Pyle PRMBN200 User manual

CURRENCY BINDING MACHINE
User Manual
PRMBN200
3
Debug Method: Press the "Clear" button waiting for temperature to 00
1. Temperature = 00 is tightness adjustment: (Factory value=30)
Press "Enter paper" button then into the set state, now press "+, -" button, enter the
required values, press "Enter paper" button again, Setting out the state ,press "Quit
paper" button, Set item switch.
2. Temperature = 01 is feed length adjustment: (Factory value=3) press "+, -" button,
input the required values, press" quit paper" button, set the project into the next
3. Temperature = 02 is Sensitivity adjustment: (Factory value=9)
Press "Enter paper" button then into the set state ,now press "+, -" button, enter the
required values, press "Enter paper" button again, Setting out the state, press "Quit
paper" button, Set item switch
4. Temperature = 03 is Temperature sensor compensation value: (Factory value=O)
Press "Enter paper" button then into the set state ,now press "+, -" button, enter the
required values, press "Enter paper" button again, Setting out the state, press "Quit
paper" button, Set item switch
5. Temperature = 04 is Sensor detection threshold value paperless:
(Factory value = 30) Press "Enter paper" button then into the set state, now press "+,
-" button,enter the required values, press " Enter paper" button again, Setting out
the state, press "Quit paper" button, Set item switch
6. Temperature = 05 is Set o time: (Factory value=60) press "Enter paper"
button then into the set state ,now press "+, -" button, enter the required values,
press "Enter paper" button again, Setting out the state, press "Quit paper" button,
Set item switch
7. temperature =06 is Operation mode setting: (Factory value=O)
Press "Enter paper" button then into the set state ,now press "+, -" button, enter the
required values, press "Enter paper" button again, Setting out the state, press "Quit
paper" button, Set item switch
SETUP AND RESIZE
QUICK OPERATION (Continued)
ON/OFF:
This machine has automatic and manual shutdown functions.
Automatic shutdown: This machine has an automatic shutdown function, if the
stop operation time interval of more than set o, the system will automatically cut
o power supply.
Manual Shutdown: Users can use the power switch to turn on or o.

12
DIAGRAM PRODUCT SPECIFICATIONS
QUICK OPERATION
DISPLAY
PRODUCT FEATURES
Instant heat: No warm-up needed; once opened, you can immediately start using.
Easy to operate: Simply place the notes vertically into the entrance, then the
operation will automatically start and complete.
Function: Chinese or English display for global accessibility, see failures at a glance,
users can exclude their operation, reduce the probability of repair, improve user
productivity.
Easy setup: Demand on the heating temperature can be set.
Safe and convenient: Automatic timing function, Note in the stop bar after 2 hour
automatic shutdown, if an error is encountered, automatic fault shutdown initiates.
General Supplies: Users can adjust by setting the temperature of hot pressing to
meet the dierent needs of various paper tapes.
Bundle note range: RMB notes and national bank notes can be applied
Binding speed: ≤ 1. 5 seconds /once
Power: AC 1 OOV-240V /47-63Hz
Standby power: ≤10W, Max power: ≤ 60W
Noise: : ≤ 70DB
Weight: 6kg
Paper width: 20mm
Dimensions: 240*200*220mm
Install paper note: With the top of the machine open, set binding tape as shown in
column 3 of the lateral direction, leads to take the lead, this time pay attention to the
direction with the installation disk to aligh with case cited above diagram.
Power: Access to power, and press the Power switch to“ON”position, the machine
will automatically enter the working state.
Covertape: Will take the lead through the guide wheel A, without paper detection
sensor, by passing the lateral guide rollers B, C and loaded by the guide rollers into
the band mouth, pressing the enter key then automatically completes the actions.
Bind: The notes will be counted into a working position, then closely aligns with
the left side of the pressure plate notes, notes contact with the front bae with the
limit, photoelectric switch sensor to the notes already in place, the control system
automatically starts binding action.
Complete: When the band heard the collection, Adjacency voice prompt action to
complete, remove the tie a good note, the end of a bundle.
Glue should face up