Quoizel GDM8406PN User manual

Package Contents
Warnings and Cautions
1of2
For Style GDM8406PN
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar
Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBasebulb100WMaximum,bulbnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
MissingParts?Contactyouroriginalplaceof
purchase.
CFixture Body
x1
BHandle
x1
2018 QuoizelInc. ReleasedDate:2018-04-04
visit us on-line at www.quoizel.com
Installation Guide #IS-GDM8406PN
STEP 1 Install Handle-
A. Remove Styrofoam inside of the cage.
B. Remove lock screws from the Fixture Body (C).
C. Attach the Handle (B) to the Fixture Body (C) and secure by
threading lock screws back into mounting holes on the Fixture
Body (C). Hand tighten until snug.
Figure 1 C
Mounting Hole
B
Styrofoam
(Remove)
Lock Screw
STEP 2 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
STEP 3 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws in or
out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (C) is secure, remove the mounting ball
and Fixture Body (C) and proceed to Step 4.
Figure 2
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 3
Mounting Screw
C

2of2
GDM8406PN
FINISH: PALLADIAN BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
Fixture can
only be
mounted in
the direction
indicated
4.75" Dia.
6.25”
13"
5.5” SQ.
3.75"
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 4
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wires
from Fixture
Socket
Bulb (not
included)
Exterior
Grade Caulk
Backplate
Exterior
Grade
Caulk
STEP 6 -Install the Bulb and
Apply Silicone Sealer
A. Insert the bulb onto socket
and screw snugly into place.
B. Make sure the exterior wall
surface and fixture backplate
are free of dirt before applying
caulk. Using exterior grade
caulk, caulk over top of
backplate and down both
sides. Do not caulk the bottom
of the fixture backplate to
ensure proper moisture
drainage.
Your fixture is now assembled
and ready to use. Enjoy!
STEP 5 -Install the Fixture Body
A. Position the backplate and Fixture Body (C) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws. Secure the Fixture Body by using the mounting balls and
hand tighten the mounting balls until snug.
Figure 5
Figure 6
Mounting
Ball
A
Backplate
Mounting Screw
C
2018 QuoizelInc. ReleasedDate:2018-04-04
visit us on-line at www.quoizel.com
HOW TO REPLACE GLASS PANEL
A. Unscrew screws on the bottom corners of the cage and remove the
glass panel holder from the cage.
B. Replace glass panel carefully and secure with previously removed
glass panel holder and screws. Tighten screws until snug with
screwdrivers.
Screw
Glass Panel
Holder
Glass Panel
Cage