Quasar LINCOLN Series User manual

LINCOLN Remote Control System
DS-LINCOLN-2
Description
The LINCOLN is a versatile general purpose remote control, which can be used for controlling man
different applications
Supplied read to go, the receiver contains changeover contact rela s that are eas to connect via
screw terminals.
AM Remote Control
100 metres Range
1 or 4 channel variants
High Sec rity 1 Million possible
Addresses
4 x Relay O tp ts
Latch/Momentary Option
‘Easy Learn’
CR2016 battery
Part N mberPart N mber DescriptionDescription
FreqFreq
(MHz)(MHz)
Range**Range**
(Metres)(Metres)
LINCOLN-4S1 1 channel S stem 433 100
LINCOLN-4S4 4 channel S stem 433 100
LINCOLN-4T1 1 channel Transmitter Ke fob 433 100
LINCOLN-4T4 4 channel Transmitter Ke fob 433 100
* Range stated is optimal, in some conditions this ma be dramaticall reduced.
Applications
• General Purpose Remote Switching
• Electric Gates
• Roller Shutter Doors
• Garden Lighting

DS-LINCOLN-2
LINCOLN Remote Control System
Connecting the Receiver Unit
Each Channel output rela provides an isolated changeover Contact. Outputs 2 to 4 Connections are
Common (COM) and Normall Open (NO) which close together when activated. Output 1 has an addi-
tional Normall Closed (NC) changeover contact.
The action of the rela outputs is set b the Option link setting Jumper. A link is made / removed b the
small shorting link ‘cap’ placed over the pin header.
LINCOLN-4S1 Receiver Circuit board LINCOLN-4S1 Receiver Circuit board
Link Postion Controls O tp ts
Fitted 1Fitted 1- -2= 2= Momentar Momentar
Fitted 2Fitted 2- -3= 3= Latching Latching
Not Fitted = Not Fitted = FlipFlop FlipFlop
Momentary : The rela is activated for as long as transmitter button pressed.
Latching : The rela toggles between On / Off each button press.
FlipFlop : Rela s 1 & 2 and 3 & 4 operate in pairs.
When button 1 is pressed rela 1 switches on, Rela 2 Switches off
When button 2 is pressed rela 2 switches on, Rela 1 Switches off
Rela 3 & 4 operate in the same manor to Transmitter buttons 3 & 4.
Learning a New Transmitter Keyfob
Briefl Press the “Learn Switch” on the receiver PCB, the receiver LED will illuminate.
Press an transmitter button once, the receiver LED will flash 3 times.
This transmitter will operate the s stem.
Erasing Existing Transmitters
Press and hold the receiver “Learn Switch”, the receiver LED illuminates.
When the LED extinguishes (5-10 seconds) the Receiver is erased.
NOTE: You can not erase individual Tx encoders
NOTE: maximum of 45 button pairings per receiver

DS-LINCOLN-2
LINCOLN Remote Control System
Enclosure dimensions:
LINCOLN-4S1 LINCOLN-4S4
1 Rela Rx 33 x 81mm 4 Rela Rx 54 x 74mm
Technical SpecificationsTechnical Specifications
LINCOLN Transmitter Key fob
Batter T pe CR2016 (supplied)
Dimensions 59 x 34 x 12mm
Changing the battery
Remove the front panel from the back b carefull pushing a flat screwdriver down the side to separate the en-
closure. Open the case and change the batter . Ensure ou check the orientation.
ELECTRICAL CHARACTERISTICS MIN TYPICAL MAX DIMENSION
Suppl Voltage for +12Vd 11 12 13 Vdc
Suppl Current: Quiescent
All rela s operating S1
All rela s operating S4
11
45
210
mA
mA
mA
Rela Rating** A
Encoding S stem number of Combinations 1 Million
Operating Temperature -20 +80 degC
Receiver Sensitivit -105 dBm
**Please Note: The rela contacts in this unit are for functional use onl and must not be used for isolation purposes
Transmitters:
LINCOLN-4T4 LINCOLN-4T1

DS-LINCOLN-2
LINCOLN Remote Control System
SIMPLIFIED EU DECLARATION OF CONFORMITY
The simplified EU declaration of conformit referred to in Article 10(9) shall be provided as follows:
Hereb , QuasarUK declares that this radio equipment is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformit is available at the following Location:
http://www.quasaruk.co.uk/acatalog/Quasar-CE-Compliance-Certificates-.html
Q asar k Ltd. Recycling Notice
Meets the following EC Directives:
DO NOT
Discard with normal waste, please rec cle.
ROHS Directive 2002/95/EC
Specifies certain limits for hazardous substances.
WEEE Directive 2002/96/EC
Waste electrical & electronic equipment. This product must
be disposed of through a licensed WEEE collection point. RF
Solutions Ltd., fulfills its WEEE obligations b member- ship
of an approved compliance scheme.
Waste Batteries and Acc m lators
Directive 2006/66/EC
Where batteries are fitted, before rec cling the
product, the batteries must be
removed and disposed of at a licensed
collection point.
Environment Agenc producer registration
number: WEE/JB0104WV.
Disclaimer:
Whilst the information in this document is believed to be correct at the time of issue, QuasarUK Ltd does not accept an liabilit whatsoever for its accurac , adequac or completeness. No
express or implied warrant or representation is given relating to the information contained in this document. QuasarUK Ltd reserves the right to make changes and improvements to the product
(s) described herein without notice. Bu ers and other users should determine for themselves the suitabilit of an such information or products for their own particular requirements or specifica-
tion(s). QuasarUK Ltd shall not be liable for an loss or damage caused as a result of user’s own determination of how to deplo or use QuasarUK Ltd’s products. Use of QuasarUK Ltd prod-
ucts or components in life support and/or safet applications is not authorised except with express written approval. No licences are created, implicitl or otherwise, under an of QuasarUK Ltd’s
intellectual propert rights. Liabilit for loss or damage resulting or caused b reliance on the information contained herein or from the use of the product (including liabilit resulting from
negligence or where QuasarUK Ltd was aware of the possibilit of such loss or damage arising) is excluded. This will not operate to limit or restrict QuasarUK Ltd’s liabilit for death or
personal injur resulting from its negligence.