PULSEEIGHT P8-HDBT-L-EXSET User manual

CHECK WHAT’S INSIDE THE BOX
IMPORTANT!
• 1 x neo:Lite PoH Receiver
• 1 x neo:Lite Transmitter
• 1 x IR Blaster Cable Pack
• 1 x Quick Start Guide
• 1 x Power Supply Adapter
• Please read the instructions before attempting to install or operate this equipment.
• Visit the help.pulse-eight.com to download the latest product manual, additional documentation, and
conguration tools.
!
This installation guide helps you to install and use your Pulse-Eight neo:Lite
HDMI Extender for the rst time.
Go to help.pulse-eight.com for additional information on this product including
important technical information not provided in this document and warranty
terms & conditions.
SCAN FOR HELP
QUICK START GUIDE
neo:Lite HDMI Extender Set (P8-HDBT-L-EXSET)

HDBaseT Input - Connect the appropriate category cable (Cat 5e or higher recommended) to the input of the
receiver; this cable should also be connected to the HDBaseT output on the neo:Lite transmitter.
IR Receiver (RX) - The IR Receiver port (black) can be used to distribute IR signals back to the attached neo:Lite
transmitter, when connecting an IR Receiver.
HDMI Output - Connect the appropriate high speed HDMI cable to this port and connect to the sink device.
IR Flasher (TX) - The IR Flasher port (grey) is used to control the connected HDMI Sink device (TV) using the
IR transmitter.
A
B
C
D
48 V Power Input - is used with the supplied 48V power adapter
HDBaseT Output - Connect the appropriate category cable (Cat 5e or higher recommended) to the output of
the transmitter; this cable should then be connected to the HDBaseT input on the neo:Lite receiver. The LEDs
will illuminate to indicate a link is established (amber LED) and video (green LED) is being sent.
IR Receiver (RX) - The IR Receiver port can be used to distribute IR signals to the attached neo:Lite receiver,
when connecting an IR Receiver.
HDMI Input - Connect the appropriate high speed HDMI cable to this port and connect to the source device.
IR Flasher (TX) - The IR Flasher port is used to control the connected HDMI Source device (eg: Blu-ray) using
the IR transmitter.
A
B
C
D
E
1. Connect HDMI cable from your video source (e.g. Blu-Ray player) to the HDMI input of the neo:Lite transmitter.
2. Connect the appropriate category cable (Cat 5e or higher recommended) to the neo:Lite Transmitter’s ‘HDBaseT
Out’ ports.
3. Complete the connection by attaching the other end of the Cat cable to the neo:Lite Receiver’s ‘HDBaseT In’ port
4. Connect HDMI Out on the neo:Lite Receiver to the sink device (i.e. TV) using a high-speed HDMI cable.
5. If required, connect the compatible IR Flasher (Emitter/Transmitter) cable to the ‘TX’ port on the neo:Lite Transmitter
and the IR bud placed over the source device’s IR window.
6. If required, connect the IR Receiver to the neo:Lite Receiver’s ‘RX’ port - and place the IR bud on the underside of
the sink device (i.e. TV).
7. Insert the supplied power adapter to the neo:Lite Transmitter and plug it into the AC mains.
8. Turn ON the AC mains.
9. As it powers ON, check the LED status on the attached neo Receiver to ensure correct installation and connection.
Note: The Green LED of the HDBaseT port (RJ45) on the neo Receiver should illuminate when there is video to the device .
INSTALLATION
PANEL DESCRIPTIONS
neo:Lite Transmitter
neo:Lite Receiver

FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Pulse-Eight Limited, 8-12 Alder Hills, Poole, Dorset, BH12 4AL. UK
[e-mail] | www.pulse-eight.com | [phone]
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer le,
in any form or by any means (electronic, mechanical, magnetic, optical, chemical, manual, or otherwise) without express written permission and consent from the
manufacturer.
© Copyright 2023. All Rights Reserved. Version 2.0 - June 2023
SAFETY PRECAUTION
Please read the full manual instructions before attempting to install or operate this equipment.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock, and injury.
• To prevent re or shock hazards, do not expose the unit to rain, or moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Where possible, install the extender towards the top of the rack to avoid the unit overheating.
• Only use the supplied IEC cable.
• Never push any objects into this product through any openings or empty slots in the unit as you may damage parts inside
and/or cause an electrical shock.
• Do not allow anything to rest on the power cabling and avoid putting the weight of any kind on it.
• To protect the unit from overheating do not block any vents or openings in the unit housing that provides ventilation. Allow
sufficient space for air to circulate around the unit.
• This product is intended for use in a clean (dust-free) residential environment.