Qanon D Series User manual

Thank you for purchasing our products.
Please read the owner’ s manual thoroughly prior to using the system.
Please keep the manual for future reference.
D SERIES DIGITAL PROCESSOR
USER'S MANUAL
Versions: 2.0

Digital Matrix Processor
INDEX
FUNCTIONS---------------------------------------------------------------------------------------------- 1
FRONT PANEL-------------------------------------------------------------------------------------------1
REAR PANEL--------------------------------------------------------------------------------------------- 2
OPERATION GUIDANCE-----------------------------------------------------------------------------2-4
PC SOFTWARE CONNECTION------------------------------------------------------------------- 5-6
PC SOFTWARE SPECIFICATIONS--------------------------------------------------------------7-12
SPECIFICATIONS-------------------------------------------------------------------------------------- 13
ACCESSORIES------------------------------------------------------------------------------------------13
REAR PANEL CONTROL PORT-------------------------------------------------------------------14-15
EXTEND REMOTE CONTROL PROTOCOL---------------------------------------------------16-18
SAFETY INSTRUCTIONS----------------------------------------------------------------------------19-20

Digital Matrix Processor
1
1
4
7
9
FUNCTIONS
● 96kHz sampling rate, 40-bit DSP processor, 24-bit AD/DA convertor.
● Input processing includes Gain, Mute, Link, High-cut, Low -cut, Noise gate, 8PEQ, 31 segment graphic
equalizer, Phase, Delay.
● Output processing includes Crossover, 5PEQ, Gain, Mute, Compressor/Limiter, Phase, Delay, Link.
● Every input and output can do matrix assign freely.
● Adjustable PEQ frequency, Gain and Bandwidth, the gain step is 0.1dB, we can choose style: Peak,
H-shelf, L-shelf, LP-6dB, LP-12dB, HP-6dB, HP-12dB, ALLPASS1, ALLPASS2.
● The style of all High-cut, Low-cut filter and Distributor Unit: Butterworth, Linkwitz- Riley, Bessel,
Slope is-6dB/oct ~-48dB/oct.
● Adjustable compressor/limiter threshold, soft knee, ratio, attached time and release time. Noise gate's
threshold, hold time, attached time and release time can be adjustment.
● The parameters of input and output adjusting are linkable, revisable input and output channels.
● All delay module's delay time can reach over 680ms the step is: 0.021ms.
● Parameter setting of each channel can copy freely, build-in signal generator.
● Input and Output on the front panel are equipped with 5-segment high precision level indicators, key
indicators, security protection function.
● 20 user preset, 1factory preset, device parameter and single preset file can save in computer; it also
can download from computer and save in the device. The device itself can store multiple preset
parameters and recall freely. With PC software, one-key online made the operation more convenient.
● USB and RS232 controlling ports, Online remote control and 255 units linkable through Rs485, and
also can realize wired and wireless connection controlled in long distant through port.
FRONT PANEL
2
3
5
6
8
10
1, Input Level Indicators
5-segment high precision LED show the situation of current input channel's level.
2, Input Edit Keys
Press to enter into relevant channel, parameters will show on the edit key and LCD.
3, Input Mute Keys
Mute channel by pressing and exit by pressing again.
4, Output Level Indicators
4-segment high precision LED and1 compressor signal LED shows the status of output level and
compressor on current channel.
5, Output Mute Keys
Mute channel by pressing and exit by pressing again.
6, Output Edit Keys
Press to enter into relevant channel edit status parameter will show on the edit, Key and LCD.

Digital Matrix Processor
2
4
7, LCD
Show all the related operation parameter and status of current operation.
8, Parameter Edit Knob
Edit the whole menu and parameter setting confirm by press.
9, Parameter edit keys
Choose all the system menu/input parameter/output parameter, exit by pressing ”exit” key.
10, USB
Used to connect with PC and center-control equipment, remote control.
REAR PANEL
1
2
3
5
6
1, Power Socket
The voltage is 95V-250V.
2, Power on/off Switch 3,
RS232/485 interface
Center-control by RS232, cascade control by RS485.
4, Ethernet control interface, achieve long-distance control by wire or WIFI 5,
Output interface
Male XLR balanced output 1-8.
6, Signal input interface
Female XLR balanced input A-D.
OPERATION GUIDANCE
Below status after power on:
4*8II DSP Processor
Version 1.0
Power on, show brand, model and version.
DSP Processor
F
00
Default Preset
After self-check, show brand, model and current user preset.
Press UTIL key, enter below setting status
ID Number Select ID:
1
Press the first time, enter ID number setting: the ID number of the units,
should be different when cas cade connection, the setting scale is1-254. (If cas
cade connection units are over 16 or long distance, a loaded 120 ohms
resistance should be parallel connected by RS 485.

Digital Matrix Processor
3
Manual IP Setting
192.168.1.101
Press the second time, enter IP address setting: factory default is
192.168.1.101 , users can set different IP address for each device for
different applications.
Unit Lock
Password 1234
Press the third time, enter password setting: users can choose all the words or
numbers to set the password they want, the initial password is 1234.
Input Source Select
Analog Input
Press the fourth time, enter signal source selection: pink noise, white noise and
sine wave 20Hz-20kHz.
Copy channel select
InA - InB
Press the fifth time, enter copy channel selection: input or output channel can
copy freely.
Delay Units Select
ms
Press the sixth time, enter delay unit setting: ms, m, ft can be chosen.
Press RECALL/SAVE key, enter below setting status
Load preset
F00 Default Preset
Press RECALL key, enter preset transfer. Users can transfer the saved
Settings U01-U20 and the initial setting F00.
Store preset
UO1 Default Preset
Press SAVE key, enter preset save. Users can save the adjust status in
U01-U20.
Press INPUT EDIT enter the settings as follows
I
NA
GAIN -60. 0dB
Default preferred option is gain the scale is -60dB-+12dB.
PEQ:1 F: 50.7 Q:3.00
G: 0.0dB PEAK ON
Press PEQ/GEQ enter PEQ parameter setting PEQ current filter number is 8, the
scale of “F” is 20Hz-20kHz, “Q” is 0.4-128, "G" is -12dB- +12dB, the style of filter
are Peak, Low-shelf, High-shelf, Low-cut, High-cut, Allpass1,
Allpass2, Bypass(ON/OFF).
GEQ:1 Freq: 20.0Hz
GAIN: 50.0dB
Press the second time“PEQ/GEQ” key, enter Graphic Equalizer parameter
setting interface: 31 GEQ in each input channel. Freq adjustment scale is
20Hz-20kHz, GAIN adjustment scale is -12dB---+12dB.
INLINK
A: √ B: X C: X ID: X
Press “LINK”, enter linking adjustment selection: If the current
channel is INA, you can choose INB, INC, IND channel to adjust
parameter simultaneously,together.
I N A
DELAY 0.000ms
Press “DELAY”, enter delay parameter setting: the scale is 0-680mS, 0-
234m, 0-766ft.
HP: 19.6 BYPASS
LP: 20K15 BYPASS
Press “X-OVER” enter low-high pass parameter setting,the scale of the
“HP” is 20Hz -20kHz,“LP” is 20Hz -20kHz,3 different slanting rate for
low/ high pass filter Butterworth,Bessel,Linkwitz-Riley,Slanting rate is
-6dB--48dB.
GATE T: -90.0 HT: 100
AT: 1ms RT: 100ms
Press “COMP/GATE” key, enter Input channel noise gate parameter interface:
noise gate threshold “T” scale is -90-0dB, hold time “HT” adjustment scale is
10-999ms, attached time “AT” scale is 1-999ms, release time “RT” scale is 10-
3000ms.
INA
PHASE 0
Press “PHASE”, enter phasic adjust setting, adjustment scale is (0/180).

Digital Matrix Processor
4
,
Press OUTPUT EDIT enter the settings as follow
OUT1
GAIN +0.0dB
Default preferred option is gain,the scale is- 60dB--12dB.
PEQ: 1 F: 4 0.2 Q: 3.00
G: 0.0dB PEAK ON
Press ”PEQ”, enter PEQ PARAMETER SETTING: ”PEQ” current number is 9,
the scale of “F” is 20Hz-20kHz, “Q” is 0.4-128 “G” is -12dB- +12dB, the style
of filter are Peak,Low-shelf, High-shelf, High-cut, Low-cut, Allpass1,
Allpass2, Bypass(ON/OFF).
OUTLINK 1:
√
2:X 3:X
4:X 5:X 6:X 7:X 8:X
Press “LINK”, enter linking adjustment selection: if the current channel is “OUT1”,
you can choose OUT2, OUT3, OUT4, OUT5, OUT6, OUT7, OUT8
channel to adjust parameter simultaneously.
OUT1
DEALY 0.000ms
Press “DELAY” enter delay parameter setting: the scale is 0-680mS, 0-234m 0-
766ft .
HP: 19.6 BYPASS
LP: 20K15 BYPASS
Press “X-OVER” enter low-high pass parameter setting: the scale of “HP” is
20Hz-20kHz, “LP” is 20Hz- 20kHz, 3 different slanting rate for low/high pass
filter:Butterworth, Bessel, Linkwitz-Riley, Slanting rate is -6dB--48dB.
OUT1 MATRIX SELECT
A:
√
B: X C: X D: X
Press “MATRIX” enter matrix setting, all the output channel can choose one or
several input signal freely.
OUT1 A: +0.0 B: +0.0
MIX C: +0.0 D: +0.0
Press the second time “MATRIX” key, enter matrix route output gain
interface: factory default is 0dB, adjustment scale is -60dB-0dB.
COMP TH: +20.0 R: 1.0
K: 0dB A: 50 RT: 1500
Press “COMP/GATE” enter compressor setting: the scale of threshold is -60dB~
+12dB, startup time is 1-999ms,attached time is 10-3000ms, ratio is 1:1, 1:10-LIMIT.
LIMIT TH: +20.0dB
AT: 50ms RT: 500ms
Press the second time “COMP/GATE” key enter peak limiter parameter
interface: threshold “T” adjustment scale is -90dB-+20dB, attached time “AT”
adjustment scale is 1-999ms, release time “RT” adjustment scale is
10-3000ms.
OUT1
PHASE 0
Press “PHASE” enter phase parameter setting: the scale is 0/180.

Digital Matrix Processor
5
PC SOFTWARE
Notice: User manual, PC software are on the attached CD, due to the software upgrades time by time, Please
do control your DSP processor ONLY by this CD!
USB connection steps
PC or laptop
DSP Processor
USB connection
1, Click the PC software on the CD, press next step to continue according to the instruction until Finish setup,
then exit.
USB cord

Digital Matrix Processor
6
2, Connect the processor to the computer by USB, after turning on the device, the computer will
Searching new hardware automatically, during setup new hardware there will show the.
Warnings: hardware setup success and can be used.
3, Open PC controlling software, PC software will find USB and connect device, after that the on-Line key
change into green at the top right corner and show “Online” , you can operate the Processor by controlling
software, Click “Online” button before exit.

Digital Matrix Processor
7
PC SOFTWARE SPECIFICATIONS
THE FIRST: VOLUME CONTROL INTERFACE
1, Menu
File
Open and save preset parameter, the whole date upload to the computer and
download to the device.
Link
Input and output channels can be set freely to adjust all of the parameters.
Copy
Parameter copy freely between the input and Output channels.
Lock
Setting password of the panel to ensure the safety of the device.
Setting ID/IP
To cascade control more than 254 device by setting different ID, Setting ID/IP
address for Long- distance and wireless WIFI control.
Test Tone
Buid-in signal generator, outputting pink noise, white noise and sine wave.
Channel Name
The whole channel name are revisable.
Language
Chinese and English menu is switchable.
Help
RS232 control protocol codes for reference.
2, Spectrum Area:
You can choose PEQ and phase freely which show the input andoutput channels.
3, The Volume Control Area:
Gain, Phase, Mute control for all input & output channels.
4, Preset Operation Area:
Save or convert preset parameter and show current preset parameter status.
1
2
3
4

Digital Matrix Processor
8
THE SECOND:NOISE GATE INTERFACE
1,display the current noise gate status curve and input channels level indicators.
2, all input channels noise gate parameters can be set. Noise gate threshold(-60~0dB), attach
time(1~999ms), hold time(10~999ms), release time(10~3000ms) can be adjustable continuously for
input.
THE THIRD:COMPRESSOR INTERFACE
1, Show compression status, level indicators and impression status of all channels.
2, Set the whole compression parameters for output channel, the compression range is -60dB–
+20dB,soft knee adjustment is 0dB-+12dB, rate is 1:1, 1:10, LIMIT, start time is: 1-999ms, recovery time is
10-3000ms.
1
2
1
2

Digital Matrix Processor
9
THE FOURTH: LIMIT INTERFACE
1, Show compression status, level indicators and impression status of all channels.
2, Set the whole compression parameters for output channel, the compression range is -60dB–
+20dB, soft knee adjustment is 0dB-+12dB, rate is 1:1, 1:10, LIMIT, start time is: 1-999ms, recovery time is
10-3000ms.
THE FIFTH: DELAY INTERFACE
1, Show the delay parameter status of all channels.
2, Can adjust delay parameter of all channels, the scale is 0-680ms, there are millisecond, meter and feet
units for converting.
1
2
1
2

Digital Matrix Processor
10
THE SIXTH: MATRIX INTERFACE
1, Show connections of the device, users can enter and edit relevant channel by clicking the square , every
channel name is revisable.
2, All output channels can choose any input channels, and each route channel volume can be set alone.
THE : SEVENTH: GEQ INTERFACE
1. Display current channel GEQ curve status. When mouse pitching on the pushrod, the point of
GEQ curve will display the parameters.
2. Adjust the current channel 31 segment graphic equalizer parameter, select INA, INB, INC, IND
key on the right can enter different input channel interface.
1
2
1
2

Digital Matrix Processor
11
THE EIGHTH: INPUT INTERFACE
1, Select “Mag" interface, you can adjust the PEQ, High-cut, Low-Cut of the input channel, select
"PHASE" interface, you can adjust the current phase channel, also you can choose the non-current PEQ
and phase curve to show in sync.
2, Adjustable Gain, Mute, Q , Frequency, Type of all PEQ, Bypass key is optional, we can choose PEQ
style: Balance, High-shelf, Low-shelf, High-cut, Low-cut, Phase 180° , Phase 360°.
3, The Gain, Q, Frequency of PEQ can be adjusted by putter, and can be controlled by pressing the UP,
DOWN, LEFT, RIGHT key on the keyboard.
4, Low-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate: Butterworth, Bessel,
Linkwitz-Riley, the scale is: -6dB-- -48dB.
5, High-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate : Butterworth, Bessel,
Linkwitz-Riley, the scale is: -6dB-- -48dB.
6, The Gain, Mute, Phase of the input channel can control separately, as same as the level display Light.
1
2
3
4 5
6

Digital Matrix Processor
12
THE NINTH: OUTPUT INTERFACE
1. Select “Mag" interface, you can adjust the PEQ, High-cut, Low-Cut of the output channel, select
"PHASE" interface, you can adjust the current phase channel, also you can choose the non-current PEQ
and phase curve to show in sync.
2. Adjustable Gain, Mute, Q , Frequency, Type of all PEQ, Bypass key is optional, we can choose PEQ
style: Balance, High-shelf, Low-shelf, High-cut, Low-cut, Phase 180° , Phase 360°.
3. The Gain, Q, Frequency of PEQ can be adjusted by putter, and can be controlled by pressing the
UP, DOWN, LEFT, RIGHT key on the keyboard.
4. Low-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate: Butterworth, Bessel,
Linkwitz-Riley, the scale is:-6dB-- -48dB.
5. High-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate : Butterworth, Bessel,
Linkwitz-Riley, the scale is:-6dB-- -48dB.
6. The Gain, Mute, Phase of the output channel can control separately, as same as the level display
light.
1
2
3
4 5
6

Digital Matrix Processor
13
SPECIFICATION
System Specification
Frequency Response
20Hz~20kHz, -0.3dBu
S/N Ratio
Distortion(THD)
>115 dBu
<0. 005at1kHz(0dBu)
Cross-talk
<100dB below full scale
Input Section
Type
Balanced XLR
Max. Input Level
+18dBu
Impedance
1M/ Ω Stereo; 500k Ω/ MONO
Output Section
Type
Balanced XLR
Max. Output Level (bypass)
+20dBu
Impedance
<500 Ω
Digital Processing
24-bit sigma - delta converters
96kHz Sampling Rates
Display
20x2LCD Display For Parameters Setting And Function Select
Power Supply
AC~95V-264V FUSE 250VAC/2A FAST
Dimension (LxWxH)
48x24.5x4.5CM
Weight
2.62kg
ACCESSORIES
1. CD (Include PC software and user's manual).
2. One USB cord.
3. One electrical cord.

Digital Matrix Processor
14
REAR PANEL CONTROL PORT CONNECTION
1, Ethernet connection port: you can choose to connect the computer by wire, connect several devices by
switch, or use WIFI by router to control, but need to set different IP address and ID code for each device, or
they can' t connect successfully due to the IP addresses conflict.
SWITCH
ETHERNET
CONNECTION PORT
ROUTERR
ID:1
ID:2
2. RS232 connection port: Central control and connect to PC through RS232 port.
The 2PIN is: TXD, 3PIN
is:RXD, 5PIN is: GND
RS232/USB
CONVERTER
PC or laptop

Digital Matrix Processor
15
3. RS485 cascade contro port: Cascade connect several devices by RS485, you can choose different
ID to control separately.
PC or laptop
Connect several devices by cascading 7PIN and 8PIN of
the RS232 port, connect the computer through
RS485 converted RS232 switch, Cascade controllable
several devices after setting the different ID.
ID:1
ID:2
ID:3
The 7PIN is: RS485 D+ , 8PIN is: Rs485
D- of the RS232 port.

Digital Matrix Processor
16
Extend Remote control Protocol
1, Control package Format
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
Data1
Data2
Date3
STX
DLE
Packet
0x7B
0x7D
1～254
0x41～0x4A
0x??
0x??
0x??
0x7D
0x7B
2, Command Detail
(1) Gain Control(0x41)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
In/Out
Channel
+/-
STX
DLE
Packet
0x7B
0x7D
1～254
0x41
In: 0 Out:1
0~3
+:0,-:1
0x7D
0x7B
Example (increase input channel 1 gain): 7B7D01410000007D7B
(2) Mute Control(0x42)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
In/Out
Channel
No/Yes
STX
DLE
Packet
0x7B
0x7D
1～254
0x42
In:0 Out:1
0~3
No:0 Yes:1
0x7D
0x7B
Example (input channel 1 mute): 7B7D01420000017D7B
(3) Load Preset Control(0x43)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
Factory/User
Preset
0x30
STX
DLE
Packet
0x7B
0x7D
1～254
0x43
F:0 U:1
0～31
0
0x7D
0x7B
Example (recall user preset U00):7B7D01430100007D7B

Digital Matrix Processor
17
(4) Input Volume Control(0x44)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
Channel
HI-VOL
LO-VOL
STX
DLE
Packet
0x7B
0x7D
1～254
0x44
00～07
0x??
0x??
0x7D
0x7B
Example(InA volume +0.0dB): 7B7D01440001187D7B
(5) Output Volume Control(0x45)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
Channel
HI-VOL
LO-VOL
STX
DLE
Packet
0x7B
0x7D
1～254
0x45
00～07
0x??
0x??
0x7D
0x7B
Example (Out2 volume -3.0dB): 7B7D01450100FA7D7B
(6) Get Now Gain(0x48)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
In/Out
Channel
0x30
STX
DLE
Packet
0x7B
0x7D
1～254
0x48
In: 0 Out: 1
0～3
0
0x7D
0x7B
MCU Return:0x00 ～0x90=-60dB～+12dB,0.5dB/Step
Example (read input channel 1 gain parameter): 7B7D01480000007D7B
(7) Get Now Mute(0x49)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
In/Out
Channel
0x30
STX
DLE
Packet
0x7B
0x7D
1～254
0x49
In: 0 Out: 1
0～3
0
0x7D
0x7B
MCU Return:0x00 or 0x01=Un-Mute or Mute
Example (read input channel 1 mute parameter): 7B7D01490000007D7B

Digital Matrix Processor
18
(8) Get Now Preset(0x4A)
0
1
2
3
4
5
6
7
8
DLE
STX
Device
Assress
CMD
0x30
0x30
0x30
STX
DLE
Packet
0x7B
0x7D
1～254
0x4A
0
0
0
0x7D
0x7B
MCU Return:0x00～0x32=0: F00, 1～32: U00～U31
Example (read preset parameter):7B7D014A0000007D7B
Communication
parameter
Bits per second
115200
Stop bits
1
Data bits
8
Step
﹥= 20ms
Parity
None
ID
1