PureLink PureTools PT-CON-WP8B User manual

User Manual
PT-CON-WP8B
User Manual
Control Programmable Control Panel
Model PT-CON-WP8B
Designed in Germany
© 2018 PureLink GmbH All rights reserved. V1.0

User Manual
PT-CON-WP8B
Preface
Read this user manual carefully before using the product. Pictures shown in this
manual are for reference only. Different model layouts and specifications are subject
to the physical product.
This manual is for operation instructions only, not for any maintenance usage.
In the constant effort to improve our product, we reserve the right to make changes in
functions or parameters without prior notice or obligation.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of this
publication may be copied or reproduced without the prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. It has been tested
and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in
which case the user at their own expense will be required to take whatever measures
may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.
REACH | 1907/2006/EU
ROHS | 2011/65/EU
PureLink hereby declares that this product PureTools PT-CON-WP8B complies with Directives
1907/2006/EU and 2011/65/EU.

User Manual
PT-CON-WP8B
EMC / LVD (Electro Magnetic Compatibility /
Low Voltage Directive)
PureLink GmbH hereby declares that this product PureTools PT-CON-WP8B
complies with Directives 2014/30/EU and 2014/35/EU. The full text of the EU
Declaration of Conformity is available at the following Internet address:
http://www.purelink.de/ce/4251364716038_CE.pdf

User Manual
PT-CON-WP8B
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before
using the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing
material for possible future shipment.
Follow basic safety precautions to reduce the risk of fire, electrical shock and
injury to persons.
Do not dismantle the housing or modify the module. It may result in electrical
shock or burn.
Using supplies or parts not meeting the specifications of product may cause
damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or
install this product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment
damage. If an object or liquid falls or spills on to the housing, unplug the
module immediately.
Do not twist or pull by force ends of the optical cable. It can cause
malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the
power to the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

User Manual
PT-CON-WP8B
Table of Contents
1. Product Introduction ..................................................................................................................1
1.1 Features ..............................................................................................................................1
1.2 Package List .......................................................................................................................2
1.3 Installation .........................................................................................................................2
2. Panel Description........................................................................................................................3
2.1 Front Panel.........................................................................................................................3
2.2 Side Panel...........................................................................................................................4
2.3 Rear Panel...........................................................................................................................5
3. System Connection.....................................................................................................................7
3.1 System Diagram................................................................................................................7
3.2 Connection of Programming and Looping .................................................................8
4. System Operation..................................................................................................................... 10
4.1 USB Driver Installation................................................................................................. 10
4.2 Software Programming ................................................................................................ 10
4.2.1 Main Menu........................................................................................................... 12
4.2.2 Panel/Key Setting.............................................................................................. 15
4.2.3 Action List............................................................................................................ 19
4.2.4 Event Setting....................................................................................................... 20
4.2.5 Event List ............................................................................................................. 34
5. Specification.............................................................................................................................. 35
6. Panel Drawing........................................................................................................................... 36
7. Troubleshooting & Maintenance.......................................................................................... 37
8. After-Sales Service................................................................................................................... 37

User Manual
PT-CON-WP8B
1
1. Product Introduction
The programmable control panel is a Wall Control Panel. Every button is
programmable and works either individually or together. The programmable control
panel is built in the programmable 3 RS232, 1 RS485, 3 Infrared & 2 Relay, and 1
mini USB for programming.
Please notice, RS232 (1) and IR2 share the same port, cannot be used at the same
time. Also, RS232 (2) and IR3 share the same port, cannot be used at the same time.
It can fully control our product, as well as third party devices such as projectors,
screens etc. It is an easy-to-use control device for presentation show rooms,
classrooms and boardrooms.
1.1 Features
Every button can be programmed to send the bi-direction RS232 and RS485
commands simultaneously to control third party devices.
Every button can be programmed to send the infrared code, control the relay, to
let them work simultaneously to control the third party devices.
Every button is built in the infrared code and RS232 code learning function, and
baud-rate setting.
ID looping function. 99pcs programmable control panels can be looped and
controlled together, by ID identifying.
Programmed by USB or RS232, working with the PC software (PS-WP).
Crystal and backlit buttons with easy user-friendly customizable changeable
labels.
The backlit brightness is controllable.
Dimension: 11.4cm long and 7cm wide.

User Manual
PT-CON-WP8B
2
1.2 Package List
1 x Programmable Control Panel
1 x Power Adapter (12V DC)
3 x 2-pin Captive Screw Connector
2 x IR Emitter
8 x Button Caps
1 x Button Label
1 x USB Converting Cable
1 x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.
1.3 Installation
Follow the steps to install the device:
Firstly, dig a hole on the desk to the size marked on the aperture paper (shown in
Figure 1-1).
Secondly, put the device into the hole and adjust it to flush with the table (shown in
Figure 1-2).
Then, plug a set screw into the fixing mounting and screw the nuts tightly.
Aperture paper
Installation Guide

User Manual
PT-CON-WP8B
3
2. Panel Description
2.1 Front Panel
Crystal and luminescent, programmable buttons:
Every button can be programmable with the software PS-WP.
Connect the PC via USB or RS232.
And every label inside the button can be changeable. You can choose the label you
need and change it very easily like below:
(For the specific transparent paper table, please contact the local distributor or
reseller for it)

User Manual
PT-CON-WP8B
4
2.2 Side Panel
Note: When use this USB port to program the control panel’s buttons, the available
COM port number should not be more than 10.
Mini USB Connector:
1) Communicate with PC
which uses PS-WP to
program the buttons.
2) Transmit the infrared
data when learning IR
(Optional).
Infrared sensor port:
receive and learn the IR
code, to build the IR
database.

User Manual
PT-CON-WP8B
5
2.3 Rear Panel
The programmable control panel has various ports in the rear panel, including
Lopping port, RS232 port, RS485 port, IR port, Relay port and Power port. Below is
the introduction:
①Power connector: 12VDC. Be sure that the “+” and “-” never be mixed or
wrong connection.
②Low-Voltage relay ports: set the relay on/off by software PS-WP.
③This port includes: RS232 (1)/IR2, IR1 and RS485.
RS232 (1)/IR2: share the same port, the detailed use depends on the setting
of PS-WP. When be used as RS232, it is unidirectional transmission, transmit
data but without receive.
IR1: for control other devices, it can be programmable by the PS-WP.
RS485: the RS485 can be programmed as different commands and control
the device with RS485 port. The command of RS485 is the same as RS232
(1).
①
④
③
②

User Manual
PT-CON-WP8B
6
④This port includes two parts:
One part is RS232 (2)/IR3, it can be used for control other devices or looping
output. RS232 (2) and IR3 share the same port, the detailed use depends on
the setting of PS-WP.
Other part is RS232 (3), it can be used for control other devices or looping
output, or connect with PC.
These two parts share the same grounding.

User Manual
PT-CON-WP8B
7
3. System Connection
3.1 System Diagram
The programmable control panel can active different ports at one time. It means
every button can send the RS232 and RS485 commands, IR code and control the
relay at the same time. The demo system diagram as below:

User Manual
PT-CON-WP8B
8
3.2 Connection of Programming and Looping
The programmable control panel can be connected to the computer for
programming, to default the functions of every button. It can be connected by USB
or RS232, working with the PS-WP software. It is shown as below:
Programming Connection
Several pieces programmable control panels can be also looped to be a system, for
control more devices. It is looped by the inter RS232 setting. Please check the demo
picture as below:

User Manual
PT-CON-WP8B
9
Several programmable control panels Looping connecting
After connect the programmable control panels as above, and then we should set
the ID of each programmable control panel by PS-WP. The ID number is from 01 to
99, and it also is the class of the programmable control panel in the loop, different
programmable control panels should set to different ID. After connections finish, we
can set the control modes by PS-WP. For detailed connecting, please check the
picture below:
Detailed looping connecting
Note: Up to 99 programmable control panels can be looped within one system.
However, to achieve normal interaction, loop less programmable control panels (10
tops) in the system.
First class
Second class
Last class …

User Manual
PT-CON-WP8B
10
4. System Operation
4.1 USB Driver Installation
There are USB driver file and PS-WP software in the disk. The PS-WP can run directly
without installation.
But when connect the programmable control panel with PC by USB, it may need to
install the USB driver. Use the driver file to install the driver of USB, we can use USB
to program the programmable control panel.
4.2 Software Programming
You can use this software PS-WP to easily set every button of the programmable
control panel.
After connect the programmable control panel with PC by USB or RS232, we can
open the PS-WP to program the buttons for controlling.
The main window of PS-WP has five parts: main menu, panel (button) setting, event
setting, action list and event list. In this manual we will take programmable control
panels-V for example, to show the uses of all functions.
The main window of PS-WP is as below:

User Manual
PT-CON-WP8B
11
We will introduce all the configurations one by one.

User Manual
PT-CON-WP8B
12
4.2.1 Main Menu
The main menu includes file management, system model, connection type and help.
1) File management: Open/Save/Save as a configuration. After program, user can
save the configuration to a file, so that you can use the same configuration next
time.
2) System model: includes programmable control panels-H, programmable control
panels-V, WP19R etc, and the buttons interface view are different with different
models. The pictures below show the differences between programmable
control panels-V and programmable control panels-H.

User Manual
PT-CON-WP8B
13
Note: When select the model, it will pop up “Output Port Selection” dialog, user can
select different RS and IR types, depend on the uses of the two shared ports. The dialog
is as the picture below:

User Manual
PT-CON-WP8B
14
The output port set in PS-WP and the port used in the programmable control panel
is corresponding. And there are four output types. They are showed as below form
(“√” means port is available):
Output port
of the
Panel
Output mode
of PS-WP
IR1
RS232(1)
IR2
RS232(2)
IR3
RS232(3)
RS485
RS232(1)(2)
√
√
√
√
√
RS232(2),IR2
√
√
√
√
RS232(1),IR3
√
√
√
√
√
IR2,3
√
√
√
√
3) Connection type: the instructions are in the picture below:
The functions of the programmable control panel’s buttons will be available only
after the programmed data is uploading successfully.
4) Help: Show the information of PS-WP.
1) Com, connect by serial port.
2) USB, connect by mini USB.
3) Disconnect, disconnect the
connection.
4) Upload: upload the
programmed data to the
programmable control panel. It
will clear all the old data in the
programmable control panel.
5) Clear, clear the data in the
programmable control panel.

User Manual
PT-CON-WP8B
15
4.2.2 Panel/Key Setting
There are three different colors of keys in the panel set of PS-WP. Add a key action
to action list, then add events to this action, make this action will execute the events.
Here take programmable control panels-V for example, to introduce the uses of
different buttons: