Quoizel SNNL8408K Mounting instructions

Package Contents
1of2
Assembly Instruction Sheet #IS-SNNL8408_R1
For Styles SNNL8408K and SNNL8408PN
A
Crossbar
Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
LED16W
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
BFixture Body
x1
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
A
STEP 2 Fit Backplate to
Crossbar Assembly
-
A.
on Fixture Body (B) to
the
Remove mounting balls from the
Crossbar Assembly (A). Fit the
backplate
Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate
should be snug against
the wall and the mounting balls.
If
on Fixture
Body (B)
not, adjust the length of the
mounting screw on the Crossbar
Assembly (A) by unscrewing the
preassembled hex nut and lock
washer and then screwing the
mounting screws in or out of the Figure 2
crossbar until the correct length is achieved. Once the backplate on
Fixture Body (B) is secure, remove the mounting ball and Fixture
Body (B) and proceed to Step 3.
Mounting
Screw
B
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
B
Mounting Ball
A
Backplate
Exterior
Grade
Caulk
Backplate
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 4
STEP 4 Install Fixture Body-
A. Position the backplate and
Fixture Body (B) onto the
Crossbar Assembly (A).
Place the holes in the
backplate over the mounting
screws. Secure the Fixture
Body by using the mounting
balls and hand tighten the
mounting balls until snug.
Figure 5
STEP 5 -Apply Silicone Sealer
A. Make sure exterior wall surface and
fixture backplate are free of dirt
before applying caulk. Using
exterior grade caulk, caulk over top
of backplate and down other side.
Do not caulk bottom of fixture
backplate to ensure proper moisture
drainage.
Your fixture is now assembled and
ready to use. Enjoy!
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
RevisedDate:2017-11-03

2of2
HOW TO REPLACE GLASS PANELS
Allen Screw
Glass Panel
Cage
A. Fixture Hood. Separate Quick
Connector and then remove Cage with Glass Panels from the
fixture.
B. Unscrew Screws from the Cage and remove LED Module and Heat
Sink, Glass Holders. Replace Glass Panels from the Cage and then
re-install Glass Holders, LED Module and Heat Sink . Secure with
removed Screws.
C. Connect Quick Connectors. Attach Cage with Glass Panels back
onto the Fixture Hood and secure with Allen Screws.
Unlock Allen Screws on the
Glass Holder
Fixture Hood
LED Module
and Heat Sink
Quick Connector
Screw
SNNL8408K
FINISH: MYSTIC BLACK
SNNL8408PN
FINISH: PALLADIAN BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
Fixture can
only be
mounted in
the direction
indicated
12.5”
6.5”
5”
9”
8”
4.5”
OUO ZEL
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
RevisedDate:2017-11-03