Pyle PDWMG46 User manual

PDWMG46
UHF
www.pyleaudio.com

CATALOG
FOREWORD
SYSTEM FEATURES
RECEIVER FEATURES
TRANSMITTER FEATURES
SYSTEM CONNECTON
SPECIFCIATION
............................................................................................2
................................................................................2
.............................................................................3
.......................................................................4
.............................................................................4
.......................................................................................5
Receiver
Transmitter
Audio cable
AC power adapter of special receiver
Battery 1.5V AA
Battery 1.5V AAA
User manual
....................................................................................................1
................................................................................................1
...............................................................................................1
.......................................................1
.........................................................................................2
......................................................................................1
..............................................................................................1
SYSTEM COMPOSITION
1 SYSTEM FEATURES
Flex jack swiveljack plug matchingevery guitar output.
Extended frequency responseoptimized for guitar and bass
No cable orseparate body packto hassle with
Input gain controlfor compatibility withall instrument pickups
Wide frequency response and dynamic range for true hard-wired sound.
The guitar bugsystem is probably the easiestway to turn a guitar, bass
or probable keyboardinto a wireless instrument.
The flex jack swivel jack plug will mate with any type of output jack and
is spring loadedto hold thesecurely against theinstrument.
In addition, the is so small it is almost invisible and won't be in
your way while playing .Since it sits right on top of the
Instrument' s output jack, the noiseless on/mute-off switch and gain
control are always within easy reach.
Receiver is designedfor use with compact effects pedals.
It features a 1/4 " output jack, peak LED and a volume control.
You can use two pieces of 1.5 volt batteries or AC adapter
AC adapter to power the receiver.
21
Thank you forpurchasing our product, please read this instruction manual
carefully so thatyou will understandhow to operatethe unit thatyou
purchased correctly. Please keepand store thisinstruction booklet ina safe
place after readingit for futurereference. This series of professional
microphone system usesa super steadyPLL-synthesized control circuit
that matches ahigh efficient, low consumption discharging technique. We
also apply an independently developed mobilefrequency compression
and expanding circuitthat is chainlinked with imagefrequency filters and
three time checkednoise filters inthe receiving unit.Every unit mustpass
strict tests andquality control bythe manufacturer.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Power button: Turns ON/OFF the receiver
Squelch control button.
Volume Control:Rotate the knobto increase ordecrease the volume
of the receiveroutput.
Antenna "A":Supply the RF for receiver
Antenna indicator "A".
Antenna"B":Supply the RF for receiver
Antenna indicator "B"
Audio indicator: The green light of the AF signal indicator glows
according to the volume of the microphone when talk or sing to
transmitter
Low battery indicator: This light glows when there is less of useful
operating time, allowingbattery to bechanged before poweris depleted.
(Use 1.5VAA BATTERY)
Power on indicator: This light glows when the receiver is plugged into an
electrical outlet and switch is pushed, it indicates that the receiver is on.
2 RECEIVER FEATURES
1.
2.
3.
4.
5.
6.Battery cover:Open the cover and set 1 XAAA(1.5V)Alkaline battery.
Power and audiomute switch: pushthe switch to"ON" position, the
indicator shines fora moment. Pushedthe switch tothe middle of
"ON""OFF" position, allows muting themicrophone audio, avoiding
the "thump "noise that can occur when turning the microphone audio.
it is recessedto prevent itfrom being accidentallyturned off.
Gain control switch:Adjust audiolevel, for fittingall kinds ofsignal input,
it is onthe "L "position in the factory.
Antenna:Supply the RFfor transmitter
.6.35mm audio plug.
Low battery indicator: This light glows when there is less of useful
operating time, allowingbattery to bechanged before poweris depleted.
(Use 1.5VAAA battery)
11.
12.
13.
Battery cover: Open the coverand set 2X1.5VAA)Alkaline batteries.
1/4" phone jackaudio output connector(Unbalanced high Z):An
unbalanced audio cable with 1/4" phone plug(such as standard guitar
cable)can be used between this connector to your amplifier input
Power input connector: Connect the AC adapter to this jack and then
plug into anAC electricaloutlet.(Please use suppliedAC adapter)
3 TRANSMITTER FEATURES
3 4

NOTE: For a list of compatible frequencies that are usable in your area,
refer to thesupplied frequency supplement.
4 SYSTEM CONNECTION
1.
2.
3.
4.
5.
6.
Connect the supplied AC power adapter into the DC INPUT connector
in the back of the receiver, plug the adapter into a wall socket
Connect the receiver's audio output to the mixer's input by 6.35mm
audio cable
Pushed the receiver's power switch to "ON" position, the power
indicator will glows.
Slide the transmitter's power switch to "ON" position, the indicator
shines for a moment, at that time, the receiver's signal light will glow.
Adjust receiver volume knob, and the volume adjustment of mixer or
amplifier to get a suitable volume.
When the performance is over, turn off the sound system and slide the
transmitter 's POWER/OFF switch to the "OFF" position to conserve
battery power.
5 SPECIFICATIONS
1.RF Carrier Frequency Range
640MHz to 698MHz (Available frequencies depend on the applicable
regulations in the country where the system is used).
2.Effectiver Range
50m(150ft)Under optimal conditions
NOTE:Actual working range depends on RFsignal absorption,
reflection, and interferencefrom objects andenvironment.
3.Audio Frequency Response
Typioally 50Hz to 15,000Hz, 3dB
NOTE:System response is depend on the using accessory of
microphone
4.Modulation:FM
5.Audio bandwidth:40Hz to 20kHz
6.THD:typ.1%
7.S/N ratio:typ. 103dB(A)
8.Power requirements:9V DC 150mA
9.Transmitter current:80mA
10.Receiver power supply:2X 1.5V AA size battery
11.Transmitter power supply: 1 X 1.5V AAAsize battery
12.Dimensions : Receiver: 5.1" X 3.1" X 1.4" inches
Transmitter: 3" X 1" inches
65