QMotion QIS User guide

REVISION 1.2 18JAN16 PN 9000233


Qadvanced Intelligent System (QIS)
Application Guide

2

REVISION 1.2 18JAN16
Qadvanced Intelligent System (QIS)
System Overview
PowerSupply:24VDC,7.5A
RJ‐45PortsforMotorizedShadesandSwitches‐Quanty8
CommunicaonPorts(RJ‐45)‐Quanty2
PN 9000233

3
REVISION 1.2 18JAN16
The Qadvanced Intelligent System offers three methods for Shade Control:
Hardwire control:
Uses standard Cat5e or Cat6 cable for both power and communication. Controlled via hardwired wall switches.
ZigBee HA1.2:
Uses standard Cat5e or Cat6 cable for power. Wireless communication via ZigBee HA1.2 specification. Supports
stand alone applications or ZigBee HA1.2 network applications that are easily integrated with 3rd party control sys-
tems.
RS485 Communication:
Uses standard Cat5e or Cat6 cable for both power and communication. 3rd party integration via RS485 Protocol.
Cat5e or Cat6 cables are not provided and must be purchased separately. Shielded wire may be used, but is not
required. For installations where the QIS cables may be in close proximity to other wiring, it may be advisable to use
shielded cables to protect against possible interference.
Qadvanced Intelligent System (QIS)
System Overview
PN 9000233
*Specificaonsaresubjecttochangewithoutnoce
Caution
NOTE: The Qadvanced Intelligent System does not operate on “standard” Power over Ethernet (PoE) schemes.
Do not attempt to connect the Qadvanced Intelligent System to any PoE device. Doing so may damage the system
components and/or the external Ethernet or PoE device.
SingleShade
HardwiredSwitch
DoubleShade
HardwiredSwitchPower/CommunicaonsPanel
12345
QdR
Mul‐Channel
Remote
RangeExtender
(Router)
Qube
(Coordinator)

MulpleShade
PowerSupply

***WallPlatesnotincludedwithHardwiredSwitch***
FitsstandardDecoratorWallPlate

4
REVISION 1.2 18JAN16 PN 9000233
Wire Specification:
 Category 5e/Category 6 for
use with RJ-45 Connector
 24 AWG
 Maximum length of wire from
Power/Communication Panel to
device:
- Up to an 8’ X 8’ Shade with
40:1 motor - 1250 feet
- 8’ X 8’ to 12’ X 12’ Shade with
73:1 motor - 750’ feet
- Hardwired 4 and 8 Button
Switches - 1000’ feet from
switch to farthest power panel
*Length based on 115K baud rate
 Maximum wire length for RS485
communication - 2000’ feet from
source to shade
Power/Communication Panel:
 8 RJ-45 ports for motorized
shades and switches
 2 additional RJ-45 commu-
nication ports dedicated to
daisy chain with other
Power/Communication Pan-
els and Third Party Integra-
tion via RS485.
 Power Supply
- AC Input: 100-240 VAC, 2.5A
- DC Output: 24 VDC, 7.5A
Note:
 Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown).
 Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window .
24 VDC
Power Supply
Power and
Communication Panel
24 VDC
Power Supply
RS485
Communication
Qadvanced Intelligent System (QIS)
Hardwired Switch Application
Hardwired
Switch
System Capacity:
 200 Devices (QMotion
Shades, QMotion Hardwired
Switches)
*Specificaonsaresubjecttochangewithoutnoce
Power and
Communication Panel

5
REVISION 1.2 18JAN16 PN 9000233
Power/Communication Panel:
 8 RJ-45 ports for motorized shades and switches
 2 additional RJ-45 communication ports dedicated to daisy chain with other Power/Communication
Panels and Third Party Integration via RS485.
 Power Supply
- AC Input: 100-240 VAC, 2.5A
- DC Output: 24 VDC, 7.5A
Note:
 Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown).
 Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window .
Qadvanced Intelligent System (QIS)
ZigBee HA1.2 Application
24 VDC
Power Supply
*Specificaonsaresubjecttochangewithoutnoce
Wire Specification:
 Category 5e/Category 6 for use with RJ-45 Connector
 24 AWG
 Maximum length of wire from Power/Communication Panel to device:
- Up to an 8’ X 8’ Shade with 40:1 motor - 1250 feet
- 8’ X 8’ to 12’ X 12’ Shade with 73:1 motor - 750 feet
- Hardwired 4 and 8 Button Switches - 1000 feet from switch to farthest power panel
*Length based on 115K baud rate
System Capacity:
 60 Devices (QIS Shades, QMotion Wireless Remotes, Qubes, and Range Extenders)
 Router capacity: 32 devices
Maximum Range: QIS ZigBee network devices have a 50 feet radius range. A network of devices can be
connected to create cumulative ranges that can span over hundreds of feet.
*Environmental conditions may affect individual results. All range dimensions are based on an unob-
structed environment or free range. There are a multitude of factors that can not be controlled by our
product that interfere with the range. Actual use in a home, office, or other space can expect lower
range, which can be augmented through the proper use of a Range Extender device.
QdR
Remote
Power and
Communication Panel
Qube
(Coordinator)
and / or
Range Extender
(Router)

6
REVISION 1.2 18JAN16 PN 9000233
Wire Specification:
 Category 5e/Category 6 for use with RJ-45 Connector
 24 AWG
 Maximum length of wire from Power/Communication Panel to device :
- Up to an 8’ X 8’ Shade with 40:1 motor - 1250 feet
- 8’ X 8’ to 12’ X 12’ Shade with 73:1 motor - 750 feet
- Hardwired 4 and 8 Button Switches - 1000 feet from switch to farthest power panel
*Length based on 115K baud rate
 Maximum wire length for RS485 communication - 2000 feet from source to shade
Power/Communication Panel:
 8 RJ-45 ports for motorized shades and switches
 2 additional RJ-45 communication ports dedicated to daisy chain with other Power/Communication
Panels and Third Party Integration via RS485.
 Power Supply
- AC Input: 100-240 VAC, 2.5A
- DC Output: 24 VDC, 7.5A
Note:
 Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown).
 Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window .
24 VDC
Power Supplies
RS485
Communication
Third Party
Integration
System Capacity:
 200 Devices (QIS Shades)
*Specificaonsaresubjecttochangewithoutnoce
Qadvanced Intelligent System (QIS)
Third Party Integration
Power and
Communication Panels

7
REVISION 1.2 18JAN16 PN 9000233
Qadvanced Intelligent System (QIS)
Third Party Integration with Hardwired Switch and ZigBee HA1.2
24 VDC
Power Supplies
24 VDC
Power Supplies
Hardwired
Switch
RS485
Communication
NOTE: The Qadvanced Intelligent System does not operate on “standard” Power over Ethernet (PoE) schemes.
Do not attempt to connect the Qadvanced Intelligent System to any PoE device. Doing so may damage the system
components and/or the external Ethernet or PoE device.
Caution
Third Party
Integration
QdR
Remote
Qube
(Coordinator)
and / or
Range Extender
(Router)
Power and
Communication Panels
Power and
Communication Panels

8
REVISION 1.2 18JAN16 PN 9000233
FCC
Warning: Changes or modifications to this device not expressly approved by QMotion®Incorporated -Advanced
Shading Systems could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equip-
ment should be installed and operated with minimum distance 20cm between the radiator and your body. This trans-
mitter must not be co-located or operating in conjunction with any other antenna or transmitter.
INDUSTRY CANADA
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'uti-
lisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
RF Exposure
Cet équipement est conforme aux limites ďexposition aux radiations dans un environnement noncontrôlé. Cet
équipement doit être installé et utilisé à distance minimum de 20cm entre le radiateur et votre corps. Cet émetteur ne
doit pas être co-localisées ou opérant en conjunction avec tout autre antenne ou transmetteur.