R-Can Sterilight SC1 Installation and operating instructions
Owner’s Manual
Installation, Operation and Maintenance
SC1, SC2.5, SC4,
SC1/2, SC2.5/2, SC4/2
425 Clair Road West P.O. Box 1719
Guelph, ON N1L 1R1 Canada
t. 519 763 1032 f. 519 763 5069
Manufactured in Canada by:
EPA# 57987-CN-001
January 2008
P/N 520074
Why buy original factory specified lamps ...
Why are Sterilume®lamps the best available ...
Recycle ...
®systems are third-party verified in actual biodosimetry tests (complete
®®lamps. The use of any
®
the CSA
WILL NOT warranty ANY
®replacement lamps are used in the system. The use of any lamp, unless
specifically authorized by the company, will result in a full voidance of the warranty -
®UV lamps.
NEW Environmentally Friendly
®lamps are TCLP*
LongLife+™
life and increased efficiency.
construction and date and colour coded for easy identification.
®UV lamps.
* Note:
Government and most states to determine whether or not spent
fluorescent lamps should be characterized as hazardous waste.
to www.lamprecycle.org
Table of Contents:
1
2
Water Chemistry 3
4-5
6-7
8
9
10-11
Symbols:
Caution Protective
Ground
Electrical
Warning Fragile
Eye Protection AC Current
1
Parts:
Hard glass, coated Sterilume®-EX UV
lamps for long, consistent life
(9000 hours)
214 fused domed quartz sleeves
with fire polished ends
aluminum gland nut RN-001
304 stainless steel reactors with 600
grit polish (A249 pressure rated tube)
1/2” MNPT / 3/8” FNPT
combination ports for application
flexibility
Axial flow reactor design for increased
hydraulic efficiency
o-ring OR-212
retaining clip
2 meters (6.5‘)
power cord
integral ballast and lamp
connector with green LED
lamp/power indicator
ground wire
260120
NEW
mounting brackets - ROC-CC
2
Safety Instructions:
Note: The UV lamp inside of the disinfection system is rated at an effective life of
approximately 9000 hours. To ensure continuous protection, replace the UV lamp
annually.
WARNING
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. CAUTION
3. DANGER
since water is present near electrical equipment. Unless a situation is
encountered that is explicitly addressed by the provided maintenance
authorized service facility.
4. Carefully examine the disinfection system after installation. It should not
7. Do not use this disinfection system for other than intended use (potable
the manufacturer / distributor may cause an unsafe condition.
8. Intended for indoor use only. Do not install this disinfection system where
not store this disinfection system where it will be exposed to the weather.
Do not store this disinfection system where it will be exposed to
the water supply has been disconnected.
disinfection system.
used. A cord rated for less Amperes or Watts than the disinfection system
Warning:
unit first. Never operate the UV system while the UV lamp is outside of the
UV chamber.
3
Water Chemistry:
Water quality is extremely important for the optimum performance of your UV
• Iron: < 0.3 ppm (0.3 mg/L)
• Hardness*: < 7 gpg (120 mg/L)
• Turbidity: < 1 NTU
• Manganese: < 0.05 ppm (0.05 mg/L)
• Tannins: < 0.1 ppm (0.1 mg/L)
• UV Transmittance: > 75% (call factory for recommendations on
applications where UVT < 75%)
efficiently provided the quartz sleeve is cleaned periodically. If total hardness
If your water chemistry contains levels in excess of those mentioned above, proper
pre-treatment is recommended to correct these water problems prior to the
installation of your UV disinfection system. These water quality parameters can be
tested by your local dealer, or by most private analytical laboratories. Proper
pre-treatment is essential for the UV disinfection system to operate as intended.
4
Installing your UV Disinfection System:
destroy any residual contamination.
fault interrupt circuit.
disinfection system where it may be exposed to the weather.
lines.
disinfection system should be the last treatment the water receives before it
reaches the faucet.
coppercopper
5
the disinfection system to the wall with the supplied clamp. If required, a
double-end clamp can be purchased from your dealer to affix to an RO
membrane.
3. Various connection methods can be used to connect the water source to
the disinfection system, however union type connectors are recommended. In
may have entered the distribution system while on by-pass.
DO NOT SOLDER CONNECTIONS WHILE ATTACHED TO THE
DISINFECTION SYSTEM AS THIS COULD DAMAGE THE
O-RING SEALS.
6. The power source provided with your disinfection system must be located
DO NOT USE AN OUTLET THAT CAN
BE SWITCHED OFF (IE. A WASTE DISPOSAL OUTLET). Attach the lamp
into the outlet and ensure the POWER-ON LED is illuminated.
Note:
unit. In addition, to clear any air or debris from the system, open the faucet and
6
Operating & Maintenance Instructions:
Caution: prior to performing any work on the
disinfection system, always disconnect the power
supply rst.
UV Lamp Replacement / Cleaning:
1. To replace the lamp, there is NO need to disconnect the
system from the water supply, nor to drain the water from
must be replaced after 9,000 hours of continuous
adequate disinfection.
2. Disconnect main power source and allow the unit to
connector. Remove connector and lamp from the reactor
is removed from the chamber. If the lamp is removed on
3. To install a new lamp, first remove the lamp from its
installation in one position. Ensure the connector is fully
4. Once the lamp is fully seated on the connector, slide the
from the body of the connector in order that the
the reactor chamber.
Figure 1
Figure 2
Figure 3
Figure 4
7
Quartz Sleeve Replacement / Cleaning:
1. If the water contains any hardness minerals
the quartz sleeve will require periodic
remove the UV lamp as outlined in step 1-4
Caution: prior to performing any work on the
disinfection system, always disconnect the power
supply rst.
sleeve at the opposite end to the lamp connection
annually. Remove quartz sleeve carefully from chamber.
sleeve before it is reinstalled in the reactor (be sure not
instructions.
illuminated.
Note: If the system is put on a temporary by-pass or if
it becomes contaminated after the disinfection system,
it will be necessary to shock the system with household
bleach for a full 20 minutes before resuming the use of
the water.
Figure 6
Figure 7
Figure 8
Figure 5
8
Fluence Dose Curves:
SC1 & SC1/2
SC2.5 & SC2.5/2
SC4 & SC4/2
9
Manufacture’s Warranty:
Manufacturer warrants the ultraviolet disinfection system hardware and electrical
basis. Manufacturer warrants the ultraviolet lamps to be free from defects in material
Conditions, Exceptions, and Exclusions
The foregoing limited Warranty is subject to the following terms and conditions:
a) Iron: < 0.3 ppm (0.3 mg/L)
b) Hardness*: < 7 gpg (120 mg/L)
c) Turbidity: < 1 NTU
d) Manganese: < 0.05 ppm (0.05 mg/L)
e) Tannins: < 0.1 ppm (0.1 mg/L)
f) UV Transmittance: > 75% (call factory for recommendations on
applications where UVT < 75%)
efficiently provided the quartz sleeve is cleaned periodically. If total
are not present.
2. This limited Warranty shall not apply to any unit which has been repaired or
altered by anyone other than the Warrantor or by a person authorized by the
accident.
10
Specifications:
MODEL SC1 SC2.5 SC4
Flow Rate1
US Public Health
16mJ/cm2
(0.45 m3
(0.95 m3
(1.70 m3
R-Can Standard
30 mJ/cm2
(0.24 m3
(0.57 m3
(0.91 m3
NSF/EPA
40mJ/cm2
(0.12 m3
(0.43 m3
(0.64 m3
Dimensions
Length
Cell Diameter
Inlet/Outlet Port Size combo
combo
combo
Shipping Weight
Electrical
Voltage 100-130V/50-60Hz 100-130V/50-60Hz 100-130V/50-60Hz
Power
Consumption 12 W 16 W 19 W
Lamp Watts 10 W 14 W 17 W
Maximum Operating
Pressure
Ambient Water
Temperature
Lamp Type “GREEN”
Visual “Power-On”
Visual Lamp
Chamber Material
1. Flow rates based on UVT10=95%
NEW
System Specifications
11
Specifications:
MODEL SC1/2 SC2.5/2 SC4/2
Flow Rate1
US Public Health
16mJ/cm2
(0.45 m3
(0.95 m3
(1.70 m3
R-Can Standard
30 mJ/cm2
(0.24 m3
(0.57 m3
(0.91 m3
NSF/EPA
40mJ/cm2
(0.12 m3
(0.43 m3
(0.64 m3
Dimensions
Length
Cell Diameter
Inlet/Outlet Port Size combo
combo
combo
Shipping Weight
Electrical
Voltage 200-250V/50-60Hz 200-250V/50-60Hz 200-250V/50-60Hz
Power
Consumption 12 W 16 W 19 W
Lamp Watts 10 W 14 W 17 W
Maximum Operating
Pressure
Ambient Water
Temperature
Lamp Type “GREEN”
Visual “Power-On”
Visual Lamp
Chamber Material
1. Flow rates based on UVT10=95%
System Specifications
NEW
This manual suits for next models
5
Table of contents
Other R-Can Water Filtration System manuals
Popular Water Filtration System manuals by other brands
3M
3M TFS450 owner's manual
Thermal Care
Thermal Care SF Series Installation, operation and maintenance manual
Wilo
Wilo Voda Air Installation and operating instructions
Atlas Filtri
Atlas Filtri NEUTRAL MINI Installation, use and maintenance manual
Axiall
Axiall Accu-Tab 100 Series Installation and operating instructions
Spectra Watermakers
Spectra Watermakers NEWPORT 400 Mk II Installation & owner's manual
Bayhall
Bayhall FM2KTOSC Installation and operating instructions
Pentek
Pentek PBH-410 Installation and operating instructions
NSF
NSF RinseWell Smart Eco Rinse 4000 Series User manual and installation guide
Hoshizaki
Hoshizaki ROX-20TB2-U installation manual
Krohn-Hite
Krohn-Hite 3940 Operating and maintenance manual
Netafim
Netafim SCREENGUARD Installation and user manual