Quoizel VVSP9348BN User manual

Pleasegoto forproductcleaningtips.Gotothe selection.
Integrated7WLED 15-20minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver.
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-VVSP9348
For Styles VVSP9348BN, WTVVSP9348
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Figure 1
APlug
x1
BWrench
x1
C
D
E
F
Socket
Assembly
x1
Threaded
Rod
x1
Rod
x1
Base
x1
B
A
C
D
E
F
Adjustment
Button
STEP 1 Install Rods and Socket
Assembly
-
A. Thread the SocketAssembly (C) and the
Rods (D/E) to the Base (F) together as
shown. Hand tighten until snug. Note: If the
shade and the base are not lined up after
assembly, unscrew the hex nut on the
bottom of the base with the wrench (B),
adjust the rods until the shade and the base
are lined up.And then secure the rods to
the base. Hand tighten until snug with the
Wrench (B).
B.Adjust the SupportArm and the Shade
to proper location by adjust the
Ajustment Buttons.
C. Insert the Plug (A) into the cord from
the Base (F) as shown.
Your fixture is now assembled and
ready to use. Enjoy!
Replace LED Lamp
If the LED module would fail to work it is replaceable. Please order
the replacement module from Quoizel's' Customer Service and
follow these instructions to remove and replace the LED module.
A.
Unscrew the screw on the center of and remove the
reflector. Squeeze the two wings together, hold onto the bottom half
of quick connector, pull the top half of quick connector from the
bottom half.
To reconnect, support the bottom half while inserting the top
half aligned correctly and pushing in until the wings grab hold
and the top half cannot be pulled back out.
Unscrew the lock screws from the shade and remove the diffuser
from the shade.
B. Unscrew the screws on the LED Lamps and remove the LED lamp.
C. reflector
D.
E. Place the diffuser back onto the shade and secure with the removed
screws. Hand tighten until snug.
2015 QuoizelInc. December2015
Rev.A

2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
VVSP9348BN/VVSP9348WT
PARTNUMBER
NOTE: ALLDIMENSIONSARE ROUNDED UP TO THE NEAREST 1/4"
REPLACEMENTPARTDESCRIPTION QTY.
NO.
1
FINISH:BRUSHEDNICKEL/WESTERNBRONZE
21”
47.5”
11” Dia.
I1009MD LED MODULE 1
1
2015 QuoizelInc. December2015
Rev.A
2
K813BL LED DRIVER W/CORD 24V-0.2ARIGHTANGLE 1
2