Pump Alarm Cellular Alarm Instruction Manual

Quick Start Installation Guide
Copyright 2017, PumpAlarm.com, All Rights Reserved
Cellular Alarm

Please scan the image on the right with your
smartphone to view our installaon video, or
simply visit the link below.
www.pumpalarm.com/installaon
Need more guidance?
For technical support please call : 1-888-454-5051
Hours: M-F 8a-5p EST
The following items are available to you at pumpalarm.com:
• In Depth User Manual
• Installaon Video
• How it Works Video
• Online Store (where you can buy addional units and accessories)
PumpAlarm.com
203 W Morris St.
Indianapolis, IN 46225
888-454-5051

Components:
1. Cellular Alarm Unit
2. Hose Clamps (2)
3. Mounng Straps (4)
4. AA Baeries (4)
Oponal Sensors :
A. Water Sensor
B. Tilt Switch
C. Single Float Switch
D. Dual Float Switch
*See PumpAlarm.com for our
most up-to-date list of sensors.
Missing or Damaged Components?
Call PumpAlarm.com
888-454-5051
M-F 8:00a-5:00p EST
Do not return product to retail locaon.
1. 2.
3.
A. B. C. D.
4.

1. Status Light - Indicates the cellular status of your unit. Refer to the online manual
at pumpalarm.com for a descripon of the blink paerns.
2. Low Baery and Temperature Light - 2 red blinks indicates the backup baeries
are low. If the red light is ashing it indicates the baeries are crically low. When
the green light is ashing it indicates the Temperature Alarm. Refer to the online
manual at pumpalarm.com for a descripon of the blink paerns.
3. ON/OFF/MUTE - Press the buon 1 me to mute the device and 1 me to unmute
the device. Press and hold for 3 seconds to ON/OFF.
4. PUSH TO TEST - Press the buon 1 me to test device and receive a text message.
Hold the Test Buon to congure. Tap the Test Buon to test.
5. Input LEDs: 1 - 2 - LEDs blink when the associated inputs 1 and 2 are triggered.
6. Input LEDs: 3 - 4 - #3 input LED blinks when the lower oat is triggered and #4
blinks when the upper oat is triggered.
7. Sensor Input Connectors -
A. Inputs 1 and 2 are 2-pin, dry contact closure. Can be customized for
Normally Open or Normally Closed.
B. Inputs 3 and 4 are ed together as a 3-pin, for use with our dual oat and
sewage oat.
Geng to Know Your Device:

1
2
3
4
5
7A
67B
7
Unit Label

Mount the Cellular Alarm to a wall or pipe. Use mounng template below. It is the
correct dimensions for mounng the product. Mark the points using a pencil, then
use a 3/16” drill bit to make your holes. Apply the red anchors, and screws. Place
Cellular Alarm on the wall.
4.56”
xx
Mounng Template
Mounng Hardware and Sensors

Mount the device to a pipe using the mounng brackets (hose clamps).
Hose Clamps
Connect your choice of sensor into one of the inputs on the boom of the unit. We
recommend using the oat switch, or dual oat switch for sump pump applicaons
and the digital water sensor for oor or drain applicaons.

Please acvate your unit. Visit : www.pumpalarm.com/acvate.
Enter the 6 digit alphanumeric unit number found on the side of the unit. Then your
billing informaon.
This generates the phone number for your unit as well. Save this phone number as a
contact in your phone.
Install (4) AA baeries by opening the baery door on the back of the unit. Align the
negave (-) end of the baery to the spring in each holder.
Activate Online
www.pumpalarm.com/activate
PumpAlarm.com/activate
Phone #: [phone]
add
photo
Cellular Alarm
Last
Company
Mobile
iPhone
[phone]
Side of Unit
UNIT
ID 123ABC
1Unit Acvaon and Power On
AInstall Baeries

Plug the device into a 110V A/C outlet to power your unit on. Once the status light
turns solid green, press and hold the “Push to Test/Hold to Congure” buon for 3
seconds. Unit will chirp twice and status light will blink red & green. This will get the
unit ready to receive text messages from your cell phone. In the next step, you will
congure the unit by sending it text message commands.
Solid Green Light
BPower Device On
Caller ID and Conguraon Mode
If no phone numbers are configured in the unit, it will accept commands from any
phone number. Once a phone number is configured in the unit, only commands
from phone numbers configured in the unit will be processed.
The unit can be placed in Config Mode by pressing and holding the Mute button
until the status light (top light) changes to red/green blinking. This allows the device
to accept commands from any phone.

Using your mobile phone, create and send a text message to your device. Xis either
1,2, or 3for which phone number slot you would like to fill.
If you want text messages sent to addional phones, repeat this process. Your device
can hold up to three phone numbers.
phoneX [Phone Number]
Space
Adding phone numbers
Phone[phone]
2
A
Seng up Contact Phone Numbers
Adding phone numbers
Phone[phone]
For your main number, which
is phone1, you will send the
following message; replacing
5557654321 with your mobile
phone number.