Quoizel GAR8406SS User manual

Package Contents
Warnings and Cautions
1of2
For Style GAR8406SS
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar
Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBaseBulb100WMaximum,MediumBaseVintageBulbisrecommended,bulbnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Fixture Body
x1 C
Installation Guide #IS-GAR8406SS
2019 QuoizelInc. ReleasedDate:2019-03-20
visit us on-line at www.quoizel.com
B
Alternate
Mounting screw
x2
D
Front/Back
Glass Panel
x2
E
Side Glass
Panel
x2
STEP 1 Install Glass Panels-
A. Install two Side Glass Panels (E) first.
And then install Front/Back Glass
Panels (D). Make sure smooth surface
of Glass Panels (D/E) are outside
during installation.
B. Insert the top edge of the Glass
Panels (D/E) into the slot in the side of
the Fixture Body (C). Secure the
Glass Panels (D/E) by folding tabs in
the bottom edge of the Fixture Body
(C) onto the bottom edge of the Glass
Panels (D/E).
Figure 1
C
E
D
Slot
Tab
STEP 2 -Installing the Crossbar Assembly
A. Attach the Crossbar Assembly (A) to the outlet box with the head
of the green ground screw facing you. Secure the Crossbar
Assembly (A) with outlet box screws (not included). Tighten until
snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Figure 2
Outlet Box Screws
(not included)
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
A
Backplate
Mounting Screw
or Alternate Short
Mounting Screw
Mounting Ball
C
STEP 3 Test Fit the Backplate to the
Crossbar Assembly
-
A. Remove the mounting balls from the
Crossbar Assembly (A). Place the
backplate and Fixture Body (C) onto the
Crossbar Assembly (A) and secure with
mounting balls. Note: The backplate and
Hex Nut and
Lock Washer
Fixture Body (C) should be snug against the wall and held tight with
the mounting balls. If it is not, adjust the length of the mounting
screws or alternate short mounting screws on the Crossbar
Assembly (A) by unscrewing the preassembled hex nut and lock
washer and then screwing the mounting screws or alternate short
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate and Fixture Body (C) is secure,
remove the mounting ball and Fixture Body (C).
Figure 3
A
Outside Surface is smooth,
Internal Surface is ribbed.

2of2
2019 QuoizelInc. ReleasedDate:2019-03-20
visit us on-line at www.quoizel.com
Figure 4
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 5 -Install the Fixture Body
A. Position the backplate and Fixture Body (C) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws or alternate short mounting screws. Secure the Fixture Body
by using the mounting balls and hand tighten the mounting balls
until snug.
Figure 5
STEP 6 Install Bulb and-Apply
Silicone Sealer
A. Insert the bulb onto the socket
and screw snugly into place.
B. Make sure the exterior wall
surface and fixture backplate
are free of dirt before applying
caulk. Using exterior grade
caulk, caulk over top of
backplate and down both
sides. Do not caulk the bottom
of the fixture backplate to
ensure proper moisture
drainage.
Your fixture is now assembled
and ready to use. Enjoy!
Exterior
Grade Caulk
Exterior
Grade Caulk
Backplate
Figure 6
GAR8406SS
FINISH: STAINLESS STEEL
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
Backplate
Mounting Ball
C
Hex Nut and
Lock Washer
A
Socket
Vintage Bulb
(recommended
but not included)
Fixture can
only be
mounted in
the direction
indicated
7” 5.75”
2.25”
5.5”
12”
4.5”