QSFPTEK S5300-24T6X User manual

www.qsfptek.com v1.0
1 / 10
V1.0
S5300-24T6X Quick Start Guide
24-Port Gigabit Ethernet L3 Switch
24x GE RJ45 Ports, 6x 10GE SFP+ Uplinks, Support Stacking

www.qsfptek.com v1.0
2 / 10
Introduction
The QSFPTEK S5300-24T6X Gigabit L3 switch has 24x 10/100/1000BASE-T RJ45 and 6x 10G SFP+ uplink ports. It delivers 168
Gbps switching capacity and 126 Mpps forwarding rate, features powerful stacking capability by supporting stacking up to 8 units,
providing higher network bandwidth and reliability.
We appreciate your decision to select S5300-24T6X. This manual is intended to help you become acquainted with the switch design a
nd provide instructions for implementing the switches into your network.
Accessories

www.qsfptek.com v1.0
3 / 10
Hardware Overview
Front Panel Ports
Ports
Description
RJ45 Port
RJ45 ports for 1G connection
SFP+ Port
SFP+ ports for 10G connection
CON Port
An RJ45 console port for serial management
Front Panel LEDs
LEDS
Description
PWR LED
If the switch is powered on, the PWR indicator is on
SFP LED
Gigabit Ethernet LINK/ACT LED
SFP+ LED
10Gigabit Ethernet LINK/ACT LED
SYS LED
If the system is started normally, the SYS indicator flickers

www.qsfptek.com v1.0
4 / 10
Back Panel
Abbrev
Name
Description
/
Grounding column
The grounding must be fine
/
Power Switch
ON means the power is switched on, while OFF means the power is cut off
POWER1
AC power supply
Input voltage AC100-240V
POWER2
AC power supply
backup power space
Installation Requirements
Tools Preparation
Screwdriver
Static-proof wristband
Bolt
Ethernet cable
Other Ethernet terminal devices
Control terminal
Safety Principles
Keep dustless and clean during or after the installation.
Put the cover at the safe place.
Put tools at the right place where they are not easily falling down.
Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
Put on the protective glasses if the environment may cause damage to your eyes.
Avoid incorrect operations that may cause damage to human or devices.
Site Environment
Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged and sufficient air circulation is
provided for device cooling.
Avoid to damage devices by following the electrostatic discharge prevention procedure.
Put the chassis at the place where cool air can blow off the heat inside the chassis. Make sure the machine box is sealed
because the opened machine box will reverse the cool air flow.

www.qsfptek.com v1.0
5 / 10
Mounting the Switch
Connecting the Power
1. Plug the AC power cord to the switch power port on the back rear.
2. Connect the other end of the power cord to a AC power source equipment.
Connecting the RJ45 Port

www.qsfptek.com v1.0
6 / 10
1. Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
2. Connect the other end of the Ethernet cable to the switch RJ45 port.
Connecting the SFP+ Port
1. Insert the SFP+ module into the SFP+ port.
2. Plug a fiber patch cable to the SFP+ transceiver.
3. Connect the other end of the fiber to the device that you want to realize data communication.

www.qsfptek.com v1.0
7 / 10
Connecting the Management Ports
Connecting the Console Port
1. Prepare an console cable.
2. Insert the RJ45 connector of the console cable into the console port on the switch.
3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.
Step 2: Set the IP address of the computer to 192.168.0.x (where "x" is any number from 2 to 254) and the subnet mask to
255.255.255.0.

www.qsfptek.com v1.0 8 / 10
Configuring the Switch Using the Console Port
Step 1: Use the console cable to direct connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit,
and no flow control
Step 3: Open a web browser and type http://192.168.0.1 in the address bar. Enter the default username and password (admin/admin)
.Step 4: Click sign-in to access the web-based configuration page.
.

www.qsfptek.com v1.0
9 / 10
Step 4: Enter the default username and password (admin/admin).
Troubleshooting
The key for resolving the systematic faults is to separate the fault from the system. You can compare what the system is doing with
what the system should do to detect the fault. You need to check the following subsystems:
Faults Relative with Power and Cooling System
Do the following checkups to help remove the fault:
Check whether the fan works normally. If the fan does not work well, check the fan.
If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section “Requirements
for Common Locations”.
If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative with Port, Cable and Connection
Do the following checkups to help remove the fault:
If the port of the switch can not be linked, check whether the cable is correctly connected and whether the peer connection is normal.
If the power switch is at the “ON” location, check the power source and the power cable.
If the console port does not work after the system is started up, check whether the console port is set to a baud rate of 9600 bps, eight
data bits, no sum check bit, one stop bit and no traffic control.

www.qsfptek.com v1.0
10 / 10
Support and Other Resources
Contact us https://www.qsfptek.com/company/contact-us.html
Email [e-mail]
Customer Success https://www.qsfptek.com/resources/customer-success-stories
Product Warranty
S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or
exchange of your items within 14 days of receiving them.
For more details about applying qualifications, please live chat or email [email protected] for support.
5 Year Warranty 14-day Return Window