QSFPTEK S5310-48P6X User manual

www.qsfptek.com v1.0
1 / 10
V1.0
S5310-48P6X Quick Start Guide
48-Port Gigabit Ethernet L3 PoE+ Switch
48x PoE+ Ports@740w , with 6x 10GE SFP+ uplink, Support Stacking

www.qsfptek.com v1.0
2 / 10
Introduction
The QSFPTEK S5310-48P6X has 48x 10/100/1000BASE-T ports supporting IEEE 802.3af/at(30w max) for powering attached wireless
access points, IP cameras, or other POE and POE+ standard terminal devices. And 6x 10GE SFP+ uplinks enable establish up to 60
Gbps links with the aggregation layer switch. It supports stacking up to eight S5300 series switches, making them logically regarded as
one for interconnection and management.
We appreciate your decision to select S5310-48P6X. This manual is intended to help you become acquainted with the switch design a
nd provide instructions for implementing the switches into your network.
Accessories

www.qsfptek.com v1.0
3 / 10
Hardware Overview
Front Panel Ports
Ports
Description
1G RJ TX Port
RJ45 port, with LINK/ACT indicators
10GE port
SFP+ port, with LINK/ACT indicators
CON Port
A baud rate of 9600bps, RJ45 port
Front Panel LEDs
LEDS
Description
SYS LED
If the SYS indicator flickers, the system works normally.
PWR LED
If the PWR indicator is always on, the device is powered on.
POE LED
Indicates whether the POE card is detected.
Back Panel
Abbrev
Name
Description
AC POWER1
AC power supply
Input voltage: AC100~240V
AC POWER2
AC power supply (Dual power backup)
Input voltage: AC100~240V
The grounding column
The grounding column
The grounding column must be fine.
1G RJ45 Port
10G SFP+ Port
CON Port
SYS LED
PWR
POE LED
Grounding Column
AC POWER2
AC POWER1

www.qsfptek.com v1.0
4 / 10
Installation Requirements
Tools Preparation
Screwdriver
Static-proof wristband
Bolt
Ethernet cable
Other Ethernet terminal devices
Control terminal
Safety Principles
The safety notices mentioned here means that improper operation may lead to body damage.
Read the installation guide carefully before you operate the system.
Only professionals are allowed to install or replace the switch.
Pull out the AC power socket before operating on the machine box or working beside the power source.
The final configuration of products must comply with relative national laws and regulations.
Site Environment
Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged and sufficient air circulation is
provided for device cooling.
Avoid to damage devices by following the electrostatic discharge prevention procedure.
Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is
sealed because the opened machine box will reverse the cool air flow.
Mounting the Switch
Connecting the Power
1. Plug the AC power cord to the switch power port on the back rear.
2. Connect the other end of the power cord to a AC power source equipment.

www.qsfptek.com v1.0
5 / 10
Connecting the RJ45 Port
1. Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
2. Connect the other end of the Ethernet cable to the switch RJ45 port.
Connecting the SFP+ Port
1. Insert the SFP+ module into the SFP+ port.
2. Plug a fiber patch cable to the SFP+ transceiver.
3. Connect the other end of the fiber to the device that you want to realize data communication.

www.qsfptek.com v1.0
6 / 10
Connecting the Management Ports
Connecting the Console Port
1. Prepare an console cable.
2. Insert the RJ45 connector of the console cable into the console port on the switch.
3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.

www.qsfptek.com v1.0
7 / 10
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.
Step 2: Set the IP address of the computer to 192.168.0.x (where "x" is any number from 2 to 254) and the subnet mask to
255.255.255.0.
Step 3: Open a web browser and type http://192.168.0.2 in the address bar. Enter the default username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.

www.qsfptek.com v1.0
8 / 10
Configuring the Switch Using the Console Port
Step 1: Use the console cable to direct connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit,
and no flow control.
Step 4: Enter the default username and password (admin/admin).

www.qsfptek.com v1.0
9 / 10
Troubleshooting
Hardware Fault Analysis
Power and cooling systems—power and fan
Port, cable and connection—ports on the front panel of the switch and the cables connecting these ports
Faults Relative with Power and Cooling System
Do the following checkups to help remove the fault:
1. When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
2. If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3
“Requirements for Common Locations”.
3. If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative with Port, Cable and Connection
Do the following checkups to help remove the fault:
If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
If the power on-off is at the “ON” location, check the power source and the power cable.
If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits,
no sum check bit, one stop bit and no traffic control.

www.qsfptek.com v1.0
10 / 10
Support and Other Resources
Contact us https://www.qsfptek.com/company/contact-us.html
Email [e-mail]
Customer Success https://www.qsfptek.com/resources/customer-success-stories
Product Warranty
S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or e
-xchange of your items within 14 days of receiving them.
For more details about applying qualifications, please live chat or email [e-mail] for support.
5 Years Warranty
30-days Return Window