Quoizel BEC9009SBK Mounting instructions

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2017 QuoizelInc.
Assembly Instruction Sheet #IS-BEC9009SBK_R2
For Style BEC9009SBK
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
RevisedDate:2017-05-08
Pleasegoto forproductcleaningtips.Gotothe selection.www.quoizel.com Care + Maintenance
ToolsRequired:
LightSource:
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated14WLED
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
EstimatedAssemblyTime:
Preparation:
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Package Contents
A
Mounting
Screw
x3
Fixture
Body
x1
B
Fxture
Hood
i
C
D
STEP 1 Install Glass-
A. Unscrew the Mounting Screw,
remove the i from
the Fixture Body (B).
B. Insert Glass Panels (D/C) into
slots in the bottom edge of the
Cage. Fold Tabs on the top edge
of the Cage to secure Glass
Panels.
C. Attach the Cage with Glass
Panels back onto fixture hood
and secure by threading the
Mounting Ball onto the Bolts.
Hand tighten until snug.
F xture Hood
C
D
Cage
Front/Back
Glass Panel
x2
Side Glass
Panel
x2
Mounting
Ball
Figure 1
STEP 2 -Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter Marking Pen
Mounting
Hole
Post
Lighting
Post
Post
Fixture
Fitter
Figure 2
STEP 3 M C E M H-arking the enter of ach ounting ole
A. Remove the light fixture. Using the center punch and hammer
marking the center of each mounting hole location that is marked
with the marking pen.
Center Punch
Hammer
Marking
STEP 4 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 5 above.
1/16” bit and drill
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Post
Post
Figure 3
Figure 4
Figure 5

2of2
2017 QuoizelInc. RevisedDate:2017-05-08
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 6 Attach the fixture to the Post Mount-
A. Place the fixture on the post lining up the mounting holes on the
fixture fitter with the holes on the post. Use the Mounting Screws (A)
to attach the fixture to the post.
Your fixture is now assembled and ready to use.
Enjoy!
Post
Hole
Fixture Fitter Mounting
Hole
Post
Lighting
A
Figure 6
BEC9009SBK
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
FINISH: STONE BLACK
?16
8”
9”
18.5”