PureTools PT-HDBT-1010 User manual

User Manual
PT-HDBT-1010
User Manual
HDBaseT 3.0 Extender set with USB and Audio breakout
Model PT-HDBT-1010
Designed in Germany
© 2022 PureLink GmbH All rights reserved. VersionV1.2

User Manual
PT-HDBT-1010
Preface
Read this user manual carefully before using this product. Pictures shown in this
manual are for reference only. Different model layouts and specifications are subject
to the physical product.
This manual is for operation instructions only, not for any maintenance usage.
In the constant effort to improve our product, we reserve the right to make changes in
functions or parameters without prior notice or obligation.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of this
publication may be copied or reproduced without the prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. It has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in
a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in
which case the user at their own expense will be required to take whatever measures
may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

User Manual
PT-HDBT-1010
REACH | 1907/2006/EU
ROHS | 2011/65/EU
PureLink hereby declares that this product PureTools PT-HDBT-1010 complies with
Directives 1907/2006/EU und 2011/65/EU.
EMC / LVD (Electro Magnetic Compatibility / Low Voltage Directive)
PureLink GmbH hereby declares that this product PureTools PT-HDBT-1010 complies
with Directives 2014/30/EU and 2014/35/EU. The full text of the EU Declaration of
Conformity is available at the following Internet address:
http://www.purelink.de/ce/4251364727249_CE.pdf

User Manual
PT-HDBT-1010
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before
using the device. Save this manual for further reference.
⚫Unpack the equipment carefully and save the original box and packing material
for possible future shipment
⚫Follow basic safety precautions to reduce the risk of fire, electrical shock and
injury to persons.
⚫Do not dismantle the housing or modify the module. It may result in electrical
shock or burn.
⚫Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
⚫Refer all servicing to qualified service personnel.
⚫To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
⚫Do not put any heavy items on the extension cable in case of extrusion.
⚫Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
⚫Install the device in a place with fine ventilation to avoid damage caused by
overheat.
⚫Keep the module away from liquids.
⚫Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module
immediately.
⚫Do not twist or pull by force ends of the optical cable. It can cause malfunction.
⚫Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.
⚫Unplug the power cord when left unused for a long period of time.
⚫Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

User Manual
PT-HDBT-1010
1
Product Introduction
Thanks for choosing Purelink PT-HDBT-1010, which consists of a transmitter and a
receiver. It can extend 4K or 1080p video to distance up to 328 feet (100 meters) over
a single CAT6A cable without compression. It supports audio de-embedding and ARC.
It also supports bi-directional IR, USB and RS232 pass-through control and Ethernet
extension. 24V PoC feature allows the transmitter and the receiver can be powered
from each other and only one power adapter is needed in system.
Feature
⚫18Gbps high bandwidth, HDMI V2.0.
⚫HDMI video resolution up to 4K@60Hz 4:4:4, HDR10, Dolby Vision.
⚫Supports HDCP bypass and HDCP 2.2 compliant.
⚫HDBaseT 3.0 solution which supports extending signal without compression.
⚫Extends 4K or 1080p video signals to distances up to 328 feet (100 meters) over a
single SFTP CAT6A cable.
⚫Bi-directional IR, USB and RS232 pass-through control and Ethernet extension.
⚫Supports bi-directional 24V PoC.
⚫Supports audio de-embedding and ARC (Audio Return Channel).
⚫Provides HDMI loop out on transmitter.
Package List
⚫1x PT-HDBT-1010-TX Transmitter
⚫1x PT-HDBT-1010-RX Receiver
⚫2x TX Mounting Ears with 2 Screws
⚫2x RX Mounting Ears with 2 Screws
⚫4x Plastic Cushion
⚫4x Plastic Cushion
⚫1x Power Adapter (24V DC 1.25A)
⚫1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

User Manual
PT-HDBT-1010
2
Panel Description
Transmitter Front Panel
No.
Name
Description
①
POWER LED
Illuminates green when power is applied, or blinks
when in firmware upgrade mode.
②
LINK LED
Illuminates when there is a valid HDBaseT link
between the transmitter and the receiver.
③
HDCP LED
Illuminates when the video contains HDCP content,
or blinks when the video has no HDCP content.
④
SOURCE LED
Illuminates when there is an HDMI source device is
connected to HDMI input port.
⑤
LOOPOUT LED
Illuminates when both HDMI source device and
HDMI display device (HDMI loop out port) are
connected.
⑥
USB
DIP switch for DEVICE or HOST mode selection.
DEVICE: The USB devices at transmitter
position are used to control the HOST PC at
receiver position.
HOST: The HOST PC at transmitter position is
controlled by the USB devices at receiver position.
⑦
DEVICE
Four type-A USB 2.0 ports for USB devices (e.g.
Mouse, Keyboard and Camera) connection to
control the PC which is connected to the HOST port
of receiver.
⑧
HOST
Type-B USB 2.0 port for PC connection. The PC can
be controlled by the USB devices which are
connected to type-A USB 2.0 ports of receiver.

User Manual
PT-HDBT-1010
3
Transmitter Rear Panel
No.
Name
Description
①
ETHERNET
Used for Ethernet extension together with the
ETHERNET port of receiver.
②
HDBT OUT
RJ45 port to connect the HDBT input port of receiver
by CAT6A Ethernet cable. The LINK LED illuminates
when there is a valid HDBaseT link between the
transmitter and the receiver. The HDCP LED
illuminates when the video contains HDCP content.
③
SOURCE
Connects to HDMI source device.
④
LOOPOUT
Connects to HDMI display device.
⑤
ARC OUT
Connects to audio player (e.g. amplifier) for ARC
audio output.
⑥
AUDIO OUT
Connects to audio player (e.g. amplifier) for audio
de-embedding from HDMI input.
⑦
IR IN
Connects to the IR receiver for IR pass-through.
⑧
IR OUT
Connects to the IR emitter for IR pass-through.
⑨
RS232
Connects to RS232 control device (e.g. PC) or a
third-party device for RS232 control.
⑩
FIRMWARE UPGRADE
BUTTON
Press the button with paper clip or other sharp tool
for 3s to enter firmware upgrade mode. Press the
button for 3s again can exit the mode.
⑪
DC 24V
DC connector for the power adapter connection.

User Manual
PT-HDBT-1010
4
Receiver Front Panel
No.
Name
Description
①
POWER LED
Illuminates green when power is applied, or blinks
when in firmware upgrade mode.
②
LINK LED
Illuminates when there is a valid HDBaseT link
between the transmitter and the receiver.
③
HDCP LED
Illuminates when the video contains HDCP content,
or blinks when the video has no HDCP content.
④
DISPLAY LED
Illuminates when there is a HDMI display device is
connected to HDMI output port and when input
source is detected.
⑤
ARC
DIP switch for ARC mode selection
HDMI: The ARC input via HDMI output port of
receiver.
PASS: Supports CEC & ARC pass-through.
SPDIF: The ARC input via SPDIF input port of
receiver.
⑥
USB
DIP switch for DEVICE or HOST mode selection.
DEVICE: The USB devices at receiver position
are used to control the HOST PC at transmitter
position.
HOST: The HOST PC at receiver position is
controlled by the USB devices at transmitter
position.
⑦
DEVICE
Four type-A USB 2.0 port for USB devices (e.g. Mouse,
Keyboard and Camera) connection to control the PC
which is connected to the HOST port of transmitter.
⑧
HOST
T Type-B USB 2.0 ports for PC connection. The PC can
HDCPLINK
DEVICE
USBDISPLAY ARC
SPDIF
HDMI
PASS
HOST
HOST
6
48 1 2 357

User Manual
PT-HDBT-1010
5
be controlled by the USB devices which are
connected to type-A USB 2.0 ports of transmitter.
Receiver Rear Panel
No.
Name
Description
①
ETHERNET
Used for Ethernet extension together with the
ETHERNET port of transmitter.
②
HDBT IN
RJ45 port to connect the HDBT output port of
transmitter by CAT6A Ethernet cable. The LINK LED
illuminates when there is a valid HDBaseT link
between the transmitter and the receiver. The HDCP
LED illuminates when the video contains HDCP
content.
③
DISPLAY
Connects to HDMI display device.
④
ARC IN
Connects to ARC audio source device (e.g.TV).
⑤
IR IN
Connects to the IR receiver for IR pass-through.
⑥
IR OUT
Connects to the IR emitter for IR pass-through.
⑦
RS232
Connects to RS232 control device (e.g. PC) or a
third-party device which is to be controlled.
⑧
FIRMWARE UPGRADE
BUTTON
Press the button with paper clip or other sharp tool
for 3s to enter firmware upgrade mode. Press the
button for 3s again can exit the mode.
⑨
DC 24V
DC connector for the power adapter connection.

User Manual
PT-HDBT-1010
6
Specification
Transmitter
Receiver
Video
Input
(1) SOURCE
(1) HDBT IN
Input Connector
(1) Type-A female HDMI
(1) RJ45
Input Resolution
Up to 4K@60Hz 4:4:4
Up to 4K@60Hz 4:4:4
Output
(1) HDBT OUT, (1) LOOP OUT
(1) DISPLAY
Output Connector
(1) RJ45, (1) Type-A female HDMI
(1) Type-A female HDMI
Output Resolution
Up to 4K@60Hz 4:4:4
Up to 4K@60Hz 4:4:4
Audio
Input
-
(1) ARC IN
Input Connector
-
(1) Toslink Connector
Output
(1) ARC OUT, (1) AUDIO OUT
-
Output Connector
(1) Toslink connector
(1) 3.5mm jack
-
Audio Format
Toslink (ARC): PCM, Dolby Digital, DTS 5.1CH
3.5mm Audio: PCM 2CH
Frequency Response
20Hz ~ 20KHz, ±3dB
Max Output Level
2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV)
nominal consumer line level signal
THD+N
< 0.05% (-80dB), 20Hz~20KHz bandwidth, 1kHz sine at 0dBFS level
(or max level)
SNR
> 85dB, 20Hz-20kHz bandwidth
Crosstalk Isolation
> 70dB, 10kHz sine at 0dBFS level (or max level before clipping)
L-R Level Deviation
< 0.3dB, 1kHz sine at 0dBFS level (or max level before clipping)
Frequency Response
Deviation
< ± 0.5dB, 20Hz –20kHz
Output Load Capability
1KΩ and higher (Supports 10x paralleled 10KΩ loads)
Stereo Channel
Separation
>70dB@1KHz
Control
Control Part
(4) DEVICE, (1) HOST, (1) USB
Switch, (1) IR IN,
(1) IR OUT, (1) RS232,
(4) DEVICE, (1) HOST, (1) ARC
Switch, (1) USB Switch, (1) IR IN,
(1) IR OUT, (1) RS232,

User Manual
PT-HDBT-1010
7
(1) ETHERNET
(1) ETHERNET
Control Connector
(4) Type-A USB 2.0,
(1) Type-B USB 2.0,
(1) 2-pin DIP Switch,
(2) 3.5mm Jacks,
(1) 3-pin Terminal Block,
(1) RJ45
(4) Type-A USB 2.0,
(1) Type-B USB 2.0,
(2) 3-pin DIP Switch,
(2) 3.5mm Jacks,
(1) 3-pin Terminal Block,
(1) RJ45
General
Bandwidth
18Gbps
HDMI Standard
2.0
HDCP Version
Input: HDCP 2.2, HDCP 1.4 compliant
Loopout: Follows the display’s HDCP version.
RX Output: Follows the source’s HDCP version.
CEC
Pass-through (when ARC switch is selected to PASS or SPDIF)
Bi-directional PoC
Supported
HDMI V2.0 Cable Length
4K@60Hz 4:4:4 ≤ 5m, 4K@60Hz 4:2:0 ≤ 15m, 1080P ≤ 20m
Transmission Standard
HDBaseT
Transmission Distance
4K/1080p ≤ 262 feet (80 meters)
Operation Temperature
-5 to +55℃(+23°to +131°F)
Storage Temperature
-25 to +70℃(-13°to +158°F)
Relative Humidity
10% to 90%, Non-condensing
Power Supply
Input:100V~240V AC; Output:24V DC 1.25A
Power Consumption
17W (Max)
Dimension (W*H*D)
200mm x 25mm x 100mm(Tx) 200mm x 25mm x 100mm(Rx)
Net Weight
Tx:540g Rx: 540g
Note:
1. Please use high-qualified HDMI cable fully compliant with HDMI V2.0 for reliable
transmission and connection.
2. Suggest to use 80m for installation maximum, if 100m requires high quality
SFTP CAT6A cable.

User Manual
PT-HDBT-1010
8
System Diagram
1) When ARC switch is selected to HDMI, and the TV supports ARC, the TV audio can
be transmitted back to the transmitter via HDMI output port of receiver, and then it
will be output by the ARC OUT & HDMI Source port of transmitter. CEC pass-through is
not supported in this mode.
2) When ARC switch is selected to SPDIF, the audio can be transmitted back to the
transmitter via ARC IN port of receiver, and then it will be output by the ARC OUT &
HDMI Source port of transmitter. Besides, it also supports CEC pass-through in this
mode.
3) When ARC switch is selected to PASS, the extender can pass the ARC signal and
support CEC pass-through. If the amplifier can work with the TV for ARC function, the
ARC audio can be transmitted back to the transmitter via HDMI output port of receiver,
and then it will be output by the ARC OUT & HDMI Source port of transmitter.

User Manual
PT-HDBT-1010
9
After-Sales Service
If there appear some problems when running the product, please check and deal with
the problems referring to this user manual. Any transport costs are borne by the users
during the warranty.
1) Product Limited Warranty: This product will be free from defects in materials and
workmanship for two years (The purchase invoice shall prevail).
Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the unit is within the Warranty period must be presented to obtain
warranty service.
2) What the warranty does not cover (servicing available for a fee):
⚫Warranty expiration.
⚫Factory applied serial number has been altered or removed from the product.
⚫Damage, deterioration or malfunction caused by:
⚫Normal wear and tear.
⚫Use of supplies or parts not meeting our specifications.
⚫No certificate or invoice as the proof of warranty.
⚫The product model showed on the warranty card does not match with the
model of the product for repairing or had been altered.
⚫Damage caused by force majeure.
⚫Servicing not authorized by distributor.
⚫Any other causes which does not relate to a product defect.
⚫Delivery, installation or labor charges for installation or setup of the product.
3) Technical Support: For any questions or problems, contact your distributor or
reseller and tell them the respective product name and version, the detailed
failure situation as well as the formation of the cases.

User Manual
PT-HDBT-1010
10

User Manual
PT-HDBT-1010
11
Asking for Assistance
Technical Support:
Phone: [phone] - 0
Fax: [phone]
Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday
Write to:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
[email protected]