Quoizel TML9008K Mounting instructions

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone [phone]
Fax [phone]
www.quoizel.com
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape,
safetyglasses.
EstimatedAssemblyTime:30-45minutes
Preparation:Identify andinspect allparts beforebeginning installation.Check packagecontent listand diagrams
belowto besure allparts arepresent. Ifany partsare missingor damaged,do notattempt toassemble, install,or
operatethe fixture.Contact customerservice forreplacement parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-TML9008K
For Style TML9008K
BulbRecommended: (3) CandelabraBase 60WMaximum,Alternatebulb(3) 13WCFL
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. February2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
C
Fixture
Body
x1
A
Mounting
Screw
x3
BGlass Panel
x4
STEP 2 -Attach Glass to Fixture
Body
A. Attach Glass Panels (B) on the
Fixture Body (C).
Figure 2
C
B
STEP 4 -Attach Fixture Hood
A. Thread the Stem onto the
Coupling inside of Fixture Body
(C), hand tighten until sung.
B. Place the Fixture Hood and the
Waterproof Washer over the
Stem. Secure by threading the
Finial onto the Stem. Hand
tighten until snug.
Figure 4
G
Coupling
STEP 5 Drill Pilot Holes on
Post
-
A. Carefully fit the Post Fitter over
the end of the Post (not
supplied), making sure the
Post Fitter is fully seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference.
After marking hole locations,
remove fixture from post and
drill 1/16” pilot holes for
screws. Post
Post Fitter
Figure 5
STEP 3 Install Bulb-
A. This fixture uses candelabra bulb
with a candelabra screw base.
Maximum 60 watts.
B. Insert bulb and screw snugly into
place.
Figure 3
Bulb
Socket
STEP 1 Seperate the parts from
the fixture
-
A. Unscrew the Finial, remove the
Waterproof Washer, the Cap
and the Stem from the fixture
(C).
Figure 1
C
Finial
Cap
Waterproof
Washer
Stem
Finial
Cap
Waterproof
Washer
Stem

2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. February2014
TML9008K
PART NUMBER
G3839PA
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
CLEAR SEEDY GLASS PANEL
REQ.
4
NO.
1
FINISH: MYSTIC BLACK
(3)
(Not Supplied)
60W Candelabra
base bulbs
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 5
STEP 6 Attach Fixture Body to
Post
-
A. Coat the top 1” of the Post with
Clear Silicone Caulk (not
supplied) and position the Post
FitterontothePost.Besureto
seat it completely, aligning the
holes in the Fitter with the 1/16”
Pilot Holes drilled into the Post.
B. Secure the Fixture to Post with
(3) Mounting Screws.
Your fixture is now assembled
and ready to use. Enjoy!
Mounting
Hole
Post
Fitter
Mounting
Screw
Post
Figure 6
8.5” Sq.
18”
21.5”
1