Pyle PST30 User manual

www.pyleaudio.com
www.pyleaudio.com
www.pyleaudio.com
www.pyleaudio.com
STROBOSCOPE
STROBOSCOPE
STROBOSCOPE
STROBOSCOPE
TACHOMETER
TACHOMETER
TACHOMETER
TACHOMETER
MODEL:
MODEL:
MODEL:
MODEL: PST30
PST30
PST30
PST30
OPERATION
OPERATION
OPERATION
OPERATION
MANUAL
MANUAL
MANUAL
MANUAL
CAUTION
CAUTION
CAUTION
CAUTION
● Do not look directly at strobe or shine at others. Light
pulses at a frequency greater than 5 Hz may cause
photosensitive epilepsy in some individuals if directly
viewed.
● To Avoid Injury, do not point the light beam of the
instrument or have it reflected into the eyes of people
or animals.
● A feature of the instrument is to make moving objects
appear to be stationary. Precaution should therefore
be taken to ensure that there is no physical contact
made with objects being viewed.
● Do not leave the device close to water or any other
liquid to avoid damage.
● If not using this instrument for extended periods of
time, remove the batteries to prevent potential battery
leakage which may damage the product.
● This instrument contains no user serviceable parts
and should not be opened by the user.
● Repair or service should be done by a qualified
technician only.
● Only use a dry cloth to clean the plastic case.
FEATURES
FEATURES
FEATURES
FEATURES
The Digital Stroboscope has a microprocessor circuit
design, high accuracy, digital readout, that is ideal for
inspecting and measuring the speed of moving gears,
fans, centrifuges, pumps, motors and other equipment
used in general industrial maintenance, production,
quality control, laboratories, and as well as for schools
and colleges for demonstrating strobe action.
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
Measuring range: 60~19999 RPM (round per minute) /
FPM (flashes per minute.)
Accuracy: 0.05%
Resolution: Less than 1000RPM: 0.1RPM/FPM
More than 1000RPM: 1RPM/FPM
Display: 19999
Power: 4 × 1.5V R6P .AA.UM-3 battery
Battery consumption: Approx.60mA
Dimension: 8.03 ” (204mm) × 2.87 ” (73mm) × 1.38 ” (35mm)
Weight: Approx. 200g
PANEL
PANEL
PANEL
PANEL DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
A: The object
B: Light beam
C: Lens
D: Flash Switch
E: LCD display
F: Flash Rate Value Increase Button
G: Flash Rate Value Decrease Button
H: Coarse/ Fine Tuning Button
I: Power button
J: Battery cover
K Backlight switch

DISPLAY
DISPLAY
DISPLAY
DISPLAY DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
1. To alter between Coarse and Fine tuning, select the
Coarse / Fine Tuning button to change from Coarse to
Fine adjustment.
Press again to switch back to Coarse. When in Fine
adjustment mode, “ FINE ” icon will appear on the
display.
2. Tach unit symbol, indicator rotation per minute.
3. Indicator symbol, represent in measuring.
4. Measuring data.
5. Low battery indicator symbol.
OPERATION
OPERATION
OPERATION
OPERATION INSTRUCTION
INSTRUCTION
INSTRUCTION
INSTRUCTION
Power ON/OFF: Open the battery compartment cover
on the back of the unit and place the batteries in the
battery holder properly. Then press and hold the Power
Switch. The display will turn on and show the initial
factory default flash rate of 1200 RPM. Coarse tuning
is the default.
Manual
Manual
Manual
Manual Adjust
Adjust
Adjust
Adjust TACH
TACH
TACH
TACH
In COARSE adjust mode, press “ up ” or “ down ” button,
the value of flash will increase or decrease when the
range is greater than 1000 RPM or 10 RPM when less
than 1000 RPM correspondingly. In FINE adjust mode,
press “ UP ” or Down ” button, the PHOTO TACH will
increase or decrease 1 RPM when greater than 1000
RPM, or 0.1RPM when less than 1000 RPM
correspondingly.
Auto
Auto
Auto
Auto Adjust
Adjust
Adjust
Adjust TACH
TACH
TACH
TACH
Press “ UP ” or “ Down ” button for more than two
seconds to enter the Auto-adjust Mode. In COARSE
adjust mode, the value will increase or decrease when
the range is greater than 1000 RPM or 10 RPM when
less than 1000 RPM every 0.2 seconds. In FINE adjust
mode, the value will increase or decrease 1RPM
(>1000 RPM) or 0.1 RPM (<1000RPM) every 0.2
seconds
Note: Once the maximum of 19999 or minimum of 60
RPM is met while adjusting the rate, the device will
automatically stop at those thresholds.
TACH
TACH
TACH
TACH measuring
measuring
measuring
measuring
The Stroboscope will also stop motion at 2:1, 3:1, 4:1,
5:1, etc. This is normally referred to as harmonics. To
ensure unison, turn the dial until two images appear –
this will double the actual speed. Then lower the
flashing rate until a single and stationary image
appears - this is the actual true speed.
Checking
Checking
Checking
Checking motion
motion
motion
motion
For motion analysis, simply locate the actual speed as
mentioned above and then turn the dial slowly up or
down. This will give a slow motion effect allowing
complete inspection.
The
The
The
The manual
manual
manual
manual contents
contents
contents
contents are
are
are
are subject
subject
subject
subject to
to
to
to change
change
change
change without
without
without
without notice.
notice.
notice.
notice.
The
The
The
The Company
Company
Company
Company do
do
do
do es
es
es
es not
not
not
not take
take
take
take any
any
any
any responsibility
responsibility
responsibility
responsibility for
for
for
for
accident
accident
accident
accident s
s
s
s that
that
that
that result
result
result
result out
out
out
out of
of
of
of error
error
error
error during
during
during
during operation
operation
operation
operation of
of
of
of our
our
our
our
unit.
unit.
unit.
unit.