Pure Aqua WS1TC Assembly instructions

TO SET CURRENT TIME OF DAY:
PRESS SET HOUR AND USING UP OR DOWN ARROW BUTTONS, ADJUST
TO CURRENT HOUR.
PRESS SET HOUR AND USING UP OR DOWN ARROW BUTTONS, ADJUST
TO CURRENT MINUTES TO THE HOUR.
PRESS: SET HOUR BUTTON TO RETURN TO NORMAL SERVICE MODE.
TO BACKWASH IMMEDIATELY:
PRESS UP AND DOWN ARROW BUTTONS TOGETHER AND HOLD FOR 3
SECONDS -BACKWASH WILL START IMMEDIATELY.
TO BACKWASH WITHIN 24 HOURS AT THE PRESET TIME OF DAY:
PRESS UP AND DOWN ARROW BUTTONS TOGETHER AND RELEASE -
BACKWASH WILL START AT THE PREPROGRAMMED TIME.
NOTE: "SET HOUR" IS NOW "SET"

TO ENTER BASIC PROGRAMMING MODE:
PRESS: SET HOUR & UP ARROW BUTTONS TOGETHER FOR 3 SECONDS
USE UP OR DOWN ARROW BUTTONSTO SET THE PREFERRED HOUR
FOR THE START OF BACKWASH (DEFAULT = 2:00 AM)
PRESS: SET HOUR BUTTON
USE UP OR DOWN ARROW BUTTONSTO SET THE PREFERRED MINUTE
FOR THE START OF BACKWASH (DEFAULT= 2:00 AM)
PRESS SET HOUR BUTTON: USEUP OR DOWN ARROW BUTTONS TO
SELECT THE FREQUENCY BETWEEN BACKWASHES IN DAYS. (DEFAULT =
7DAYS)
TO ENTER MASTER PROGRAMMING MODE:
PRESS: SET HOUR & UP ARROW BUTTONS TOGETHER FOR 3 SECONDS
AND RELEASE
PRESS: SET HOUR & UP ARROW BUTTONS TOGETHER AGAIN FOR 3
SECONDS
USE UP OR DOWN ARROW BUTTONS TO CHOOSE:
P7: MINIMAL BACKWASH
P8: STANDARD BACKWASH (DEFAULT SETTING)
P9: EXTENDED BACKWASH
PRESS: SET HOUR BUTTON; CHOOSE “99”
PRESS: SET HOUR BUTTON; CHOOSE “60”
PRESS: SET HOUR BUTTON; CHOOSE “dp” WITH ARROW POINTED AT
“REGEN HOUR”
PRESS SET HOUR BUTTON TO RETURN TO NORMAL SERVICE MODE

INSTALLATION AND PROGRAMMING PROCEDURES
INSTALLATION AND STARTUP
1. System should installed by a licensed contractor, complying with all local and
federal codes and using quality materials to insure proper operation.
2. Install system. Be certain the inlet and outlet are properly connected.
3. Place bypass valve in “Bypass Position” with valve handles perpendicular to
the inlet and outlet.
4. Fully open the *test spigot (if installed) at the outlet of the system, or open a high
flow COLD water fixture, like a tub. DO NOT use any other water in house at this
time, including hot water and toilets. *Does not apply if using test spigot.
5. Place bypass valve into “Service Position” with valve handles parallel to each
other and the inlet and outlet.

6. Allow water to run through the open fixture or test spigot for 15-20 minutes
Observe the water flow for color. If after 20 minutes color from the media
is still present, allow system flow to continue until clear.
7. Close fixture or test spigot to stop water flow.
8. Initiate Manual Backwash of the CrystalClear Interior.
9. Observe visually and/or audibly the Backwash Flow (Cycle 1) for any reduction
of flow to drain. Backwash should maintain constant flow and sound.
10. If the backwash flow starts strong but diminishes start a new manual
backwash and allow backwash to complete and system to return to
service mode automatically.
11. If backwash flow is normal, allow the backwash process to complete
automatically.

12. If reduction in backwash flow is observed, repeat steps 5 through 10 until
backwash operates normally.
13. Finally, fully open a cold-water fixture and insure service flow is adequate.
14. If a reduction in service flow is observed, repeat steps 5 through 10 until
household service flow is normal.
15. With backwash and service flow adequate, set time of day on the control
valve by using the up and down buttons. Installation and verification are
complete.
Notes:
A. Check static (no water flowing) water pressure in pounds per
square inch (psi) using an accurate gauge, as close to the water
main as possible. Water pressure less than 40 psi may present
problems with the Healthy Home service flow, and compromising
the backwashing capability of the system.
B. Any addition to household plumbing can cause a drop in pressure
and/or flow rates. Great care has been taken in the design of the
Healthy Home to minimize these affects.