RAB WPLED20 User manual

20W LED WALLPACK INSTALLATION INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THEAPPLICABLE
INSTALLATION CODE BYA PERSON FAMILIAR WITH THE CONSTRUCTIONAND OPERATION OF THE PRODUCT.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
Thank you for buying
RAB LED lighting.
Comments? Call us at
888-RAB-1000, or email:
[email protected]
JUNCTION BOX MOUNT FOR
CONDUIT
For use on applications where conduit wiring is needed.
1. Loosen and remove (4) Lens Screws. Remove Door.
2. Loosen and remove (2) Housing Screws. Remove
Housing from Back Box. Keep Housing Gasket intact
for re-assembly.
3. Secure Back Box to the mounting surface using
hardware appropriate for that mounting surface.
4. Wire the fixture using UL listed wire connectors
according to NEC and local codes. Apply sealant to all
unused conduit entry points.
5. Place Gasket between Back Box and Housing.
Re-mount Housing to Back Box. Check Housing
Gasket seal all around the Back Box.
6. Re-mount Door to Housing. Tighten (4) Lens Screws.
Check door gasket (not shown) seal.
7. Fixture is UL Listed for down and up lighting and may
be mounted in either position. Fixture may not melt
heavy snow accumulation in an uplight position.
CAUTION: For proper weatherproof function all gaskets
must be seated properly and all screws inserted and
tightened firmly.
Lens
Screws
Junction Box Surface Mount
Back Box Housing
Gasket
Housing
Door
Housing
Screws
SURFACE MOUNT FOR
RECESSED JUNCTION BOX
For use with recessed junction box and wiring.
1. Mount Surface Plate to fixture with (4) Surface Plate
Screws. There are two screws from the front and two
screws from the back. Make sure Housing Gasket
makes complete seal all the way around.
2. Use supplied crossbar. Mount Crossbar to recessed
junction box with (2) screws.
3. Place Junction Box Gasket on back of the fixture.
Gasket should create seal against mounting surface.
4. Wire fixture to supply wires in recessed junction box
according to wiring section.
5. Use 1/4 x 20 stainless steel Mounting Screw to attach
fixture to Crossbar. Tighten Mounting Screw.
6. Cover screw with Cap, provided.
7. Fixture is UL Listed for down and up lighting and may
be mounted in either position. Fixture may not melt
heavy snow accumulation in an uplight position.
CAUTION: For proper weatherproof function all gaskets
must be seated properly and all screws inserted and
tightened firmly.
Crossbar
Junction
Box Gasket
Mounting
Screw Cap
Recessed
Junction Box
(not provided)
Surface
Plate
Housing
Gasket
(4) Surface
Plate Screws

20W LED WALLPACK INSTALLATION INSTRUCTIONS
TROUBLESHOOTING
1. Check that the line voltage at fixture is correct. Refer
to wiring directions.
2. Is the fixture is grounded properly?
3. Is the photocell, if used, functioning properly?
WPLED20x3-IN-1010
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool
enough to touch. Do not clean or maintain while
fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning
solution.
2. Do not open fixture to clean the LED. Do not touch
the LED.
-*()5
'*9563&
-*/& #-"$,
$0..0/ 8)*5&
(306/% (306/%
WIRING
Universal voltage driver permits operation at
100V to 277VAC, 50 or 60Hz except those factory
ordered with a 120V photocell (/PC).
1. Connect the black fixture lead to the (+) LINE
supply lead.
2. Connect the white fixture lead to the (-) COMMON
supply lead.
3. Connect the bare copper Ground wire from fixture to
supply ground.
JUNCTION BOX
1. The Junction box has (4) conduit entry points on the
center of each side and (1) in the center back.
2. Mounting Points are dimensioned below.
US and International Patents Pending
4 3/4”
2 3/16”
3 1/2”
1 1/8”
1 1/8”
Mounting Points
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.