QSFPTEK S7600-24Y4C User manual

1／12
www.qsfptek.com
V1.0
V1.0
S7600-24Y4C Quick Start Guide
24-Port 25Gb Ethernet L3+ Switch
24x 25G SFP28, with 4x 100G QSFP28 Uplinks, Support MLAG

2／12
www.qsfptek.com
V1.0
Introduction
The S7600-24Y4C Switch is a high-performance 25G/100G switches. The product position is to
meet the requirements of next generation Enterprise, Data Center, Metro and HCI (Hyper-
Converged Infrastructure) networks.
We appreciate your decision to select S7600-24Y4C. This manual is intended to help you become
acquainted with the switch design and provide instructions for implementing the switches into your
network.
Accessories

3／12
www.qsfptek.com
V1.0
Hardware Overview
Front Panel Ports
Ports
Description
SFP28
SFP28 ports for 10G/25G connection
QSFP28
QSFP28 ports for 40G/100G connection
Back Panel Ports
Ports
Description
CON
An RJ45 console port for serial management
ETH
An RJ-45 Ethernet management port
USB
A USB management port for software and configuration backupand
offline software upgrade

4／12
www.qsfptek.com
V1.0
1G
10G
Front Panel LEDs
52
LEDs
Status
Description
ID
Blue
On
ID indication function enable
Off
ID indication function disable
SYS
Green
On
The system is normal running
Amber
On
The system occur alarm or error.
-
Off
No power or System is not run or abnormality
MGT
Green
On
Port link.
Off
Port not link.
SFP28
(Port 1-24)
Green
On
25G port link.
Blinking
25G packets receiving or transmitting.
Amber
On
10G/1G port link.
Blinking
10G/1G packets receiving or transmitting.
-
Off
Port not link
QSFP28
(Port 25-28)
Green
On
100G/40G port link.
Blinking
100G/40G packets receiving or transmitting.
Amber
On
10G/1G port link.
Blinking
10G/1G packets receiving or transmitting.
-
Off
Port not link
Breakout
Loop Blinking
One or more 100G/40G ports are breakout
Off
None of the 100G/40G port is breakout

5／12
www.qsfptek.com
V1.0
Back Panel
Installation Requirements
Tools Preparation
Flathead screwdrivers
Phillips screwdrivers
ESD-preventive wrist strap
Temperature/Humidity Requirements ：
Cleanliness Requirements ：
Substance
Unit
Concentration limit
DUST
Particle/m3
≤ 3 X 104 (No visible dust on the tabletop for three days)
SO2
mg/m3
0.2
H2S
mg/m3
0.006
NH3
mg/m3
0.05
Cl2
mg/m3
0.01
Note: The dust particle size is ≥ 5 μm
Temperature
Humidity
0~45°C
10%～95%

6／12
www.qsfptek.com
V1.0
Mounting the switch
Connecting the Power
1. Plug the AC power cord to the switch power port on the back rear.
2. Connect the other end of the power cord to a AC power source equipment.
Connecting the SFP28 Port
1. Insert the SFP28 module into the SFP28 port.
2. Plug a fiber patch cable to the SFP28 transceiver.
3. Connect the other end of the fiber to the device that you want to realize data
communication.

7／12
www.qsfptek.com
V1.0
Connecting the QSFP28 Port
1. Insert the QSFP28 module into the QSFP28 port.
2. Plug a fiber patch cable to the QSFP28 transceiver.
3. Connect the other end of the fiber to the device that you want to realize data
communication.
Connecting the Management Ports
Connecting the Console Port
1. Prepare an console cable.
2. Insert the RJ45 connector of the console cable into the console port on the switch.
3. Connect the D89 female connector on the other end of the console cable to the serial port on the
computer host.

8／12
www.qsfptek.com
V1.0
Connecting the ETH Port
1. Prepare an standard RJ45 Ethernet patch cable.
2. Insert one end of the RJ45 Ethernet patch cable to the computer RJ45 port.
3. Connect the RJ45 connector on the other end of the patch cable to the ETH port on the switch.
Connecting the USB Port
1. Prepare an Universal Serial Bus (USB) flash disk.
2. Insert the USB to the switch USB port.

9／12
www.qsfptek.com
V1.0
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.
Step 2: Set the IP address of the computer to 192.168.1.x (where "x" is any number from 2 to 254)
and the subnet mask to 255.255.255.0.
Step 3: Open a web browser and type http://192.168.1.2 in the address bar. Enter the default
username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.

10／12
www.qsfptek.com
V1.0
Configuring the Switch Using the Console Port
Step 1: Use the console cable to direct connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as HyperTerminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 115200 bits per
second, 8 data bits, no parity, 1 stop bit, and no flow control.
Step 4: Enter the default username and password (admin/admin).