Quoizel GLN8409IB User manual

INSTRUCTION SHEET IS-GLN8409
STYLE NUMBER: GLN8409IB,GLN8410IB
ISSUED 08-2010 REVISED 2013-08-30
PACKAGE CONTENTS
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
WARNING:
CAUTION:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
WARNINGS AND CAUTIONS
1 OF 4
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (1) 150W A21 Medium Base Bulb.
● Helpful Tools (not included): Wire strippers.
PART DESCRIPTION QUANTITY
A Crossbar 1 pc
1 pc
1 pc
2 pcs
2 pcs
2 pcs
2 pcs
Green Ground Screw
Mounting Screw
Small Hex Nut
Small Lock Washer
Mounting Ball
Lock Ball
Fixture Assembly
B
C
D
E
F
G
H
2 pcs
A
B
C
D
E
F
H
G

INSTALLATION INSTRUCTIONS STYLE NUMBER: GLN8409IB,GLN8410IB
2 OF 4
STEP 1:
a. Take apart the Cage with Shade from the Fixture Body
by unlocking the Mounting Balls.
b. Remove Paper Cards from the top of the Cage with
Shade and from the gaps between the Cage and the
Shade.
STEP 2:
a. Place the Bolts in the bottom of the Fixture Hood
through the holes on the top edge of the Cage with
Shade. Secure them by threading Lock Balls back onto
the Bolts. Hand-tighten until snug.
Fixture Body
Cage with Shade
Fixture Hood
Bolt
Lock Ball
Cage with Shade
Paper Card
Paper Card
Mounting Ball

INSTALLATION INSTRUCTIONS
3 OF 4
STEP 3:
a. Screw the Mounting Screws into the Crossbar place
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as
shown Secure the position of the Mounting Screws by
tightening the Hex Nuts against the Crossbar
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws
,
.
.
.
Outlet Box
Crossbar
Mounting Screw
Hex Nut
Outlet Box Screw
Lock Washer
WHITE WIRE
BLACK (OR RED) WIRE
GROUND WIRE
WHITE WIRE
BLACK WIRE
GROUND WIRE
FROM HOUSE
FROM HOUSE
FROM HOUSE
FROM FIXTURE
FROM FIXTURE
FROM FIXTURE
STEP 4:
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White Wire to the Fixture Supply
Wire (White Wire).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black Wire).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
Use Wire Connectors (not supplied) to connect the
wires.
STEP 5:
a. Place the Backplate over the Mounting Screws and
secure with the Mounting Balls. Hand-tighten until
snug.
Mounting Screw
Backplate
Outlet Box Mounting Ball
STEP 6:
a. Install the correct Bulb referring to fixture markings and/or labels for maximum wattage.
STYLE NUMBER: GLN8409IB,GLN8410IB

INSTALLATION INSTRUCTIONS
4 OF 4
EXTERIOR GRADE
CAULK
MOUNTING BALL
STEP 7:
a. Refer to the following information for caulking instructions:
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation instructions,
proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking. Using
EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were the FIXTURE
BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of backplate and down
other side. to ensure proper moisture drainage.DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE
For assemble the MOUNTING BALLS, please note that
you are required to apply a small amount of Silicone
sealer to the threaded side of the MOUNTING BALLS
and then install them onto the MOUNTING SCREWS.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
EXTERIOR WALL SURFACE
STYLE NUMBER: GLN8409IB,GLN8410IB