RAB SLIM 57 User manual

SLIM 57 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FIXTURE MOUNTING
To ensure weatherproof seal, apply weatherproof silicone
sealant around the edge of the Housing and/or Junction
Box. This is especially important with an uneven wall
surface. Silicone all plugs and unused conduit entries.
1. Loosen Door Screws and open the Door. Screws will
remain in place.
2. Tether Cable provided for hands free wiring.
3. Knock out appropriate Slots when mounting to junction
box (not supplied) or lag bolt to mounting surface using
locations noted below. Use Leveling Bubble to level
xture.
4. Feed supply wires through Junction Box(not supplied).
Check that the Gasket is fully sealed.
5. Make sure Housing Gasket is properly seated. Close and
tighten the Door Screws. Silicone all Plugs and unused
conduit entries.
6. If outdoor surface is irregular, use caulk to seal any gaps
around the Housing.
Housing
Gasket
Junction Box
(not supplied)
Door
Knock Out Slots
Door Screws (2)
Plug
Leveling Bubble
Gasket
Lag Bolt
Locations
Drilling
Template
Housing
13 1/4”
9 5/8”
4 13/16”
5 5/8”8 5/16”
WIRING
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz, except xtures factory ordered with a
120V photocell (/PC) and 277V photocell (/PC2) and xtures
factory ordered with a 120V swivel photocell (/PCS) or 277V
swivel photocell (/PCS2) or 480V swivel photocell (/PCS4).
Units ordered with (/480V) sux are 480V.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply
ground.
Tether Cable

SLIM 37 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FIXTURE MOUNTING
To ensure weatherproof seal, apply weatherproof silicone
sealant around the edge of the Housing and/or Junction
Box. This is especially important with an uneven wall
surface. Silicone all plugs and unused conduit entries.
1. Loosen Door Screws and open the Door. Screws will
remain in place.
2. Tether Cable provided for hands free wiring.
3. Knock out appropriate Slots when mounting to junction
box (not supplied) or lag bolt to mounting surface using
locations noted below. Use Leveling Bubble to level
xture.
4. Feed supply wires through Junction Box (not
supplied). Check that the Gasket is fully sealed.
5. Make sure Housing Gasket is properly seated. Close and
tighten the Door Screws. Silicone all Plugs and unused
conduit entries.
6. If outdoor surface is irregular, use caulk to seal any gaps
around the Housing.
Housing
Gasket
Junction Box
(not supplied)
Door
Knock Out Slots
Door Screws (2)
Plug
Leveling Bubble
Gasket
Lag Bolt
Locations
Drilling
Template
5 5/8”
5 5/8”
1 1/4”
1 1/4”
8 1/8”
8 1/8”
Housing
WIRING
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz, except xtures factory ordered with a
120V photocell (/PC) and 277V photocell (/PC2) and xtures
factory ordered with a 120V swivel photocell (/PCS) or 277V
swivel photocell (/PCS2) or 480V swivel photocell (/PCS4).
Units ordered with (/480V) sux are 480V.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply
ground.
Tether Cable

SLIM 37 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
SLIM35 POLYSHIELD
RAB LIGHTING
3/22/2013
SLIM35 WIRE GAURD
RAB LIGHTING
3/22/2013
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens & xture with non-abrasive glass cleaning
solution.
2. Do not open xture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Is the xture grounded properly?
3. Be sure the photocell, if used, is functioning properly.
GUARD/ SHIELD INSTALLATION
1. Remove left and right Cover Plates as in gure 1 and
discard.
2. Mount wire guard and/ or poly shield with (4) #8-32 x 1/2”
Stainless Steel Screws. Screws are provided with the
accessory.
Stainless Steel Screws (4)
FULL CUTOFF/ GUARD/ SHIELD
INSTALLATION
1. Remove (4) Stainless Steel Screws from the Full Cuto
Hood.
2. Mount wire guard and/ or poly shield over the full cuto
hood with (4) #8-32 x 1/2” Stainless Steel Screws as shown
in gure 2. Screws are provided with the accessory.
Stainless Steel
Screws
Figure 1
Stainless Steel
Screws
Figure 2
Cover Plate
Full Cuto Hood
Note: Guard and shield may be used together.
Note: Guard, shield and full cuto hood may be used together
with (4) #8-32 x 3/4” stainless steel screws (supplied by others).
Stainless Steel Screws (4)
PHOTOCELL INSTALLATION
Photocell may be installed in the eld. Apply weatherproof
silicone sealant to all plugs and unused conduit entries.
1. Remove close up plug on top of the wall mounting box.
2. Install photocell and wire as per diagram.
3. Use photocell rated for your supply voltage.
“COM”
PHOTOCELL
WP2FC
LIGHT
FIXTURE
BLACK
WHITE
PHOTOCELL

SLIM 37 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
SLIM37 Cool SLIM37 Neutral SLIM37 Warm
SLIM37-IN 0615
SLIMFC37 Cool SLIMFC37 Neutral SLIMFC37 Warm
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com

SLIM 57 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
SLIM47 POLYSHIELD
RAB LIGHTING
3/22/2013
SLIM47 WIRE GAURD
RAB LIGHTING
3/22/2013
Stainless Steel
Screws (4)
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens & xture with non-abrasive glass cleaning
solution.
2. Do not open xture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Is the xture grounded properly?
3. Be sure the photocell, if used, is functioning properly.
GUARD/ SHIELD INSTALLATION
1. Remove left and right Cover Plates as in gure 1 and
discard.
2. Mount wire guard and/ or poly shield with (4) #8-32 x 1/2”
Stainless Steel Screws. Screws are provided with the
accessory.
Stainless Steel Screws (4)
FULL CUTOFF/ GUARD/ SHIELD
INSTALLATION
1. Remove (4) Stainless Steel Screws from the Full Cuto
Hood.
2. Mount wire guard and/ or poly shield over the full cuto
hood with (4) #8-32 x 1/2” Stainless Steel Screws as shown
in gure 2. Screws are provided with the accessory.
Stainless Steel
Screws
Figure 1
Stainless Steel
Screws
Figure 2
Cover Plate
Full Cuto Hood
Note: Guard and shield may be used together.
Note: Guard, shield and full cuto hood may be used together
with (4) #8-32 x 3/4” stainless steel screws (supplied by others).
Stainless Steel Screws (4)
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
PHOTOCELL INSTALLATION
Photocell may be installed in the eld. Apply weatherproof
silicone sealant to all plugs and unused conduit entries.
1. Remove close up plug on top of the wall mounting box.
2. Install photocell and wire as per diagram.
3. Use photocell rated for your supply voltage.
“COM”
PHOTOCELL
WP2FC
LIGHT
FIXTURE
BLACK
WHITE
PHOTOCELL

SLIM 57 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
SLIM57 Cool SLIM57 Neutral SLIM57 Warm
SLIM57-IN 0615
SLIMFC57 Cool SLIMFC57 Neutral SLIMFC57 Warm
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com

SLIM 62 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FIXTURE MOUNTING
To ensure weatherproof seal, apply weatherproof silicone
sealant around the edge of the Housing and/or Junction
Box. This is especially important with an uneven wall
surface. Silicone all plugs and unused conduit entries.
1. Loosen Door Screws and open the Door. Screws will
remain in place.
2. Tether Cable provided for hands free wiring.
3. Knock out appropriate Slots when mounting to junction
box (not supplied) or lag bolt to mounting surface using
locations noted below. Use Leveling Bubble to level
xture.
4. Feed supply wires through Junction Box (not
supplied). Check that the Gasket is fully sealed.
5. Make sure Housing Gasket is properly seated. Close and
tighten the Door Screws. Silicone all Plugs and unused
conduit entries.
6. If outdoor surface is irregular, use caulk to seal any gaps
around the Housing.
Housing
Gasket
Junction Box
(not supplied)
Door
Knock Out Slots
Door Screws (2)
Plug
Leveling Bubble
Gasket
Lag Bolt
Locations
Drilling
Template
Housing
13”
6 1/2”
1 5/8”
1 1/2”
5 3/8”
1 1/2”
8 1/4”
WIRING
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz. except xtures factory ordered with a
120V photocell (/PC) and 277V photocell (/PC2) and xtures
factory ordered with a 120V swivel photocell (/PCS) or 277V
swivel photocell (/PCS2) or 480V swivel photocell (/PCS4).
Units ordered with (/480V) sux are 480V.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply
ground.
Tether Cable

SLIM 62 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
SLIM56 WIRE GAURD
RAB LIGHTING
3/22/2013
SLIM56 POLYSHIELD
RAB LIGHTING
3/22/2013
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens & xture with non-abrasive glass cleaning
solution.
2. Do not open xture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Is the xture grounded properly?
3. Be sure the photocell, if used, is functioning properly.
GUARD/ SHIELD INSTALLATION
1. Remove left and right Cover Plates as in gure 1 and
discard.
2. Mount wire guard and/ or poly shield with (4) #8-32 x 1/2”
Stainless Steel Screws. Screws are provided with the
accessory.
Stainless Steel Screws (4)
FULL CUTOFF/ GUARD/ SHIELD
INSTALLATION
1. Remove (4) Stainless Steel Screws from the Full Cuto
Hood.
2. Mount wire guard and/ or poly shield over the full cuto
hood with (4) #8-32 x 1/2” Stainless Steel Screws as shown
in gure 2. Screws are provided with the accessory.
Stainless Steel
Screws
Figure 1
Stainless Steel
Screws
Figure 2
Cover Plate
Full Cuto Hood
Note: Guard and shield may be used together.
Note: Guard, shield and full cuto hood may be used together
with (4) #8-32 x 3/4” stainless steel screws (supplied by others).
Stainless Steel Screws (4)
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
PHOTOCELL INSTALLATION
Photocell may be installed in the eld. Apply weatherproof
silicone sealant to all plugs and unused conduit entries.
1. Remove close up plug on top of the wall mounting box.
2. Install photocell and wire as per diagram.
3. Use photocell rated for your supply voltage.
“COM”
PHOTOCELL
WP2FC
LIGHT
FIXTURE
BLACK
WHITE
PHOTOCELL

SLIM 62 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TM
SLIM62 Cool SLIM62 Neutral SLIM62 Warm
SLIM62-IN 0615
SLIMFC62 Cool SLIMFC62 Neutral SLIMFC62 Warm
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
This manual suits for next models
2
Table of contents
Other RAB Light Fixture manuals
Popular Light Fixture manuals by other brands

Christie
Christie High Performance Xenon Lamp CDXL product manual

Lithonia Lighting
Lithonia Lighting Shoplight installation instructions

EuroLite
EuroLite SMD PRO 540 user manual

Chauvet
Chauvet Legend 412Z user manual

Lightmaxx
Lightmaxx VEGA ZOOM Wash Beam user manual

ENS
ENS UV-SM installation instructions