QUATROS QS19122 User manual

a
a
PW TECHSAM Woch Sp. J. tel. [phone]
ul. Warszawska 131 tel. [phone]
20-824 Lublin fax [phone]
www.quatros.eu e-mail: [email protected]
IMPORTER:
OWNER’SMANUAL
HYDRAULIC TROLLEY JACK 2T
QS19122
DESCRIPTION
Hydraulic Trolley Jack 2T QS19122: Capacity: 2T |Min. height: 125mm | Max. height: 300mm | Weight: 6,5kg
SAFETY INSTRUCTIONS
WARNING
-This jack is a lifting device, designed ONLY for lifting part of the total vehicle (i.e one wheel). Do not move or dolly the
vehicle while itis on the jack. Never use lift device to raise any others load.
-Position this jack to ONLY lift on the areas of the vehicle as specified by the vehicle manufacturer.
-After lifting the vehicle, ALWAYS support the load with appropriately rated vehicle support stands BEFORE working on the
vehicle.
-Do not overload this jack beyond its rated capacity. Overloading can cause damage to or failure of the jack.
-This jack is designed ONLY for use on hard level surfaces capable of sustaining the load. Use on other than hard level
surfaces can result in jack instability and possible loss of load.
-Center load on jack saddle BEFORE lifting vehicle. Off-center loads and loads lifted when the jack is not level can cause loss
of load or damage to the jack.
-Study, understand and follow all instructions in this manual BEFORE operating the jack.
-Failure to heed this warning may result in loss of load, damage to the jack and/or jack failure resulting in personal injury or
property damage.
OPERATION
WARNING! Ensure that you read, understand and apply the safety instructions.
OPERATING INSTRUCTIONS
1. Assemble handle front section to larger section using pin provided.
2. When this jack leaves the factory for shipment. The vent plug on top of the oil chamber is closed to prevent the oil from
being spilled. Also, the oil chamber contains the right amount of oil before shipment. Before using for the first time,
remove cover plate, unscrew vent plug until there is 1/16” gap. If oil spill is evident. Or if vent plug was found open it is
necessary to check oil level before pumping.
3. With release valve open, pump handle about 6 full strokes to assure complete distributor of oil.
4. Close release valve and jack is ready to use.
5. Always center the load on a saddle of jack. Off-center loads and loads lifted while jack is not sitting level may damage the
jack.
BEFORE USE
During shipment or handling air in jack can become trapped in the hydraulic system causing jack to malfunction. To release air from
the hydraulic system:
1. Turn release valve counter-clockwise with handle no more than two full turns.
2. Remove oil fill plug.
3. Pump jack handle quickly in several full strokes.
4. Repeat above steps as needed. Remember to replace oil fill plug.

a
a
PW TECHSAM Woch Sp. J. tel. [phone]
ul. Warszawska 131 tel. [phone]
20-824 Lublin fax [phone]
www.quatros.eu e-mail: [email protected]
IMPORTER:
TO RISE
1. With one end of jack handle, close release valve tightly by turning it clockwise.
2. Place vehicle in PARK (in gear on standard transmission) and apply emergency brake.
3. Place jack under vehicle at proper lifting location. (Refer to vehicle Owner’s Manual). If needed, turn extension screw on
jack counter clockwise until it comes in contact with vehicle.
4. Insert jack handle into handle socket. Pump the handle to lift vehicle to desire heights.
TO LOWER
1. Remove handle use small end to SLOWLY open release valve. To open, turn SLOWLY in counter-clockwise direction.
2. When vehicle fully lowered, remove jack. If extension screw has been extended, turn it clockwise until it retracts enough to
remove from vehicle.
3. When jack has been removed from vehicle, close release valve for storage.
GENERAL CARE
-When jack is not in use lifting arm and pump lever should be in full down position. This will protect precision machined
surface of the arm and the piston from corrosion.
-Container is filled with 7fl.oz of hydraulic jack oil.
-Keep your jack clean and well lubricated as well as the outside moving parts such as the lifting arm spindle, wheel bearings
and cross head pin.
-Should any other parts be required please refer to the sectional drawings and quote appropriate serial number of the jack
when ordering.
-ADDING OIL: With arm fully lowered and jack on level ground, remove oil fill plug. Add oil if level is more than ½” below
hole replace cover plate.
-REPLACING OIL: Oil should be replaced at least once a year. To drain oil, remove cover plate. Oil filler plug and release valve.
Be VERY CAREFUL to not allow dirt and any foreign matter into the system.
-LUBRICATION: Put grease in fitting on base and lubricate lifting arm spindle with oil every 3 months.
-RUST PREVENTION: Clean and wipe with oily cloth the piston ram and pump piston every 3 months or when signs of rust or
corrosion appear. When not in use always leave the saddle and pump piston in the completely down position.
TROUBLE
CAUSE
REMEDY
Jack will not lower completely
1. Air in hydraulic system
2. Release valve stuck
1. Purge air from hydraulic system
2. Transfer weight load and clean
valve
Jack will not lower weight
1. Release valve in open
position
1. Close release valve tightly
Jack will not lift to full height
1. Oil level low
2. Air in hydraulic system
1. Fill to recommended level
2. Purge air from hydraulic system
Weak lifting
1. Air in hydraulic system
2. Dirty oil
3. Release valve not
completely closed
1. Purge air from hydraulic system
2. Change oil use SAE 5W
3. Close release valve tightly
Jack will not lift
1. Excessive weight
2. Release valve in open
position
3. Oil level low
1. Decrease weight or change to
higher capacity jack
2. Turn valve clockwise and tighten
3. Fill to recommended level

a
a
PW TECHSAM Woch Sp. J. tel. [phone]
ul. Warszawska 131 tel. [phone]
20-824 Lublin fax [phone]
www.quatros.eu e-mail: [email protected]
IMPORTER:
WARRANTY CONDITIONS
1. P.W. TECHSAM Woch Sp. J. with its registered office in Poland at Lublin, 131 Warszawska Av. guarantees the highest quality of
Quatros tools and workshop equipment. Warranty period for products is 12 months from purchase date excluding batteries being
part of tools for which warranty period is 6 months from purchase date.
2. This warranty does not apply to normal wear and tear of spare parts or any damage caused by improper maintenance (including
overloading of tool, using power tools with hand-operated tools, inefficient thread greasing etc.).
3. Complaint shall be filed at place where the tool was bought.
4. Faulty tool or equipment is repaired or replaced in 14 days from date of its receive unless additional expertise written by
manufacturer or expert is needed or replaced tool/part has to be delivered from manufacturer or unexpected occurrence like flood,
conflagration, strike, natural disease, embargo, break in production etc. takes place.
5. In case of sets warranty is limited to repair or replacement only complained part of the set, not whole set.
6. Due to specific working conditions this warranty does not apply to:
-hand-operated bits and socket bits, power bits and power socket bits,
-screwdrivers if type of damage is caused by using with inappropriate screw size or overloading.

Lublin, 01.07.2021
DECLARATION OF CONFORMITY
PW TECHSAM WOCH SP. J.
Al. Warszawska 131
20-824 Lublin
We hereby declare that:
Hydraulic Trolley Jack 2T
QUATROS QS19122
Is conformal to 2014/30/EU directive and fulfils requirements of following standards:
EN ISO 12100:2010, EN 349:1993+A1:2008, EN ISO 14120:2015, EN ISO 13857:2008
Is identical to product which is subject to EC type examination by:
Ente Certificazione Macchine Srl
Via Mincio, 386/a
41056 Savignano s./P. (MO) –ITALY
tel [phone]
fax [phone]
e-mail: [email protected]
Certificate no. 0B190320.JOMQ062
In case of unauthorized modifications to the product this declaration becomes invalid.
Person authorized to compile the technical file:
Marcin Puderecki
(Name)