RAB FFLED39 User manual

FFLED INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is
required for safety. For xtures weighing more than 10 lbs - Do not mount to an outlet cover unless a separate splice box is used.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
ARM MOUNTING
1. Seal arm thread using teon tape or silicone sealant.
2. Secure the LED Flood to a 1/2” NPS hole in a junction box
or landscape post. Heavy duty XC1 cover provided.
3. Plug all unused holes and seal threads with silicone.
4. The swivel arm on the LED Flood allows 180º of vertical
aiming adjustment depending on mounting location.
SLIPFITTER MOUNTING
1. The sliptter mounting ts a 2 3/8” O.D. Tenon. Place the
sliptter over the Tenon and secure the xture with the
two Set Screws on the side of the sliptter.
2. Remove two screws and plug on side of Round Cover
Plate. Remove the Round Cover Plate and adjust the
angle of the xture.
3. Loosen the Locking Bolt and swivel xture to desired
angle.
4. Tighten the Locking Bolt and re-attach Round Cover
Plate.
TRUNNION MOUNTING
CAUTION: UL and C-UL listed or CSA certied liquid tight
cord grip suitable for use with three conductor type
STW exible cord shall be used for connection to a wet
location outlet box provided by others.
To adjust the angle of the xture using the trunnion:
1. Loosen the Pivot Bolts & angle locking screw.
2. Adjust xture to desired angle.
3. Tighten Pivot Bolts & angle locking screw.
Locking
Bolt
Tenon
Set Screws
Round
Cover
Plate
Pivot Bolts
FFLED Arm FFLED Trunnion
FFLED Sliptter
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough
to touch. Do not clean or maintain while xture is
energized.
1. Clean glass lens with non-abrasive glass cleaning
solution.
2. Do not open the xture to clean the LED. Do not touch
the LED.
TROUBLESHOOTING
1. Check that the line voltage at the xture is correct. Refer
to wiring directions.
2. Is the xture grounded properly?
3. Is the photocell, if used, functioning properly?

FFLED INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
Patent - US: Pat D643,147
ACCESSORIES AND REPLACEMENT
PARTS
Chrome Wire Guard: GDFFLED39W
Poly Shield: GDFFLED39P
Lens & Door Replacement: LFFLED39 (bronze)
LFFLED39W (white)
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
FFLED263952 IN 0315
GUARD OR SHIELD INSTALLATION
Wire Guard and Poly Shield mount with (4) #8-32 Stainless
Steel Screws. Screws are provided with accessory. Guard
and Shield may be used together. See gure 1 for Guard. See
gure 2 for Shield
1. Line up guard with pre-existing, pre-drilled holes in
frame as shown, tighten screws.
Stainless Steel
Screws (4)
Figure 1
Figure 2
Stainless Steel
Screws (4)
ONOFF WIRING
Universal voltage driver permits operation at 120V to 277VAC,
50 or 60Hz, except xtures factory ordered with a 120V
photocell (/PC), 120V swivel photocell (/PCS), 277V photocell
(/PC2) and 277V swivel photocell (/PCS2). Units ordered with
(/480V) sux are 480V. For Non-Dimming, follow the wiring
directions as in g. 1.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the bare copper Ground wire from xture to
supply ground.
LIGHT
FIXTURE
(+)LINE BLACK
(-)COMMON WHITE
GROUND GROUND
Fig. 1
010V DIMMABLE WIRING
Universal voltage driver permits operation at 120V thru 277V,
50 or 60 Hz. For 0-10V Dimming, follow the wiring directions
as in g. 2.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply ground.
Do NOT connect the GROUND of the dimming xture to
the output.
4. Connect the purple xture lead to the (V+) DIM lead.
5. Connect the gray xture lead to the (V-) DIM lead.
6. Cap the yellow xture lead, if present. Do NOT connect.