QSFPTEK S5300-24T4S User manual

S5300-24T4S Quick Start Guide
24-Port Fanless Gigabit Ethernet L2+ Switch
24x 10/100/1000BASE-T RJ45, with 4x 100/1000M SFP Uplinks,
Support Stacking
V1.0
www.qsfptek.com
V1.0
1／11

Introduction
The S5300-24T4S is a fanless RJ45 switch. Product positioning is to meet the requirements of
complex scenarios such as operator IP metropolitan area network, small and medium-sized
enterprise network, campus network, enterprise network and other networks. We appreciate your
decision to select S5300-24T4S. This manual is intended to help you become acquainted with the
switch design and provide instructions for implementing the switches into your network.
S5300-24T4S
Accessories
www.qsfptek.com
2／11
www.qsfptek.com
2／11
www.qsfptek.com
V1.0
2／11

Hardware Overview
FrontPanel Ports
S5300-24T4S
RJ45
Ports
Description
RJ45
1000BASE-T ports for Ethernet connection
SFP
Hot-swappable SFP ports for 1G connection
CLI port
An RJ45 console port for serial management
www.qsfptek.com
3／11
Console
SFP
www.qsfptek.com
3／11
www.qsfptek.com
V1.0
3／11

Front Panel LEDs
S5300-24T4S
Abbrev. Name
Description
PWR Power indicator
If the switch is powered on, the indicator is on.
System indicator
If the switch is started, the system indicator flickers.
Link/Act indicator
on each port
Always on in orange: 10/100M
Always on in green: 1000M
Off: no signal transmission
Always on in green: 1000M
Off: no signal transmission
Gigabit TX port 1-24
Keep the device powered on, press the button “Reset” for 6s, and
the system will return to the default setting.
Console port
It can be used to connect a computer or a terminal for
monitoring and configuring the switch.
Gigabit optical port
25S-28S
4 SFP interfaces
www.qsfptek.com
4／11
SYS
1-24
25S-28S Link/Act indicator
on SFP port
Reset
RJ45
Reset
24 gigabit TX ports
CLI
SFP
RJ45
Console
SFP
www.qsfptek.com
4／11
www.qsfptek.com
V1.0
4／11

Back Panel
S5300-24T4S
Grounding Point
Installation Requirements
Before youbegin the installation,make sure that you have the following:
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ45 Ethernet cables for connecting the network devices .
Site Environment:
Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged and
sufficient air circulation is provided for device cooling.
Avoid damage devices by following the electrostatic discharge prevention procedure.
Put the machine box in a place where cool air can blow off the heat inside the machine box. Make
sure the machine box is sealed because the opened machine box will reverse the cool airflow.
www.qsfptek.com
5／11
AC Power
www.qsfptek.com
5／11
www.qsfptek.com
V1.0
5／11

Mounting the switch
Connectingthe Power
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
Connecting the RJ45 Port
1. Plug a compatible RJ45 transceiver into the RJ45 port.
2. Connect anEthernet patch cable to the RJ45 transceiver. Then connect the other end
of the cable to another RJ45 device.
www.qsfptek.com
6／11
www.qsfptek.com
6／11
www.qsfptek.com
V1.0
6／11

Connecting the Management Port
Connecting the Console Port
1. Insert the RJ45 connector of the console cable into the RJ45 console port on the front of the switch.
2. Connect the other end of the console cable to the RS-232 serial port on the computer.
3. The console port of S5300-24T4S does not support traffic control. Therefore, you must set the option
data traffic control to none when you configure the switch with the super terminal. Otherwise, the single-
pass problem will arise on the super terminal.
Connecting the SFP Port
1. Connect SFP modules through the fiber to other Ethernet terminal devices.
2. Connect the other end of the cable to the SFP port on the front of the switch .
www.qsfptek.com
7／11
www.qsfptek.com
7／11
www.qsfptek.com
V1.0
7／11

Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step1: Connect the computer to the Management port of the switch using the network cable.
Step 2: Set the IP address of the computer to 192.168.0.x. ("x" is any number from 2 to 254.). Set the
subnet mask of the computer to 255.255.255.0.
www.qsfptek.com
8／11
www.qsfptek.com
V1.0
8／11
www.qsfptek.com
V1.0
8／11

Step 3: Open a browser, type http://192.168.0.2, and enter the default username and password, admin/
admin.
Step 4: Click sign in to display the web-based configuration page.
Configuringthe Switch Using the Console Port
Step 1: Connect a computer to the switch's console port using the supplied console cable.
Step 2: Start the terminal simulation software such as HyperTerminal on the computer.
Step 3: Set the parameters of the HyperTerminal: 9600 bits per second, 8 data bits, no parity, 1 stop
bit and no flow control.
Step 4: Enter the default username and password, admin/admin .
www.qsfptek.com
9／11
www.qsfptek.com
V1.0
9／11
www.qsfptek.com
V1.0
9／11

Troubleshooting
Loading FailureTroubleshooting
When encountering loading failures, the system may continue running in its original version. To address this
issue, users should first verify the physical port connections. In case of disconnected ports, reconnect them to
ensure proper physical connections and proceed with reloading. If the physical connections are correct, users
should then review the loading process information displayed on the super terminal for input errors. Any
identified input errors should be corrected before reloading the system.
UserPasswordLostTroubleshooting
If a user forgets or loses the system password, they can reset it using the following method:
1. Connect your computer to the switch's console port using a console cable.
2. Press the "ctrl + b" keys to enter the Uboot mode.
3. Start the system with an empty configuration file that has no password by entering the following
command: Bootrom#boot_flash_nopass
Bootrom#Do you want to revert to the default config file?[Y|N|E]:
Configuration SystemTroubleshooting
1. Confirm that the power supply is functioning properly and that the console cable is securely connected.
2. Verify that the console cable is the correct type for your system.
3. Check if the control cable driver is correctly installed on the computer. You may need to download and
install the appropriate driver from the manufacturer's website.
4. Confirm that the HyperTerminal parameters are correctly set. Ensure that the baud rate, data bits, stop
bits, and parity are properly configured according to your system's specifications.
username and password.
www.qsfptek.com
10／11
www.qsfptek.com
V1.0
10／11
www.qsfptek.com
V1.0
10／11

Support and Other Resources
Contct us
Email
Customer Success
https://www.qsfptek.com/company/contact-us.html
[email protected]
https://www.qsfptek.com/resources/customer-success-stories
Product Warranty
S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are
eligible to apply for a return or exchange of your items within 14 days of receiving them.
For more details about applying qualifications, please live chat or email [email protected] for support.
5 Year Warranty 14-day Return Window
www.qsfptek.com
V1.0
11／11