Pyle PLTTB9U User manual

USB/SD BELT DRIVE TURNTABLE PLAYER
PLTTB9U
READ THIS INSTRUCTIONS CAREFULLY BEFORE USE
AND STORE IN A SAFE PLACE FOR FUTURE REFERENCE

BEFORE USE
Read this before operation
• Choose the installation location of your unit carefully. Avoid placing it in direct sunlight or close to a
source
of heat. Also avoid locations subject to vibrations and excessive dust, heat, cold or moisture.
• The ventilation holes should not be covered. Make sure there is enough space above and beside the
amplifier/receiver (about 4 hours). Do not place a CD player or other equipment on top
of the Turntable
PlayerlRecorder/
• Do not open the cabinet as this might result in damage to the circuitry or electrical shock. If a foreign
object gets into the set. Contact you dealer.
• When removing the power plug, never yank the cord.
• Do not attempt to clean the unit with the chemical solvents as this might damage the finish. Use a clean,
dry cloth.
• Keep this manual in a safe place for future reference.
CAUTION
CAUTION AEDlJCETHE ELECTRIC SHOCK
00
REMOVE CO\lFR
NO USERst:RVlCEABLE P.ARTS INSIDE. REFER SERVICING
PERSONNa
A
Ii.
ATTENTION
TI"ie~ ffi!!IflI.J8I ~ irr:IportarIt opemIi"Ig aM mameOOfiCe ~ foryour safety,
it~~to"'l:olhe~
WARNNG: TO PRE\IENT RAE OR $rOOK HAZARD, 00 NOT EXPOSE THIS APPUANCEID
DRIPPING OR SPLASHIf\U
Note:
111is unit will ~ warnl when ~ tor along period of tJme. Th~ ~ ~ anddoesnot indicate a
problemwith !he unt .
Automatic Stereo Turntable System
Installation and Operation
CAUTION: To avoid stylus damage, make certain the included stylus guard is in place whenever
the turntable is being installed, moved or cleaned.
The turntable features:
1. 3-speed turntable fit for 33 113,45,78 RPM
2. belt-drive and semi-automatic playtone arm
4. ceramic stereo cartridge with
jewel stylus
5. built-in
45 rpm adapter
6. slot-in USB/SD/MMC for encoding & decoding
7. analog AM/FM/FM stereo radio
7. Aux in and headphone sockets
8. full range stereo speakers
9. removable semi transparent plastic dust cover
L Transparent dust cover
2. 45rpm adapter
3. Tone arm set
4. Full range dynamic
stereo speakers
5. Play/pause lift lever
6. Auto/manual stop switch
7. Speed switch
8. PowerNolume knob
9. Tuner knob
10. USB socket
11. USBfMMC socket
12. Function switch
13. Tuner BA~D switch
14. Headphone
jack
15. Aux in jack
16. REC key
17. SOURCE
18.
19.
key
23. :\EXT key
24. Diamond cartridge
25. The big
platter
CAUTION:
LOCATION OF CONTROLS
Usage of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
This unit should not
be adjusted or repaired by anyone except qualified service personnel.

CONNECTION
1. Connect the powercord to AC outlet
2. Switch the function selector to PHONO orUSB/SD or TUNER function. Now your system is
ready to play the music.
FM/AM OPERATION
1. Set FUNCTION switch to TUNER mode, then choose needed band (AM, FM and FM stereo)
by BAND switch.
2. Search stations: Rotate the TUNER knob to choose request station, or press PREY/NEXT
keys to choose idea stations. User can also press one
of the two keys a litte longer around 1.5s
then the model will search automatically and it would stop at a clearest station.
PHONO OPERATION
I. Press the Function switch to PHONO position. Then put a record
on the Platter lightly.
In certain circumstances, 45 RPM adapter is
needed;
2. Select the speed of record: 33 113, 45, 78rpm according to vinyl
to played.
3. Remove the stylus guard and push the lift lever upward to raise
the tone arm from the arm park, and then move the cartridge holder over the record gently,
now the platter will run automatieally (default set
of AutolManual stop switch at ON
position). Then put down the lever, the tone arm would drop and touch record surface gently.
Now users can enjoy their favorite sons.
4. Select the auto/manual stop control: The turntable will stop automatically while the song on
the record finished when the switch at ON position. The other side it will always play when it
is at OFF position, this may helps to play some long recorded vinyl which can not
be played
to the end by normal
way.
5. Rotate the volume control knob to get desired sound leveL
6. Push the arm lift lever up to raise the arm, now platter will still running but play will pause.
To continue the play, userjust need to put down the lever.
7. Record vinyl: Firstly insert memory device (USB drive mp3 player or SD IMMC card). When
turntable
is working, press the REC key on front control board of the unit, then press
SOURCE key to choose USB or CARD mode, later press REC key again now recording
works will begin.
To finish the work just need to press the STOP key.
Note: Recordedfile in mp3format with 128bit.
USB/SO RECORDING AND PLAYING
PLAYING THE MUSIC FROM USB/SDIMMC DIRECTLY:
1. Be sure power is on, insert USB drive or Mp3 player into USB port andlor insert MEMORY
CARD (SDIMMC) into SD socket.
2. Set FUNCTION switch to USB/SD position, press SOURCE key to chopse music source
USB orSD.
3. The device supports for Mp3 and WMA formats. During play status, press PLAYIPAUSE
button once to halt playing, press it again to continue. ,.
4. Press PREY once to play the preview song, hold down continuously to speed up selecting
backward. Press NEXT once to play next one, holds down continuously
to speed up selecting
forward.
5. Press FOLDER+ key, the unit will search music files from first folder to the last one on
mcmory devices, then press continually to recycle overview all folders.
6. Press STOP to end up the play.
RECORD OPERATION:
1. Select Audio source: PHONOE or External audio source through AUX IN jack and play it on.
2. Insert USB drive and/or memory card.
. 1. Now press REC key and press SOURCE to choose memory type USB or SD. Then press REC
once again, it will start working IlDW.
4. Press STOP key to end up the work..
Note: The device also support
for transit music files between SD and USB. Steps are similar to
above operation.
The device supportsfor
Mp3 and WMAformats playback.
PHONES OUTPUT/EARPHONE JACK
1. The turntable can be connected to amplifier or speakers by 3.5mm
HEADPHONE jack.
2. Private listen
of earphone also can be realized through this jack.
AUX IN
JACK
1. The external sound sourcing can be played and recorded through the device.
2. The external sound sourcing can be recorded to the U stick or SD througb the
sockets
..
REPLACING STYLUS

1.
TIPS FOR BETTER PERFORMANCE
1. When opening or closing the turntable cover, handle it gently, moving it either at the center or
equally from both sides.
2. Do not touch the stylus tip with your fingers; avoid bumping the stylus on the turntable mat or a
record's edge
3. Clean the stylus tip frequently, using a soft brush with a back-to-front motion only.
4. If you use a stylus cleaning fluid, use it very sparingly.
5. Wipe the dust cover and turntable housing gently with a soft cloth. Use only a small amount of
mild detergent solution to clean the turntable and dust cover.
6. Never apply harsh chemicals or solvents to any part of the turntable system.
7. Prior to moving the turntable, always unplug it from the AC outlet and fasten the tone arm on
the tone arm rest with the vinyl twist-tie.
o MAINTENANCE AND CARE
Caring for the player
• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
• The maximum ambient temperature: 35 "C
• Electronic products of this kind shoblld never be subjected to extreme temperatures or high humidity.
For instance, this set should not
be placed in bathing areas of around stoves and radiators.
• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before
operating it any further.
Cleaning the Unit
•
To prevent fire or shock hazard, disconnect your unit from the AC power source whcn cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution
when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
Inclination
• Do not install the unit in a inclined position, It is designed to be operated in a horizontal position only.
Condensation
• If the unit is brought directly from a cold to a warm location, moisture may condense inside the player,
and cause damage
it. When you first install the unit, or when you move it from a cold to a warm
location, wait for 30 minutes before operating the unit.
•
Disconnect Power
•
If you are not going to use the player for long time, be sure do discounect the player from the AC
power source.