514
TO PRESERVE THE QUALITY OF YOUR WATCH
WATER RESISTANCE
lNon-water resistant
lWater resistance (5 bar)*
If “WATER RESISTANT 5 BAR”
is inscribed on the case back,
your watch is designed and
manufactured to withstand up
to 5 bar and is suitable for swimming, yachting
and taking a shower.
If “WATER RESISTANT 10 BAR”,
“WATER RESISTANT 15 BAR” or
“WATER RESISTANT 20 BAR” is
inscribed on the case back, your
l
Water resistance (10 bar/15 bar/20
bar)*
watch is designed and manufactured to withstand
up to 10 bar/15 bar/20 bar and is suitable for taking
a bath, shallow diving, but not for scuba diving.
We recommend that you wear a PULSAR Diver’s
watch for scuba diving.
If “WATER RESISTANT” is not
inscribed on the case back, your
watch is not water resistant, and
care should be taken not to get
If “ WATER RESISTA NT ” is
inscribed on the c ase back,
your watc h is design ed a nd
manufactured to withstand up
to 3 bar, such as ac cidental
contact with splashes of water or rain, but it
is not designed for swimming or diving.
lWater resistance (3 bar)
it wet as water may damage the movement. If
the watch becomes wet, we suggest that you
have it checked by an AUTHORIZED PULSAR
DEALER or SERVICE CENTER.
* Beforeusingthe waterresistance5, 10, 15or20 barwatchin water,besurethe
crown is pushed in completely.
 Donotoperatethecrownwhenthewatchiswetorinwater.Ifusedinseawater,
rinsethewatchinfreshwateranddryitcompletely.
* Whentakingashowerwiththewaterresistance5barwatch,ortakingabathwith
thewaterresistance10,15or20barwatch,besuretoobservethefollowing:
• Donotoperatethecrownwhenthewatchiswet.
• If the watch is left in warm water, a slight time loss or gain may be caused.
This condition, however, will be corrected when the watch returns to normal
temperature.
NOTE:
Pressure in bar is a test pressure and should not be considered as
corresponding to actual diving depth since swimming movement tends
to increase the pressure at a given depth. Care should also be taken on
diving into water.
TEMPERATURES
5
5
50° C (122° F) may cause battery
leakage or shorten the battery life.
Your watch works with
stable accuracy within a
temperature range of 5° C
and 35° C (41° F and 95° F).
Temperatures over
Do not leave your watch in very low
temperatures below –5° C (+23° F)
for a long time since the cold may
cause a slight time loss or gain.
However, the above conditions will
be corrected when the watch returns
to normal temperature.
NPSC47_E.indd 14-15 13/06/14 9:55

English
16
MAGNETISM
Your watch will be
adversely affected by
strong magnetism. Keep
it away from close contact
with magnetic objects.
Be careful not to expose
the watch to solvents,
mercury, cosmetic spray,
detergents, adhesives
or paints. Otherwise,
CHEMICALS
the case, bracelet, etc. may
become discolored, deteriorated or
damaged.
Light activities will not
affect your watch, but be
careful not to drop your
watch or hit it against
hard surfaces, as this
SHOCKS & VIBRATION
may cause damage.
To prevent possible rusting of
the case and bracelet caused by
dust, moisture and perspiration,
wipe them periodically with a
soft dry cloth.
CARE OF CASE AND BRACELET
It is recommended that the
watch be checked once
every 2 to 3 years. Have
your watch checked by an
AUTHORIZED PULSAR
PERIODIC CHECK
DEALER or SERVICE CENTER to
ensure that the case, crown, buttons,
gasket and crystal seal remain intact.
PRECAUTION REGARDING
CASE BACK PROTECTIVE FILM
If your watch has a
protective film and/or a
sticker on the case back,
be sure to peel them off
before using your watch.
NPSC47_E.indd 16 13/06/14 9:55