RAB LFLED 4LV User manual

INSTRUCTIONS
LFLED® 4LV INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened
rmly. Apply weatherproof silicone sealant around the edge of the wall cover plate or junction box. This is especially
important with an uneven surface. Suitable for wet locations. Suitable for mounting within 1.2m (4ft) of the ground.
WALL MOUNTING
Fig: 1
Mount to a weatherproof junction box and cover plate (not
provided) as shown in Fig. 1. To ensure weatherproof seal, apply
weatherproof silicone sealant around the edge of the wall
cover plate or surface box. This is especially important with an
uneven wall surface.
1. Seal arm thread using Teon® tape or silicone sealant.
2. Thread xture into Cover Plate (sold separately).
3. Connect wires as shown in the wiring diagram (Fig. 3).
4. Attach Cover Plate to Junction Box (sold separately).
5. Aim oodlight in the direction desired and tighten Locknut
and Arm Screw.
Cover Plate
(sold separately)
Junction Box
(sold separately)
Arm Screw
GROUND MOUNTING
Mount to a Mighty Post (RAB Cat# MP19) as shown in Fig. 2.
1. Thread xture into Mighty Post Cap.
2. Connect wires as shown in the wiring diagram (Fig. 3) and
place inside the Mighty Post.
3. Place Mighty Post Cap on the Mighty Post.
4. Aim oodlight in the direction desired and tighten Locknut
and Arm Screw.
Mighty Post Cap
Mighty Post
Arm Screw
Fig: 2

INSTRUCTIONS
LFLED® 4LV INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mark[email protected]
WIRING
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
CLEANING & MAINTENANCE
TROUBLESHOOTING
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do not open the xture to clean the LED. Do not touch the
LED.
1. Check that the line voltage at the xture is correct. Refer to
wiring directions.
2. Keep leaves and debris out of hood.
LFLED4LV - IN - 0223
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly - sal[email protected]
Free Lighting Layouts
Answered online or by request
© 2023 RAB LIGHTING Inc.
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.
73105-RAB
The driver permits operation at 12 VAC ONLY. Wire LFLED4LV
using approved wiring devices for SPT-1 cord.
Use approved wiring devices for SPT-1 cord.
Reector door lens kit can be ordered separately:
LNSLFLED8 15° spot reector, door, lens kit for LFLED4LV
LSLFLED8 20° spot reector, door, lens kit for LFLED4LV
ACCESSORIES
Fig: 3