Quasar Science Q15W2060XG Installation instructions

|Quasar Science
Q-LED T12 CROSSFADE Lamps
1’ | 2’ | 4’ | 6’ | 8’
2000K-6000K
120VAC | 240VAC
Product Use & Safety
Instruction Manual
Version 0.1
Date: 7/3/2019
Author: Tim S. Kang
© 2019 Quasar Science, LLC. All rights reserved. Information subject to change without notice. Quasar
Science and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss,
consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on
the information contained in this document. The Quasar Science logo, the Quasar Science name, and all
other trade-marks in this document pertaining to services or products by Quasar Science or its affiliates
and subsidiaries are trademarks or licensed by Quasar Science or its affiliates or subsidiaries.
Quasar Science and the Quasar Science logo are registered trademarks of Quasar Science, LLC.
No part of this document may be used for distribution, reproduction, transmission, transcription, storage
in a data retrieval system, or translated into any language in any form by any means without the prior
written permission of Quasar Science, LLC. If you are downloading files from our web pages for your
personal use, make sure to check for updated versions. Quasar Science, LLC cannot take any liability
whatsoever for downloaded files, as technical data are subject to change without notice.

|Quasar Science
2
Dimensions
Length
Q15W2060XG: 1’ / 30.5cm pin tip to pin tip
Q25W2060XG: 2’ / 61cm pin tip to pin tip
Q50W2060XG: 4’ / 122cm pin tip to pin tip
Q75W2060XG: 6’ / 183cm pin tip to pin tip
Q100W2060XG: 8’ / 244cm pin tip to pin tip
Diameter
1.5” / 3.81 cm

|Quasar Science
3
Content
1. Dimensions
2. Safety Information
a. Risk Levels & Alert Symbols
b. Vital Precautions
c. Warnings
d. General Precautions
3. Introduction
a. Product description
b. Packing List
4. Overview
a. Device Diagram
b. AC Power Connector
5. Physical Installation & Power Instructions
a. Fixture installation configurations and instructions
b. Power requirements
6. Basic Features
a. Dimming
b. Dimming Equipment recommendations
7. Technical Specifications
a. Physical Length, Width Height
b. Diffusor Length, Width Height
c. Illuminant technical data
d. Photometric data
e. Spectral Data & Metrics
8. Warranty Information

|Quasar Science
4
Safety Information
1. Risk Levels & Alert Symbols
a. DANGER! indicates an imminent hazardous situation which, if not avoided, will
result in death or serious injury.
b. WARNING! indicates a potentially hazardous situation which, if not avoided,
may result in death or serious injury.
c. CAUTION! indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
d. NOTICE explains practices not related to physical injury. No safety alert symbol
appears with this signal word.
2. Vital Precautions
a. CAUTION! Lamps must receive their rated power!
i. 120VAC rated lamps must receive 110V-120V of AC power
ii. 240VAC rated lamps must receive 220V-240V of AC power
b. NOTICE Plugging 120VAC into 240VAC power will irreparably damage the lamp
driver electronics!
3. Warnings
a. CAUTION! The lamp does not have IP rating and must be kept dry at all
times.
b. NOTICE Do not use VARIAC type dimmers.
4. General Precautions
a. Make sure P1G power connector is firmly secure flush to the lamp end before providing
AC power.

|Quasar Science
5
Introduction
1. Product description
a. The Q15W2060XG, Q25W2060XG, Q50W2060XG, Q75W2060XG, and Q100W2060XG
Light Emitting Diode (LED) lamps are T12-sized LED bulbs containing a two strips of
LEDs emitting either 2000K or 6000K directly phosphor converted 450nm LEDs.
b. The LEDs are diffused through a 180odiffuser to provide an even illumination surface at
high enough frequencies to prevent flicker artifacts in photographic applications.
c. The LED diodes are “mixed” by changing the ratio of diode channel dim levels set by an
input CCT analog potentiometer and maintains maximum device wattage per CCT
setting.
d. The LEDs are dimmed through the use of external TRIAC AC dimmers.
2. Packing List
a. 1x T12-sized Lamp per product length
b. 1x P1G grounded bi-pin power connector

|Quasar Science
6
Overview
1. Device Diagram
a. The device has one control dial end and one G13 compatible bi-pin end with a hole for
the P1G grounding pin.
i. The control dial end (viewed from device front) contains an analog potentiometer
that dials in a 2000K & 6000K diode mix to achieve an indicated color
temperature of white light.
ii. The G13 compatible bi-pin end (viewed from device end) receives the P1G AC
power connector. The P1G grounding pin inserts into the ground pin port, while
the power pins insert into the P1G receiving holes.
2. P1G AC Power Connector
a. The P1G AC power connector has:
i. Male end: 1x polarized 3-prong AC connector
ii. Female end: 1x QTP3 head bi-pin receiver with spring tension buttons and
grounding pin
20—

|Quasar Science
7
Physical Installation & Power Instructions
1. Fixture installation configurations and instructions
a. The crossfade lamps will fit any typical T12 clips as well as Quasar Science T12-sized
Q-Block mounting blocks (QBK).
b. Quasar Plates or any other device containing T12 clips or T12 Q-blocks can mount
crossfade lamps. 4’ or larger lamps may need zip ties to additionally secure them into
the blocks.
c. To mount T12 lamps in these clips or Q-Blocks, simply insert the lamp into the clips until
it is fully secure.
2. Power requirements
a. To install the P1G AC connector:
i. Hold the power end with one hand.
ii. Pinch and hold the QTP3 spring tension buttons in with the other hand.
iii. Insert the grounding pin into the ground pin receiving hole and the G13 pins into
the QTP3 holes. Use the available thumb to push the QTP2 head flush to the
power end cap.
iv. Release the QTP2 spring tension buttons.
b. CAUTION! 120VAC rated lamps must receive 110V-120V of AC power
c. CAUTION! 240VAC rated lamps must receive 220V-240V of AC power
d. DC power sources will not power the lamp.
e. NOTICE Insufficiently powered AC dimming circuits may cause the lamp to flicker.
To remedy this issue, plug in parallel electrical configuration a very low wattage
incandescent light bulb to stabilize the TRIAC dimming circuit.

|Quasar Science
8
Basic Features
1. CCT control
a. Turn the analog CCT dial to the desired color temperature:
b. Color temperatures are shown divided by 100 (2000K/100 = 20, 3000K/100 = 30, etc) for
legibility and precision marking on the dial
2. Dimming
a. The Q-LED crossfade lamps are capable of dimming down while maintaining color
temperature.
b. The Q-LED crossfade lamps are dimmed by an external TRIAC AC source.
c. To Dim Q-LED crossfade lamps, plug the installed P1G into:
i. AC power wired up to a wall-dimmer switch
ii. AC power wired up to a TRIAC dimmer source
iii. AC power connected to a stand-a-lone TRIAC dimmer plugged into AC-power
3. Dimming Equipment recommendations
f. NOTICE The crossfade lamps must be dimmed with TRIAC AC dimming circuits.
VARIAC type dimmers will not work.
g. Reverse-phase (trailing edge) TRIAC AC dimming circuits will enable lower dim levels
with less potential strobing issues.
h. CFL/LED TRIAC AC dimming circuits must have a circuit that enables stable low voltage
operation.
i. The following dimmers work well with crossfade products:
i. Lutron CF line of household dimmers
ii. ETC Sensor
iii. RatPac dimmer products
20—

|Quasar Science
9
Technical Specifications
1. Physical Length, Width Height
a. Q15W2060XG, Q25W2060XG, Q50W2060XG, Q75W2060XG, and Q100W2060XG:
Width & height = 1.5” 3.81 cm
b. Q15W2060XG: 1’ / 30.5cm pin tip to pin tip
c. Q25W2060XG: 2’ / 61cm pin tip to pin tip
d. Q50W2060XG: 4’ / 122cm pin tip to pin tip
e. Q75W2060XG: 6’ / 183cm pin tip to pin tip
f. Q100W2060XG: 8’ / 244cm pin tip to pin tip
2. Diffusor Length, Width Height
a. Width = 1.5” 3.81 cm
b. Height = 0.75” 1.91 cm
c. Q15W2060XG length: 9 3/16” / 23.3cm
d. Q25W2060XG length: 20 5/8” / 52.4cm
e. Q50W2060XG length: 44 5/8” / 113cm
f. Q75W2060XG length: 68 5/16’ / 174cm
g. Q100W2060XG length: 92’ / 234cm
3. Illuminant technical data
a. Diode set 1: 2000K, duv = 0.0055 (2/3 to ¾Minus Green correction required for neutral
CCT)
b. Intermediary CCT: 3000K, duv = -0.007 (1/4 Plus Green correction required for neutral
CCT)
c. Diode set 2: 6000K, duv = 0.003

|Quasar Science
10
4. Photometric data
Model
Distance (ft)
2000K (FC /
Lux)
2800K (FC /
Lux)
3000K (FC /
Lux)
3200K (FC /
Lux)
4400K (FC /
Lux)
5600K (FC /
Lux)
6000K (FC /
Lux)
Q15XG
2 / 0.61
39 / 420
50 / 542
53 / 567
55 / 588
72 / 777
69 / 743
69 / 743
Q15XG
3 / 0.91
17 / 187
22 / 241
23 / 252
24 / 262
32 / 346
31 / 331
31 / 331
Q15XG
4 / 1.22
9.8 / 105
13 / 135
13 / 142
14 / 147
18 / 194
17 / 186
17 / 186
Q15XG
6 / 1.83
4.3 / 47
5.6 / 60
5.9 / 63
6.1 / 65
8 / 86
7.7 / 83
7.7 / 83
Q15XG
8 / 2.44
2.4 / 26
3.1 / 34
3.3 / 35
3.4 / 37
4.5 / 49
4.3 / 46
4.3 / 46
Q15XG
10 / 3.05
1.7 / 19
2.2 / 24
2.3 / 25
2.4 / 26
3.2 / 34
3 / 33
3 / 33
Q15XG
18 / 5.49
0.51 / 5.5
0.66 / 7.1
0.69 / 7.4
0.71 / 7.7
0.94 / 10
0.9 / 9.7
0.9 / 9.7
Q15XG
25 / 7.62
0.29 / 3.1
0.37 / 4
0.39 / 4.2
0.41 / 4.4
0.54 / 5.8
0.51 / 5.5
0.51 / 5.5
Q25XG
2 / 0.61
85 / 919
110 / 1185
115 / 1240
119 / 1286
158 / 1699
151 / 1626
151 / 1626
Q25XG
3 / 0.91
40 / 432
52 / 557
54 / 583
56 / 605
74 / 799
71 / 765
71 / 765
Q25XG
4 / 1.22
22 / 236
28 / 305
30 / 319
31 / 331
41 / 437
39 / 418
39 / 418
Q25XG
6 / 1.83
9.8 / 105
13 / 136
13 / 142
14 / 147
18 / 194
17 / 186
17 / 186
Q25XG
8 / 2.44
5.6 / 60
7.2 / 78
7.6 / 81
7.9 / 85
10 / 112
9.9 / 107
9.9 / 107
Q25XG
10 / 3.05
3.6 / 39
4.6 / 50
4.9 / 52
5 / 54
6.6 / 72
6.4 / 68
6.4 / 68
Q25XG
18 / 5.49
1.2 / 12
1.5 / 16
1.6 / 17
1.6 / 17
2.1 / 23
2 / 22
2 / 22
Q25XG
25 / 7.62
0.6 / 6.5
0.77 / 8.3
0.81 / 8.7
0.84 / 9
1.1 / 12
1.1 / 11
1.1 / 11
Q50XG
2 / 0.61
118 / 1273
153 / 1642
160 / 1718
166 / 1782
219 / 2355
209 / 2253
209 / 2253
Q50XG
3 / 0.91
60 / 642
77 / 829
81 / 867
84 / 899
110 / 1188
106 / 1137
106 / 1137
Q50XG
4 / 1.22
37 / 394
47 / 508
49 / 531
51 / 551
68 / 728
65 / 697
65 / 697
Q50XG
6 / 1.83
16 / 175
21 / 226
22 / 237
23 / 245
30 / 324
29 / 310
29 / 310
Q50XG
8 / 2.44
9.8 / 105
13 / 135
13 / 142
14 / 147
18 / 194
17 / 186
17 / 186
Q50XG
10 / 3.05
6.3 / 67
8.1 / 87
8.4 / 91
8.8 / 94
12 / 124
11 / 119
11 / 119
Q50XG
18 / 5.49
1.9 / 21
2.5 / 27
2.6 / 28
2.7 / 29
3.6 / 38
3.4 / 37
3.4 / 37
Q50XG
25 / 7.62
1.1 / 12
1.4 / 15
1.5 / 16
1.5 / 17
2 / 22
1.9 / 21
1.9 / 21
Q75XG
2 / 0.61
134 / 1444
173 / 1862
181 / 1949
188 / 2021
248 / 2671
237 / 2555
237 / 2555
Q75XG
3 / 0.91
79 / 853
102 / 1100
107 / 1151
111 / 1194
147 / 1577
140 / 1509
140 / 1509
Q75XG
4 / 1.22
51 / 551
66 / 711
69 / 744
72 / 772
95 / 1020
91 / 976
91 / 976
Q75XG
6 / 1.83
27 / 292
35 / 377
37 / 394
38 / 409
50 / 540
48 / 517
48 / 517
Q75XG
8 / 2.44
16 / 171
20 / 220
21 / 230
22 / 239
29 / 316
28 / 302
28 / 302
Q75XG
10 / 3.05
11 / 118
14 / 152
15 / 159
15 / 165
20 / 218
19 / 208
19 / 208
Q75XG
18 / 5.49
3.4 / 36
4.3 / 47
4.6 / 49
4.7 / 51
6.2 / 67
6 / 64
6 / 64
Q75XG
25 / 7.62
1.7 / 18
2.2 / 24
2.3 / 25
2.4 / 26
3.1 / 34
3 / 32
3 / 32
Q100XG
2 / 0.61
134 / 1444
173 / 1862
181 / 1949
188 / 2021
248 / 2671
237 / 2555
237 / 2555
Q100XG
3 / 0.91
87 / 934
112 / 1205
117 / 1261
122 / 1308
161 / 1729
154 / 1654
154 / 1654
Q100XG
4 / 1.22
61 / 656
79 / 846
82 / 886
85 / 919
113 / 1214
108 / 1161
108 / 1161
Q100XG
6 / 1.83
30 / 327
39 / 422
41 / 441
43 / 458
56 / 605
54 / 579
54 / 579
Q100XG
8 / 2.44
20 / 210
25 / 271
26 / 283
27 / 294
36 / 388
35 / 372
35 / 372
Q100XG
10 / 3.05
13 / 143
17 / 184
18 / 193
19 / 200
25 / 264
24 / 253
24 / 253
Q100XG
18 / 5.49
4.1 / 45
5.3 / 58
5.6 / 60
5.8 / 62
7.7 / 82
7.3 / 79
7.3 / 79
Q100XG
25 / 7.62
2.1 / 23
2.7 / 29
2.8 / 31
2.9 / 32
3.9 / 42
3.7 / 40
3.7 / 40