Package Contents
Warnings and Cautions
1of2
For Style WWD8407IB
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar
Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBasebulb100WMaximum,bulbnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Fixture Body
x1 B
Figure 1
STEP 1 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
STEP 2 Test Fit the
Backplate to the Crossbar
Assembly
-
A. Remove the mounting balls
from the Crossbar
Assembly (A). Place the
backplate and Fixture Body
(B) onto the Crossbar
Assembly (A) and secure
with mounting balls. Note:
The backplate and Fixture
Body (B) should be snug
against the wall and held
tight with the mounting
balls. If it is not, adjust the
length of the mounting
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
Mounting Screw
B
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
(Step 2 Continued)
screws on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate and Fixture Body (B) is secure,
remove the mounting ball and Fixture Body (B) and proceed to
Step 3.
STEP 4 -Install the Fixture
Body
A. Position the backplate and
Fixture Body (B) onto the
Crossbar Assembly (A).
Place the holes in the
backplate over the
mounting screws. Secure
the Fixture Body by using
the mounting balls and
hand tighten the mounting
balls until snug.
Mounting
Ball
A
Backplate
Figure 4
Mounting Screw
B
Installation Guide #IS-WWD8407IB
2018 QuoizelInc. ReleasedDate:2018-04-04
visit us on-line at www.quoizel.com
