QSFPTEK S5300-48T4X User manual

www.qsfptek.com v1.0
1/8
V1.0
S5300-48T4X Quick Start Guide
48-Port Gigabit Ethernet L3 Switch
48x 1G RJ45 Ports, with 4x 10G SFP+, Support Stacking

www.qsfptek.com v1.0
2/8
Introduction
The S5300-48T4X access switch features 48x GE RJ45 downlinks and 4x 10GE SFP+ uplinks. It supports stacking of up to two models,
making them logically regarded as one switch stack for interconnection and management.
We appreciate your decision to select S5300-48T4X. This manual is intended to help you become acquainted with the switch design
and provide instructions for implementing the switches into your network.
Accessories
Hardware Overview
Front Panel Ports

www.qsfptek.com v1.0
3/8
Ports
Description
RJ45
100/1000BASE-T ports for Ethernet connection
SFP+
SFP+ ports for 1G/10G connection
CON
A baud rate of 9600bps, RJ45 interface
Front Panel LEDs
LEDS
Description
SYS
If the SYS indicator flickers, the system works normally.
PWR
If the PWR indicator is always on, the device is powered on.
Back Panel
Abbrev
Name
Description
Grounding column
The grounding column
The grounding column must be fine.
Power supply
AC power supply
Input voltage: AC100~240V
Installation Requirements
Tools Preparation
Screwdriver
Static-proof wristband
Bolt
Ethernet cable

www.qsfptek.com v1.0
4/8
Other Ethernet terminal devices
Control terminal
Safety Principles
Keep dustless and clean during or after the installation.
Put the cover at the safe place.
Put tools at the right place where they are not easily falling down.
Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
Put on the protective glasses if the environment may cause damage to your eyes. Avoid incorrect operations that may cause
damage to human or devices.
Site Environment
Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged .
Avoid to damage devices by following the electrostatic discharge prevention procedure. S5300-48T4X Hardware Installation
Manual.
Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is
sealed.
Mounting the Switch
Connecting the Power
1. Plug the AC power cord to the switch power port on the back rear.
2. Connect the other end of the power cord to a AC power source equipment.

www.qsfptek.com v1.0
5/8
Connecting the RJ45 Ports
1. Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
2. Connect the other end of the Ethernet cable to the switch RJ45 port.
Connecting the SFP+ Ports
1. Insert the SFP+ module into the SFP+ port.
2. Plug a fiber patch cable to the SFP+ transceiver.
3. Connect the other end of the fiber to the device that you want to realize data communication.
Connecting the Management Ports
Connecting the Console Port

www.qsfptek.com v1.0
6/8
1. Prepare an console cable.
2. Insert the RJ45 connector of the console cable into the console port on the switch.
3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.
Step 2: Set the IP address of the computer to 192.168.0.x (where "x" is any number from 2 to 254) and the subnet mask to
255.255.255.0.
Step 3: Open a web browser and type http://192.168.0.2 in the address bar. Enter the default username and password (admin/admin).

www.qsfptek.com v1.0
7/8
Step 4: Click sign-in to access the web-based configuration page.
Configuring the Switch Using the Console Port
Step 1: Use the console cable to direct connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit,
and no flow control.
Step 4: Enter the default username and password (admin/admin).
Troubleshooting
Hardware Fault Analysis
Power and cooling systems—power and fan Port, cable and connection—ports on the front panel of the switch and the cables
connecting these ports
Faults Relative with Power and Cooling System
Do the following checkups to help remove the fault:
1. When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
2. if the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3
“Requirements for Common Locations”.
3. If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative with Port, Cable and Connection
Do the following checkups to help remove the fault:
1. If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
2. If the power on-off is at the “ON” location, check the power source and the power cable.

www.qsfptek.com v1.0
8/8
3. If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data
bits, no sum check bit, one stop bit and no traffic control.
Support and Other Resources
Contact us https://www.qsfptek.com/company/contact-us.html
Email [e-mail]
Customer Success https://www.qsfptek.com/resources/customer-success-stories
Product Warranty
S7600 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or
exchange of your items within 14 days of receiving them.
For more details about applying qualifications, please live chat or email [e-mail] for support.
5 Year Warranty 30-day Return Window