Quoizel WKF9011EK Mounting instructions

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2017 QuoizelInc.
Assembly Instruction Sheet #IS-WKF9011EK
For Style WKF9011EK
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Package Contents
AMounting Screw
x3
D
Fixture Body
x1
Glass Panel
x4
B
Fixture Hood
x1
C
STEP 1 Install Glass Panels,
Bulbs and Fixture Hood
-
A. Unscrew screws from the top
edge of the Fixture Body (D) to
remove glass holder.
B. Insert Glass Panels (C) into the
slot in the bottom edge of the
Fixture Body (D). Attach the glass
holder onto the top edge of Glass
Panels (C) and align holes on it to
mounting holes on the Fixture
Body (D). Secure the glass holder
with removed screws. Tighten
gently until snug with
screwdrivers.
C. Insert bulbs onto sockets and
screw snugly into place.
D. Remove lock screws from the
Figure 1
ReleasedDate:2017-09-29
STEP 2 -Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter Marking Pen
Mounting
Hole
Post
Lighting
Post
Post
Fixture
Fitter
Figure 2
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)B10CandelabraBasebulbs60WMaximumor
(3)CandelabraBaseT8Vintage bulbs are recommended but not supplied.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Screw
Glass
Holder
B
C
D
Label “A”
Label “A”
Lock
Screw
T8 Vintage Bulb
(recommended
but not supplied)
Socket
Slot
(Step 1 Continued)
bottom edge of the Fixture Hood (B).
E. Align the label “A” on the top edge of the Fixture Body (D) to the
label “A” in the bottom edge of the Fixture Hood (B). Attach the
Fixture Hood (B) to the top edge of the Fixture Body (D) and secure
with removed lock screws. Hand tighten until snug with
screwdrivers.
STEP 3 M C
EM H
-arking the enter of
ach ounting ole
A. Remove the light fixture. Using
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
Center Punch
Hammer
Marking
Post
Figure 3

2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
STEP 6 Attach the fixture to the Post Mount-
A. Place the fixture on the post lining up the mounting holes on the
fixture fitter with the holes on the post. Use the Mounting Screws (A)
to attach the fixture to the post.
Your fixture is now assembled and ready to use. Enjoy!
Post
Hole
Fixture Fitter Mounting Hole
Post Lighting
A
Figure 5
Figure 6
WKF9011EK
FINISH: EARTH BLACK
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
2017 QuoizelInc. ReleasedDate:2017-09-29
STEP 4 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 5 above.
1/16” bit and drill
Post
Figure 4
19.25”
10.75” SQ.