qtran FLEX-MINI User manual

FLEX-MINI FLEX Light: Static White
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-26-21
Dimensions
Side bend
3.54" bending radius
.71"
.35"
HOUSING
COMPLIANT
The FLEX series is ideal for spaces where the light will be in direct view. As the name implies,
these LED lights are flexible and can be easily molded into dierent curvatures. The housing and
the lens allow for a perfect monochromatic light source with no hot spots. All of Q-Tran's FLEX
series fixtures are made with high-quality SMD LED chips, are UV and flame resistant and are
extremely energy-ecient.
The FLEX Mini Static White is available in a variety of dierent color temperatures ranging from
2200K to 5700K and can be specified with either PVC or Silicone construction.
Color Temperature (CCT)
Housing Color
2200K
White
2700K 3000K 3500K 4000K 5700K
LIGHT SOURCE
120º
BEAM ANGLE
Part Number Builder
- 2200K
- 2700K
- 3000K
- 3500K
- 4000K
- 5700K
22
27
30
35
40
57
• 1 year warranty on DIY connectors
• 2 year warranty on PVC
• 5 year warranty on silicone
• Impact rating of IK08
• IP67 rated when ordered with IP67 connectors
• Ambient temperature: -4ºF to +113ºF
• UV & Flame resistant construction
• No diode imaging
• PVC - standard
• Silicone - best for outdoor applications
3.28" increments
Nominal max
length: 59'
Illuminated
Length (in)
Connector
In
Connector
Out
Connector In
Orientation
Connector Out
Orientation
Connector In
Wire Length
Connector Out
Wire Length
CCTSeries
P
S
- PVC
- Silcone
FLM-SW
Product
Voltage:
24 VDC
FLM-SW
FLEX Mini
Static White
Watts/ftCRI
1.490
1.490
SW
SW
FC
EC
FC
FC
BC
SCL
SCR
EC
MT
JC
SM (PVC only)
FC
BC
SCL
SCR
MT*
JC*
SM (PVC only)
FC
BC
SCL
SCR
EC
MT
JC
FC
BC
SCL
SCR
MT*
JC*
FC
BC
SCL
SCR
1'
3'
10'
1'
3'
10'
N/A
SN
SN
IMIM
DIM
DIM
- Product length = illuminated length + connector length
- For factory assembled connector information, see page 2
- For DIY connector information, see page 3
- For compatible power supplies, see page 3
- For extrusion options, see page 4 (sold separately)
*Used in conjuction with Connector/Orientation Out
Up to 32 lm/ft
at 3000K
Injected-Molded Injected-Molded
Dual Injected-Molded
PVC only Dual Injected-Molded
PVC only
Snap
Snap
Swivel
Swivel

FLEX-MINI FLEX Light: Static White
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-26-21
Injected Molded Connectors - IP67 & IP68
INJECTED-MOLDED CONNECTOR - IP68 | SILICONE
DUAL INJECTED-MOLDED CONNECTOR - IP68 | PVC
Front Bottom Side (Right or Left) End cap Middle T-feed Jumper
DIM-FC DIM-BC DIM-SCR & DIM-SCL DIM-EC DIM-MT DIM-JC
Front Bottom Side (Right or Left) End cap Middle T-feed Jumper
IM-FC IM-BC IM-SCR & IM-SCL IM-EC IM-MT IM-JC
11.81” 11.81”
1.97”
11.81”
39.37”
118.11”
11.81” 11.81”
1.97”
11.81”
39.37”
118.11”
.39”
.73”
.71”
.12”
ø.39”
.59”
.59”
.85”
.79”
.39”
1.65”
.59”
.79”
.94”
1.65”
.16”
ø.59”
.47”
.65”
ø.39”
.08”
.73”
.39”
.73”
.65”
.08”
.53”
.87”
1.06”
.16”
.59”
.79”
1.65”
.16”
ø.59”
.85”
.39”
.73”
0.65”
ø.39”
.08”
INJECTED-MOLDED CONNECTOR - IP67 | PVC
.20”
.71”
.43”
.35”
ø.47”
.55”
.43”
.08”
.71”
.43”
.79”
.35”
0.08”
.43”
.55”
ø.47”
.71”
.35”
.08”
Front Bottom Side (Right or Left) End cap Middle T-feed Jumper Seamess Middle
IM-FC IM-BC IM-SCR & IM-SCL IM-EC IM-MT IM-JC IM-SM
11.81” 11.81”
1.97”
11.81”
39.37”
118.11”
.39”
.39”
.63”
0.08”

FLEX-MINI FLEX Light: Static White
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-26-21
SWIVEL CONNECTOR - IP20 | PVC & SILICONE
Front End Cap
SW-FC SW-EC
.41”
.73”
.24”
1.57”
.41”
.73”
.24”
1.57”
DIY Connectors - IP20 & IP67
NOTE: When specifying non-injected molded connectors, connectors will be sent separately from fixture to be applied in the field.
Compatible Power Supplies See website for additional power supply options
iQ-PHQZ QTM-DC+CAP QTM-eLED QOM-DC+CAP QOM-eLED
Q6M-DC+CAP Q-SET-eLED
SNAP CONNECTOR - IP67 | PVC & SILICONE
Front Bottom Side (Right or Left) End cap Middle T-feed Jumper
SN-FC SN-BC SN-SCR & SN-SCL SN-EC SN-MT SN-JC
2.07”
1.97”
.69”
.77”
.96”
2.30”
.69”
.43”
1.10”
.83”
.96”
2.30”
.69”
1.02”
.96”
1.10”
1.97”
.77”
.69”
.96”
11.81” 11.81”
1.97”
11.81”
39.37”
118.11”

FLEX-MINI FLEX Light: Static White
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-26-21
Compatible Extrusions and Clips
NOTE: All extrusions are field cuttable and can be used with either silicone or PVC housings.
1.5” length acts as a clip when used.
FLM-SELF-BD: Self-locking bendable serrated aluminum profile
Finish: Satin
Available lengths: 19.75", 39.5"
0.53"
0.86
"
0.26"
0.23"
0.98"
FLM-NONL: Non self-locking aluminum profile
Finish: Satin
Available lengths: 1.5", 19.75", 39.5", 79" 0.24"
0.46"
0.85
"
0.23"
0.98"
FLM-NONL-FL: Non self-locking flanged aluminum profile
Finish: Satin
Available lengths: 1.5", 19.75", 39.5", 79"
0.44"
0.71"
0.80"
0.83
"
0.25"
0.23"
0.98"
FLM-SELF-SR: Self-locking serrated aluminum profile
Finish: Satin
Available lengths: 1.5", 19.75", 39.5", 79"
0.22"
0.53"
0.86
"
0.23"
0.98"
FLM-SELF-FL: Self-locking flanged serrated aluminum profile
Finish: Satin
Available lengths: 1.5", 19.75", 39.5", 79"
0.53"
.91"
0.82"
0.86
"
0.22"
0.23"
0.98"

© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-08-21
INSTALLATION FLEX Light - FLEX Mini
NOTES:
• Field modifications must comply with Q-Tran’s installation methods otherwise warranty is null and void
Cautions
Bending
Wrong Approaches
1. Before making any cuts, installation, maintenance or connection, be sure the main power is disconnected.
2. Note: all connector joints must be connected correctly to achieve IP68 rating.
3. Please operate this fixture by instructions, and confirm the work voltage, it must be matched with product requirements.
4. Please confirm the polarity of connector before insertion front connection cable.
5. Connect and cut this product correctly. Any wrong operation will damage this product.
6. Use qualified DC power supply.
7. Please correctly use and bend this fixture.
8. Do not operate light when ambient temperature exceeds the range of specified temperature.
9. Do not energize the light over 30 minutes in coil packaging.
Do not bend smaller than allowed minimum bend diameter 3.94”.
3.94”
01 |0 2
(HB)Horizontal Bending
Light Surface
Twist the light
Light Surface
WARNING: The above wrong approaches will damage the light.
Light Surface
Light Surfac
e

© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-08-21
INSTALLATION FLEX Light - FLEX Mini
NOTES:
• Field modifications must comply with Q-Tran’s installation methods otherwise warranty is null and void
Instructions for Light Cutting
Cautions
1. Place the light horizontally when cutting it.
2. Use only factory-recommended cutter.
3. Cut the light according to the following instructions. Incorrect operation will damage the light.
C
uttingline
02
0102
Cut the light only at printed cutting line with
The min. cutting length
(See as the feature)
Cutting line
printing mark face upwards
The cutting surface must be flush
and smooth.
01 0 2
01 0 2
01
Don't cut slantingly
WARNING: The above mishandling will damage the light.
Cuttingline
Pri
nting mark should be faced upwards Cutting can only be made at the printed cutting line
Cutting Line
Printing Mark
Incorrect cutting may lead to water ingression

© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-08-21
INSTALLATION FLEX Light - FLEX Mini
NOTES:
• Field modifications must comply with Q-Tran’s installation methods otherwise warranty is null and void
Clasp Front Connector
Components Tools
Please ignore these steps if the front connector has been assembled before delivery.
NOTE:
1. Never wet the assembly units or assemble with wet hands.
2. Please use the tools correctly.
3. Please pay attention to personal security when using tools.
NOTE:
Installation steps are the same for Vertical and Horizontal Bending, even though the LED locations
are different.
Inducer Gripper
Feed Connector (1pc)
[Contain Silicone Gasket(1pc)]
A
nti-skidding Clip (1pc) U Steel Plate (1pc)
02
Finished Assembly View
Explosive View
Anti-Wicking Ferrule
The anti-wicking ferrule is located at 4.53" (±0.39" tolerance) from the connector on the cable.
For protection against water ingress from inside of cable wire and hence damage the light.
The removal of the anti-wicking ferrule will void the warranty.
NOTE: Unless otherwise stated, the tolerance is ±0.02". 1.18”
ø0.47”

© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-08-21
INSTALLATION FLEX Light - FLEX Mini
NOTES:
• Field modifications must comply with Q-Tran’s installation methods otherwise warranty is null and void
PCBInsertion Placement
PVC Tape
Insert the inducer to the backside of PCB around 0.39”-0.47”,
move the inducer up and down 3-5 times gently to create a
small cavity.
Insert the inducer into the backside of PCBIt will damage the light if inserted into fro
nt
side of PCB
Inser
t the feed connector pins into the
c
avity that you created with the
indu
cer (backside of PCB)
The following operations are prohibited:
Insert into the front side of the PCB Insert crosswise into the PCB Insert crosswise into the PCB
NEVER insert into the front side
(LED side) of the PCB
Clasp Front Connector
1. Inducing a Cavity for Feed Connector
2. Insert the Feed Connector

© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-08-21
INSTALLATION FLEX Light - FLEX Mini
NOTES:
• Field modifications must comply with Q-Tran’s installation methods otherwise warranty is null and void
Clasp Front Connector
3. Treatment of Anti-skidding clip
4. Installation for U Steel Plate
Unfold the anti-skidding clip about 20 degrees on both sides.
Fit the anti-skidding clip to the end of the light
tightly and align with the light end edge.
Place
the anti-skidding clip
onto the end of the light. Notice
its installation direction.
Push the bulging points on the anti-skidding
clip into the slots on the U steel plate.

© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-08-21
INSTALLATION FLEX Light - FLEX Mini
NOTES:
• Field modifications must comply with Q-Tran’s installation methods otherwise warranty is null and void
Clasp Front Connector
5. Push the anti-skidding clip to the end until the two hook splinters on each side pop out to lock the U steel plate. Use the gripper to help tighten the piece.
Please energize the light to check its
functionalit
y and do waterproof
r
eliablity testingafter connector assembly.