QUATROS QS19311 User manual

a
a
PW TECHSAM Woch Sp. J. tel. [phone]
ul. Warszawska 131 tel. [phone]
20-824 Lublin fax [phone]
www.quatros.eu e-mail: [email protected]
IMPORTER:
OWNER’SMANUAL
HYDRAULIC SHOP PRESS 10T
QS19311
DESCRIPTION
Hydraulic Shop Press 10T QS19311: Capacity: 10T | Working range: 0 - 375mm |Weight: 50,5kg
Hydraulic Shop Press 10T with multi-position bed for work height adjustment used for parts straightening, bending and pressing.
SAFETY INSTRUCTIONS
WARNING
-This press is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with
the proper and safe operation of a hydraulic press, do not use until proper training and knowledge has been obtained.
-Do not operate this press beyond it rated capacity.
-DO NOT compress springs or other objects that could be ejected from the press. DO NOT compress objects that could
shatter.
-Check the press for loose or damaged parts before each operation. Replace damaged parts and tighten all loose bolts
before operating.
-Some parts being pressed may have a tendency to pop out of the press or explode under pressure. Protect yourself
accordingly.
OPERATION
WARNING! Ensure that you read, understand and apply the safety instructions.
OPERATION
1. Place work piece on bed frame.
2. Locate and close release valve.
3. Pump handle until the ram nears work piece.
4. Apply load to work piece by pumping handle. Do not overload work piece.
5. Remove load from work piece by turning release valve. Stabilize work piece so it does not fall while pressure is released.
6. Remove work piece after ram is fully retracted.
MAINTENANCE
-Periodically, lightly oil all moving parts including the
pump piston and hydraulic ram.
-Check hydraulic connections and hoses before each use.
Do not use if cut, damaged, leaking or otherwise
damaged connections and/or hoses are notes.

a
a
PW TECHSAM Woch Sp. J. tel. [phone]
ul. Warszawska 131 tel. [phone]
20-824 Lublin fax [phone]
www.quatros.eu e-mail: [email protected]
IMPORTER:
WARRANTY CONDITIONS
1. P.W. TECHSAM Woch Sp. J. with its registered office in Poland at Lublin, 131 Warszawska Av. guarantees the highest quality of
Quatros tools and workshop equipment. Warranty period for products is 12 months from purchase date excluding batteries being
part of tools for which warranty period is 6 months from purchase date.
2. This warranty does not apply to normal wear and tear of spare parts or any damage caused by improper maintenance (including
overloading of tool, using power tools with hand-operated tools, inefficient thread greasing etc.).
3. Complaint shall be filed at place where the tool was bought.
4. Faulty tool or equipment is repaired or replaced in 14 days from date of its receive unless additional expertise written by
manufacturer or expert is needed or replaced tool/part has to be delivered from manufacturer or unexpected occurrence like flood,
conflagration, strike, natural disease, embargo, break in production etc. takes place.
5. In case of sets warranty is limited to repair or replacement only complained part of the set, not whole set.
6. Due to specific working conditions this warranty does not apply to:
-hand-operated bits and socket bits, power bits and power socket bits,
-screwdrivers if type of damage is caused by using with inappropriate screw size or overloading.

Lublin, 01.07.2021
DECLARATION OF CONFORMITY
PW TECHSAM WOCH SP. J.
Al. Warszawska 131
20-824 Lublin
We hereby declare that:
Hydraulic Shop Press 10T
QUATROS QS19311
Is conformal to 2006/42/EC directive and fulfils requirements of following standards:
EN ISO 12100:2010
Is identical to product which is subject to EC type examination by:
Ente Certificazione Macchine Srl
Via Mincio, 386/a
41056 Savignano s./P. (MO) –ITALY
tel [phone]
fax [phone]
e-mail: [email protected]
Certificate no. EC.19852.0D190306.JOM0659
In case of unauthorized modifications to the product this declaration becomes invalid.
Person authorized to compile the technical file:
Marcin Puderecki
(Name)