Quoizel Everglade EVG9011EK Mounting instructions

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2016 QuoizelInc.
Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A21MediumBasebulb150WMaximum.
www.quoizel.com Care + Maintenance
LightSource:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
EstimatedAssembly Time:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
AMounting Screw
x3
Fixture
Body
x1
Assembly Instruction Sheet #IS-EVG9011EK
For Style EVG9011EK
BFixture Hood
x1
C
ReleasedDate:2017-08-11
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
DLock Ball
x2
STEP 1 Install Bulb and
Fixture Hood
-
A. Insert bulb into socket and
screw snugly into place
B. Place the bolts on the
bottom edge of the Fixture
Hood (B) through the holes
on the top edge of the
Fixture Body (C) and secure
with Lock Balls (D). Hand
tighten until sung.
Figure 1
STEP 2 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the end of the
Post (not supplied), making sure the Post
Fitter is fully seated.
B. Mark the drill point for the (3) Mounting
Screws, using (3) Mounting Holes as
reference. After marking hole locations,
remove fixture from post and drill 1/16” pilot
holes for screws.
Post
Post Fitter
Figure 2 Mounting Hole
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture Figure 3
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined
together. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
STEP 4 Attach Fixture Body to Post-
A. Coat the top 1” of the Post with Clear
Silicone Caulk (not supplied) and
position the Post Fitter onto the Post. Be
sure to seat it completely, aligning the
holes in the Fitter with the 1/16” Pilot
Holes drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
Post
Post Fitter
Figure 4
Mounting Hole A
B
C
D
Bulb (not
supplied)
Socket

2of2
2016 QuoizelInc.
EVG9011EK
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
ReleasedDate:2017-08-11
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
FINISH: EARTH BLACK
How to Replace Glass Shade
A remove Fixture Hood .
B Unscrew Flat Head Screws on the Cage with Glass Shade, remove
Tabs and from the Cage.
Glass Shade with a new one and re
iously removed parts back onto fixture.
. Unlock Lock Balls and from the Cage
.
C. Replace the verse above steps
to reinstall prev
Glass Shade
Flat Head
Screw
Lock Ball
Glass
Shade
Cage
Tab
Figure 5
Fixture
Hood
20.25”13.5”
10.5”
7.25”
7.25”
10.5”
Bolt