QualGear QG-TM-090-BLK User manual

Using an assistant, hang
the TV onto the wall plate
carefully by pushing the
buttom of the TV towards
the wall until the latches fit into the
wall plate rail. Then hide the two
safety straps at the back of the TV to
avoid pulling on it accidently, which
may cause the TV to release and fall.
PUSH
PULL DOWN TO RELEASE
WALL WALL
WALL WALL
Make sure the TV is safely
secured on the wall before releasing it.
Do not pull on the safety straps unless
you need to remove the TV. See
step 4 on how to safely remove the TV.
To remove the TV from the Wall Plate,
have an assistant hold the TV
while the other person pull the two
safety straps downward at the
same time to unlock the latches from
the wall plate rail. Then carefully lift
and remove the TV.
QG-TM-090-BLK
Removing the TV from the Wall Plate
60 100
100
200x200 300x300 400x200 400x400
600x400 800x400 800x600 900x600
Version September 2018Version September 2018
HEAVY DUTY FIXED TV WALL MOUNT
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
100kg100kg
(220lbs)
(220lbs)
RATEDRATED
Scan the QR Code™ below
for more info about this product:

Please read the entire installation manual before you start installation and assembly.
1 2
NOTE
WARNING
This product was designed to be installed on the following wall construction only:
WALL CONSTRUCTION HARDWARE REQUIRED
Wooden Stud Included
Wooden Beam Included
Solid Concrete Included
Other Contact Qualified Professional
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
[email protected] for replacement parts and do not start assembly and installation
until you receive all the parts.
Wall Plate (x1)
A
B
Adapter Bracket (x2)
Marking Template (x1)
C
Do not begin to install your QualGear product
until you have read and understood all the
instructions and warnings contained in this
installation manual. If you have any questions
regarding the instructions, for US customers
please contact QualGear customer support
via email at [e-mail]. For
all international customers, please contact
your local distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may cause
damage or serious injury. QualGear is not
liable for the improper use or installation of its
products.
Make sure that the supporting surface
will safely support the combined load of the
equipment and all attached hardware and
components.
Always use an assistant or mechanical
lifting equipment to safely lift and position the
equipment.
Tighten screws firmly, but do not over tighten.
Over tightening can damage the items, greatly
reducing their holding power.
ALL QUALGEAR products are intended for
indoor use only and any outdoor use voids the
limited warranty.
ALL QUALGEAR products are designed
and tested for residential use only and any
commercial use voids the limited warranty.
For warranty information, please visit
http://www.qualgear.com/warranty.php.
If mounting to wooden studs, make sure that
mounting screws are anchored into the center
of the studs. Use of an edge-to-edge stud finder
is highly recommended.
Never exceed the maximum rated weight
specified in this manual.
All bolts and screws must be used at the
designated points in the installation instructions
to prevent property damage and/or personal
injury.
DO NOT install near air conditioner vents or
where there is excessive dust or smoke.
When drilling holes in the wall, it is very
important to take care of electrical cables,
water, or gas pipes in the wall.
QG-TM-090-BLK
Bubble Level (x1)
D
Parts Checklist
Hardware Package
M4x14mm (x4)
M-A
M8x50mm (x4)
M-F
M5x14mm (x4)
M-B
M6x14mm (x4)
M-C
M8x20mm (x4)
M-D
5mm
Small Spacer (x8)
M-H
M6x30mm (x4)
M-E
15mm
Large Spacer (x8)
M-I
5.5mm/8.5mm
Washer (x4)
M-G
ST8x90mm
Lag Bolt (x6)
W-A
12x60mm
Concrete Anchor (x6)
W-B
D8 Washer (x6)
W-C

W-AW-C
SKIP TO STEP 2
34
For concrete wall mounting,
follow Step 1b.
NOTE
Using an edge-to-edge stud finder, find the
edges of the stud.
1
Using a level, mark the centerline of the stud.
2
NOTE Do NOT use power drill and do NOT over tighten the lag bolts.
WARNING
Make sure that mounting screws are anchored into the center of the studs. The use
of a stud finder is highly recommended.
Installers are responsible to provide hardware for other types of mounting situations.
 Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
Stud Finder
Using the marking template (C) provided,
mark six holes for drilling on the centerline
of the stud.
Using a power drill and 1/4" drill bit, drill pilot
holes of 1/4" (6 mm) diameter and at least
3.5" (90 mm) depth.
4
ø 6mm
90mm90mm
(ø 1/4")
3
Mount the wall plate (A) and tighten it with the
provided lag bolts (W-A) and D8 washers (W-C) using
a socket wrench.
5
()
(3.5")
3.5"
AWall Plate
QG-TM-090-BLK
C
D
Mounting to a Wooden Stud Wall
1a
DBubble Level

56
WARNING
 Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
Hold the marking template (C) provided against the wall where you want to install your TV,
mark six holes for drilling.
Using a power drill and a 1/2" masonry drill bit, drill mounting holes of 1/2" (12 mm) diameter
and 3.7" (95 mm) depth at the marked locations in the previous step.
1
2
ø 12mm
(ø 1/2") 3Place concrete anchors (W-B) in each hole. Tap each anchor flush with the wall using a hammer.
Using a socket wrench, mount the wall plate (A) and fasten them with the provided lag bolts
(W-A) and D8 washers (W-C).
NOTE Do NOT use power drill and do NOT over tighten the lag bolts.
W-B
W-A
W-C
AWall Plate
CMarking Template
DBubble Level
95mm
()
(3.7")
3.7"
95mm
the TV
QG-TM -090 -BLK
Mounting to a Concrete or a Brick Wall
1b
Top Backside of the TV

Installing to a Flat Back Panel of a TV
2a
78
Choose the appropriate screws and washers according to the
type of your TV, and attach adapter brackets (B) to the back of
the TV using a Phillips screwdriver.
Top of the TV
NOTE
Make sure the adapter
brackets are installed
in the correct direction.
5.5mm
8.5mm
OR
BAdapter Bracket
Flat Back
Panel
Top Backside of the TV
M-C/M-D
M-G
M-A/ M-B
M-G
IMPORTANT!
Tighten all screws but
do NOT over tighten

Top Backside of the TV
910
Choose the appropriate screws, washers, and spacers (if necessary) according to the type of your
TV and attach adapter brackets (B) to the back of the TV using a Phillips screwdriver.
IMPORTANT!
Tighten all screws but
do NOT over tighten
8.5mm
OR
Recessed
Back Panel
Curved
Back Panel
BAdapter Bracket
Top Backside of the TV
M-H
M-H
M-D/ M-E
M-G
Top Backside of the
M-E
M-G
M-I
Top Backside of the TV
M-E
M-G
M-H
Top Backside of the TV
M-I
Installing to a Curved or Recessed Back Panel of a TV
2b
OR
OR
OR
M-D
M-G
M-H
M-F
M-G
M-I
M-H
M-F
M-G
M-I
M-F
M-G
M-I
M-H