Quoizel EVG8409EK Mounting instructions

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-EVG8409EK
For Style EVG8409EK
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
ACrossbar Assembly
x1
C
Fixture
Body
x1
STEP 2 -Attach Cage to Fixture Body
A. Place the top edge of the Cage (D)
over bolts on the bottom edge of the
fixture hood on the Fixture Body (C).
Secure by threading Lock Balls (E)
onto bolts. Hand tighten until snug.
Figure 2
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBaseBulb100WMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
DCage
x1
ELock Ball
x2
C
D
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2016-08-15
B
Alternate
Mounting screw
x2
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
A
Mounting Screw
or Alternate Short
Mounting Screw
E
STEP 3 Test Fitting Backplate
to Crossbar Assembly
-
A.
on Fixture Body
(C)tothe
Remove mounting balls from
the Crossbar Assembly (A). Fit
the backplate
Crossbar Assembly
(A) and secure with mounting
balls. Note: The backplate
should be snug
against the wall and the
mounting balls. If
on
Fixture Body (C)
not, adjust the
length of the mounting screws
or alternate short mounting
screws on the Crossbar Figure 3
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
C
Assembly (A) by unscrewing the preassembled hex nut and lock
washer and then screwing the mounting screws or alternate short
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate on Fixture Body (C) is secure, remove
the mounting ball and Fixture Body (C) and proceed to Step 4.
Mounting Screw
or Alternate Short
Mounting Screw
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
Figure 5
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the
backplate of Fixture Body (C)
over the outlet box. Align the
holes in the backplate with the
mounting screws or alternate
short mounting screws. Place
caulk (not supplied) into the previously
removed mounting balls and then
attach Fixture using the mounting
balls. Hand tighten until snug.
Mounting Ball
A
Backplate
C
Mounting Screw
or Alternate Short
Mounting Screw

2of2
2016 QuoizelInc.
STEP 6 - BulbInstall
A. Insert bulb into socket and screw
snugly into place.
Figure 6
Bulb (not
supplied)
Socket
How to Replace Glass Shade
A remove Fixture Hood .
B Unscrew Flat Head Screws on the Cage with Glass Shade, remove
Tabs and Glass Shade from the Cage.
Glass Shade with a new one and re
iously removed parts back onto fixture.
. Unlock Lock Balls and from the Cage
.
C. Replace the verse above steps
to reinstall prev
Figure 7
STEP 7 -Apply Silicone Sealer
A. Make sure exterior wall surface
and fixture backplate are free of
dirt before applying caulk. Using
exterior grade caulk, caulk over
top of backplate and down other
side. Do not caulk bottom of
fixture backplate to ensure
proper moisture drainage.
Your fixture is now assembled
and ready to use. Enjoy!
Exterior
Grade
Caulk
Backplate
Flat Head Screw
Lock Ball
Glass Shade
Cage
Tab
Figure 8
EVG8409EK
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
FINISH: EARTH BLACK
Fixture can only be
mounted in the
direction indicated
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
7”
4.5”
9.25”
8.5”
15”
11.25”
8.5”Sq.
6”Sq.
ReleasedDate:2016-08-15
Fixture Hood
Bolt